Asus P5W DH Deluxe thread for 10.5.x Leo - 10.9.x Mavericks

[aliab]

has anyone managed to get the onboard sound working using EFIStudio?

 

Not yet the time to but you probably can try to find device path with :

 

./gfxutil -f pci8086,27d8

 

here :

 

PciRoot(0x0)/Pci(0x1b,0x0)

 

find the values with IORegistryexplorer

 

then edit this if it is different

 

<?xml version="1.0" encoding="UTF-8"?>

<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">

<plist version="1.0">

<dict>

<key>PciRoot(0x1)/Pci(0x1b,0x0)</key>

<dict>

<key>PinConfigurations</key>

<string></string>

<key>built-in</key>

<string>0x00</string>

<key>layout-id</key>

<string>0x0000000c</string>

<key>revision-id</key>

<string>0x00000001</string>

<key>subsystem-id</key>

<string>0x000081d8</string>

<key>subsystem-vendor-id</key>

<string>0x00001043</string>

<key>vendor-id</key>

<string>0x00008086</string>

</dict>

</dict>

</plist>

 

save change to hex

 

let us known about

 

EDIT/ working

[peach-os]

they are sata 3 Gb/s configured ?

You 're probably right, i'll have to try with another pair of disk or some kext i missed in the instalation

 

did you tried to configure a soft raid with disk utility and after hook it to orange sata ports ?

 

in the manual:for best results use serial ata 3.0 Gb/s hard disk drives listed in the EZ-backup compatibility list.visit the asus website for details

 

because the steelvine controller is connected to the fourth ich7 port, the whole bandwith is only 3gb/s - so two s-ata I drives should bring also good results - but for some reason they don´t. tested it and better results with s-ata II.

 

softraid and then connect to EZ backup?? two different things .....didn´t try it, but I´m pretty sure that EZ backup won´t recognize the disks as a raid config...weired idea

[kdp]

anyone know how to bypass the prompt all together so i don't have to press enter using chameleon boot dfe for HDD? my bluetooth keyboard doesn't recognize until osx starts to load, and i don't want to have to have a 2nd keyboard hooked up just to press enter during boot.

[Fresh1]

22/07/2008

time to update this tread with all you need and make clear some things

 

ISO FOR USE TO INSTALL THE RETAIL LEOPARD DVD 10.5 + UPDATE YOUR LEO to 10.5.4 from internet using the apple software update tool without any problem:

http://www.mediafire.com/?gmwgcwrvjgg

 

PAY ATTENTION MAYBE YOU MUST PUT IN YOUR BIOS UNDER CPU CONFIGURATION THE MAX CPU VALUE LIMIT to [DISABLED] and then ENABLE it after the successfull Leopard install (under verify)

ISOS TO USE AS BOOTLOADER 132 AFTER THE 10.5.4 UPDATE:

 

07/12/2008:

Added HDAenabler (thnx to Kabyl), IOAHCIfamily, IOnetworkingfamily, Chun-nan PS2/USB kexts for mause and keyboard, JMicronATA and more...

http://rapidshare.com/files/129023748/BURNME.iso.html

 

22/07/2008

Another version with the SMBIOSResolver.kext (SDRAM memory bug but wrks fine in all) THNX to SUPERHAI (www.superhai.com), it works with original applesmbios FROM 10.5.2 and up

http://www.mediafire.com/?6j9wcsxszlz

With those isos you can install the retail leopard, run it and keep your extensions folder like the original macs computers, thnx to GALAXY for his work "the ramdisk is dammn fast", thnx to the others for this fantastic bootloader ( def, kabyl, zef, bumby and all the chameleon gang!)

 

After the first update for e.g. from 10.5 to 10.5.4 (YES NOW U CAN!!) simply reboot and use the other iso.

 

After the 10.5.x update you will lost the QE on video card... reinstall it, be carefull to delete the old drivers before reintall, reinstall repair permission.

 

AUdio package installer for asus p5w dh deluxe : http://rapidshare.com/files/128111193/AUDIO.mpkg.zip.html

BIOS SETUP ver.2704

IN MAIN MENU:

-IDE in AHCI mode, ALPE and ASP Disabled

 

MENU ADVANCED, CPU CONFIGURATION

-MODIFY RATIO SUPPORT [DISABLED]

-MICROCODE UPDATION [ENABLED]

-MAX CPU VALUE LIMIT [ENABLED]

-EXECUTE DISABLED FUNCTION [ENABLED]

-ENHANCED C1 CONTROL [AUTO]

-VIRTUALIZATION TECHNOLY [ENABLED]

-INTEL SPEEDSTEP TECHNOLOGY [DISABLED]

 

MENU ADVANCED, CHIPSET MENU

-MEMORY REMAP FUTURE [ENABLED]

 

MENU POWER-SUSPEND MODE [s3 ONLY]

-RESPOST VIDEO ON S3 RESUME [YES]

-ACPI 2.0 SUPPORT [YES]

-ACPI APIC SUPPORT [YES]

 

MENU POWER, APM CONFIGURATION

Set the ps2 keyboard to awake from sleep with your pref button like space bar, CTRL esc etc... make your choice i used SPACE BAR

-Power on by ps2 mouse [ENABLED]

 

22/07/2008 BOOT FROM HARD DISK!!

