Jump to content

CardBus/PCMCIA PC Cards for Leopard

~Eureka

By ~Eureka,
in Other Peripheral Devices

 Share
1,073 posts in this topic

Recommended Posts

gamerman315
gamerman315
Posted
Posted

So when booting my computer I get this error

 

IOPCCard info: Mac OS X PCMCIA Card Services 3.2.8

IOPCCard info: options: [pci] [cardbus] [pnp]

IOPCCard info: Intel ISA/PCI/CardBus PCIC probe:

IOPCCard notice: Bad bridge mapping at 0xd2100000!

IOPCCard info: no bridges found.

IOPCCardBridge::start failed

Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleIntelPIIXATARoot/PRID@0/AppleIntelICHxSATA/ATADeviceNub@0/AppleATADiskDriver/IOATABlockStorageDevice/IOBlockStorageDriver/FUJITSU MHV2200BT PL FUJITSU MHV2200BT PL/IOFDiskPartitionScheme/Untitled 1@1

 

and thus the PCMCIA slot wont turn on, yet when I turn my onboard lan off in the BIOS it loads perfectly fine and says this:

OPCCard info: Mac OS X PCMCIA Card Services 3.2.8

IOPCCard info: options: [pci] [cardbus] [pnp]

IOPCCard info: Intel ISA/PCI/CardBus PCIC probe:

IOPCCard info: TI XX12 rev 00 PCI-to-CardBus phys mem 0xd2108000 virt mem 0x47898000

IOPCCard info: host opts [0]: [serial pci & irq] [pci irq 17] [lat 168/176] [bus 3/3]

IOPCCard info: PCI card interrupts, PCI status changes

Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleIntelPIIXATARoot/PRID@0/AppleIntelICHxSATA/ATADeviceNub@0/AppleATADiskDriver/IOATABlockStorageDevice/IOBlockStorageDriver/FUJITSU MHV2200BT PL FUJITSU MHV2200BT PL/IOFDiskPartitionScheme/Untitled 1@1

IOPCCard info: cs: cb_alloc(bus 3): vendor 0x168c, device 0x0013

IOPCCard info: cs: cb_alloc(bus 3): found 1 functions

IOPCCard info: cs: cb_config(bus 3)

IOPCCard info: fn 0 bar 1: mem 0xd2020000-0xd202ffff

IOPCCard info: irq 17

 

Any idea what I need to do/modify to get this working?

Link to comment
Share on other sites
bredroll
bredroll
Posted
Posted
Hi, I have put the IOPCMCIAFamily.kext in the Extension folder with the right permissions but now leo (10.5.6) on my R52 won't boot.. it hang with no errors.

 

Here is a photo of the boot (10 minutes + with no reactions).

 

Any id�a ?

 

Sry for my poor english i'm french.

 

Thank you a lot :)

 

Hello, I had the same ( where boot gets stuck just after detecting the pcmcia bridge ), I found that this was because I had the IOPCCard kext in the Extensions folder instead of inside the IOPCMCIAFamily/Content/PlugIns folder.

 

It meant that the kernel would expect the newly found PCMCIA bridge to siddenly attach the root disk ( some netbooks have pcmcia attached disks ) so would wait forever for the boot drive. Don't directly put IOPCCard into Extensions

Link to comment
Share on other sites
gobe
gobe
Posted
Posted

Hi everybody,

 

first I want to thank for this great Project and I'm sorry for my bad english (hungarian living in germany).

 

I've a problem with my FireWire-PCMCIA-Card on an Acer Aspire 5610z. Saw a lot of posts for Acer Notebooks but unfortunately nothing helped me.

 

Cardbus-Controller is an: ene cb-712/ 714/810

FireWire-Card (2 ports): exsys ex-6600e (TI Chips)

 

So here's what I did.

Installed a 10.5.6 System by XxX.

Installed the IOPCMCIAFamily.kext for 10.5.6 (with the right rights), but the System hangs without error-msgs.

Than I tried rev8 and the Sytem was booting and recognizes the controller. Even the FireWire-Card is found.

But the Problem is that no devices are recognized when I connect them to the FireWire-Card.

First the System-Profiler said there are no FireWire-Drivers loaded, so I loaded them manually and the System-Profiler-Message changed to "Unable to list FireWire devices". Unfortunately this message tells the truth.

 

Here are my dmesg-outputs.

 

After loading IOPCCardFamily.kext and all FireWire-Kexts manually:

bash-3.2# dmesg | grep PC
Extension "com.apple.driver.ApplePCIConfigurator" has immediate dependencies on both com.apple.kernel and
com.apple.kpi components; use only one style.
PCI configuration changed (bridge=0 device=5 yenta=1)
Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleIntelPIIXATARoot/PRID@0/AppleIntelIC
HxSATA/ATADeviceNub@0/AppleATADiskDriver/IOATABlockStorageDevice/IOBlockStorageDriver/WDC WD1600BEVS-
22RST0 WDC WD1600BEVS-22RST0/IOFDiskPartitionScheme/Untitled 3@3
IOPCCard info:   Intel PCIC probe:   ENE 712/4 rev 10

 

After inserting the FireWire-Card:

bash-3.2# dmesg | grep PC
Extension "com.apple.driver.ApplePCIConfigurator" has immediate dependencies on both com.apple.kernel and
com.apple.kpi components; use only one style.
PCI configuration changed (bridge=0 device=5 yenta=1)
Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleIntelPIIXATARoot/PRID@0/AppleIntelIC
HxSATA/ATADeviceNub@0/AppleATADiskDriver/IOATABlockStorageDevice/IOBlockStorageDriver/WDC WD1600BEVS-
22RST0 WDC WD1600BEVS-22RST0/IOFDiskPartitionScheme/Untitled 3@3
IOPCCard info:   Intel PCIC probe:   ENE 712/4 rev 10
IOPCCard info:   cs: cb_alloc(bus 7): vendor 0x104c, device 0x8023
IOPCCard info:   cs: cb_alloc(bus 7): found 1 functions
IOPCCard info:   cs: cb_config(bus 7)
IOPCCard info:     fn 0 bar 1: mem 0xa000d000-0xa000d7ff
IOPCCard info:     fn 0 bar 3: mem 0xa000c000-0xa000c7ff
IOPCCard info:     fn 0 bar 2: mem 0xa0008000-0xa000bfff
IOPCCard info:     irq 16

bash-3.2# dmesg | grep FireWire
FireWire (OHCI) TI ID 8023 CardBus now active, GUID 2e0300422e040043; max speed s100.
bash-3.2#

 

Additionally I tried to load all Kexts while boot-time, with and without inserted FW-Card.

Still the same problem.

 

Any Ideas? Thanks a lot.

 

Cheers

gobe

Link to comment
Share on other sites
bredroll
bredroll
Posted
Posted
Definitely not working here.

http://twitpic.com/hve4d

 

It's a bummer too, because I just put 10.5.6 on my HP machine. Would like to get some kind of networking working (in my case, either the Pro/100 ethernet or a wireless PCMCIA card).

 

Very odd, Have you tried it in firefox?

 

If you have no luck, the previous version worked well for me ( the version on mediafire never worked properly for me )

 

See here: http://www.darkspace.org.uk/drupal/?q=node/92

 

Regards

 

Ian

Link to comment
Share on other sites
MrAnalyst
MrAnalyst
Posted
Posted
Thank you very much ! success

 

How can i make this driver work on snow leopard? i have Linksys WPC54G PCMCIA card and work fine on all leopard versions but not on snow leopard.if i install IOPCMCIAFamily.kext , snow leopard crashed.after i remove it get back to normal ;)

Link to comment
Share on other sites
  • 2 weeks later...
itjstagame
itjstagame
Posted
Posted
i used o2micro firewire ochi and reader sd not work with chunman kext in ideneb 1.6

 

 

Ok, I tried the latest in the 10.5.6 folder on my 10.6.1 install and I can boot fine and it loads the module fine. When I plug a card in I see this in syslog:

Oct 13 09:16:24 t60osx pcscd[404]: Non-smartcard device launched pcscd [Vendor: 0X483, Product: 0X2016]

Oct 13 09:16:24 t60osx pcscd[404]: Non-smartcard device launched pcscd [Vendor: 0XA, Product: 0]

 

Now this in particular is a 5-1 card reader with a card in it. There are no new disks in /dev and it says non-smartcard reader.

 

Actually testing further, plugging in the 5-1 reader empty generates no messages in syslog or anywhere, I can enter the PCMCIA card empty, and then only when I put an SD card in it do the above messages show up.

 

Is there some next step I'm missing to have it emulate a drive?

Link to comment
Share on other sites
  • 3 weeks later...
macfen
macfen
Posted
Posted

my carbus still not working with chun chan kext rev8, rev3 and the final. I have XXX ver.2 installed on my Acer Aspire 5633WLMI

 

O.K now carbus has get working with rev8 and after repair permissions with disk utility.

Tnx very much!

post-444721-1257091450_thumb.jpg

Link to comment
Share on other sites
  • 2 weeks later...
lazzy
lazzy
Posted
Posted

hi,

i look for driver for Ricoh

that my lspci

07:00.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 22)

07:00.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller [1180:0843] (rev 12)

07:00.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 12)

07:00.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev 12)

can i install for this?

Link to comment
Share on other sites
  • 3 weeks later...
  • 2 weeks later...
oldnapalm
oldnapalm
Posted
Posted

Hi ~Eureka,

 

I use your patched IOPCIFamily for 10.5.6 to get wireless card working on Snow Leopard, but only in 32 bit.

 

I tried to apply your patches from rev8 to IOPCIFamily-113, but it doesn't work like 10.5.6 version.

 

Would you share the source to your 10.5.6 version?

 

Thank you.

Link to comment
Share on other sites
  • 4 weeks later...
nexus77777
nexus77777
Posted
Posted

Hi Chun-Nan , thanks for this driver ++++ it works on my Toshiba Laptop,

 

BUT,

 

I noticed it prevend loading speedstep and ACPIthrottle on 10.4.10,

of course I try version for Tiger on your mediafire site...

So system become pourly slow...

 

Is there a way to fix it ???

Thanks...

Link to comment
Share on other sites
  • 3 weeks later...
Pedro Simão
Pedro Simão
Posted
Posted

Hello Guys,

 

I have installed an iPC 10.5.6. Everything ok, but after recognizing the ENE CB1410 the machine freezes.

 

I have tried to used every IOPCCardFamily and IOPCIFamily and IO PCMCIAFamily available in the forums, but I got the same result with everyone of them.

 

Now I am tryng to edit the Info.plist with my windows plist editor.

In windows I have the following IO values FF00 - FFFF, FD00 - FDFF,

And memory intervals F0404000 - f0404fff, f2bff000 - f2bfffff, c0000000 - c3ffffff

 

The problem is this IO values in the Info.plist are in a format like AAAAAAAAD/8=, so they are completly different from the values I see in Windows.

 

So my question is, how should my values look like in the Info.plist after I edit it?

I know it may seem a little newbie question, but I cant understand this.

 

Thx very much!

 

ps.: My machine is an Acer TravelMate 6292... If anyone could install a Hackintosh in it, just let me know how!

Link to comment
Share on other sites
mr ben
mr ben
Posted
Posted

hello ppl,

 

i have installed iDeneb 1.6 (10.5.8) lite edition and the only problem that i have is that i cannot use my PCMCIA modem (EV-DO) card to connect to the internet by dialing a connection with this PCMCIA card type II.

 

post-559330-1265463335_thumb.jpg

post-559330-1265463417_thumb.jpg

 

as you can see the card i think is installed because i can turn it off by pressing turn off from taskbar from up. The thing is that i cannot find this card in Network to can setup the PPP conection.

Is there anyone that can help me to use this card?

 

I have an HP530 Notebook PC

Core Duo 2.17 Ghz, 1,5 GB Ram, Intel GMA950 video card, 3945ABG wireless

 

Thank you

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...