 

ONLY AFTER THE RETAIL INSTALL USING THE FIRST CD BOOTLOADER....

 

FROM KALYWAY:

 

Download link : Chameleon_DFE_for_Hard_Disk.zip --->http://tinyurl.com/6je4eh

1 - Copy the contents of your "Extra" folder to "Extra Contents" directory link !!!

 

2- then run Chameleon_DFE_for_Hard_Disk.pkg and install it to your hard disk !!!

your are done ! now no need to use dfe 132 cd to boot your hd !!

enjoy!!

by kalyway !

COPY FROM THE CDBOOT ONLY THE MKEXT FILE ON THE INITRD:IMG (mount it)

 

IT WORKS FINE

 

About the kexts, SMBIOSresolver has a bug, for a moment not show the right memory setup, Superhai will make the nfo.plist editable for put it the correct value.

 

Can anyone tell me if there is a fix for the sdram memory bug? My ddr2 is still showing with a clock speed of 0 and as sdram? Thanks

[peach-os]

Can anyone tell me if there is a fix for the sdram memory bug? My ddr2 is still showing with a clock speed of 0 and as sdram? Thanks

 

because ddr is an sdram as well?

 

try another smbios to show you the memory speed or search for an smbios enabler.

[aliab]

has anyone managed to get the onboard sound working using EFIStudio?

 

here working plist (Time Machine and Audio)

 

<?xml version="1.0" encoding="UTF-8"?>

<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">

<plist version="1.0">

<dict>

<key>PciRoot(0x0)/Pci(0x1b,0x0)</key>

<dict>

<key>PinConfigurations</key>

<string></string>

<key>built-in</key>

<string>0x00</string>

<key>layout-id</key>

<string>0x0000000c</string>

<key>revision-id</key>

<string>0x00000001</string>

<key>subsystem-id</key>

<string>0x000081d8</string>

<key>subsystem-vendor-id</key>

<string>0x00001043</string>

<key>vendor-id</key>

<string>0x00008086</string>

</dict>

<key>PciRoot(0x0)/Pci(0x1c,0x3)/Pci(0x0,0x0)</key>

<dict>

<key>built-in</key>

<string>0x01</string>

</dict>

</dict>

</plist>

 

and the hex convertion string is:

 

6e01000001000000020000003f0000000100000002010c00d041030a0000000001010600031c0101

60000007fff0400160000006200750069006c0074002d0069006e000000050000000123010000070

000002010c00d041030a0000000001010600001b7fff04001c000000720065007600690073006900

f006e002d00690064000000080000000100000028000000500069006e0043006f006e00660069006

00750072006100740069006f006e00730000000400000018000000760065006e0064006f0072002d

069006400000008000000868000002c000000730075006200730079007300740065006d002d00760

65006e0064006f0072002d0069006400000008000000431000001e00000073007500620073007900

300740065006d002d0069006400000008000000d8810000180000006c00610079006f00750074002

00690064000000080000000c000000160000006200750069006c0074002d0069006e000000050000

000

[radlord]

is there any known fixes for the sound input not being recognised?

[Fresh1]

because ddr is an sdram as well?

 

try another smbios to show you the memory speed or search for an smbios enabler.

 

I understand that it is sdram just wondering why it does not show up as ddr. Does this make a difference performance wise. Currently i am using the boot disk that was packed in I think post 409 of this topic.

[peach-os]

I understand that it is sdram just wondering why it does not show up as ddr. Does this make a difference performance wise. Currently i am using the boot disk that was packed in I think post 409 of this topic.

 

no, it doesn´t make a difference.

[El Massman]

thanks alot aliab, i'll give it a go.

 

Marc

[Fresh1]

no, it doesn´t make a difference.

 

Thanks

[Han S]

Strange network problem ASUS P5W DH Deluxe + Kalyway 10.5.1

 

Hi guys,

A few months ago I had succesfully install Kalyway 10.5.1 on my P5W DH Deluxe. Everything worked just like this link told "http://xiwen.de/blog/index.php/2008/01/07/der-perfekte-mac/" unfortunately this link is dead.

Another similar link is this "http://macapper.com/2008/01/19/diy-hackint...c-pro-for-cheap"

The bios settings of these links are the same. I followed these settings to install Kalyway 10.5.1. There is one thing I didn't folow. I chose MBR insteed of GUID; I did chose GUID first but ended up that installed Kalyway 10.5.1 only booted up with the install DVD inside the player. So I chose MBR and the installed Kalyway 10.5.1 booted without the install DVD.

 

My spec are:

ASUS P5W DH Deluxe with bios version 2206

Intel Core 2 Duo E4500

Corsair memory 3 X 1GB

ASUS GT7300 Silent 256MB videocard

Nec DVD recorder PATA

Samsung 160GB SATA(I) HD

HD had 3 partition: Leopard, XP and Data. I had a dualboot system.

 

 

Recently I bough an Samsung 320GB SATA(II) HD and wanted to transfer Kalyway 10.5.1 from Samsung 160GB to Samsung 320GB by using the following methodes:

1. Back up with Carbon Copy Cloner 3.11 dierctly to Samsung 320GB (Leopard partition). Result: a blinking cursor.

2. Back up with Super Duper 2.5 dierctly to Samsung 320GB (Leopard partition). Result: a blinking cursor.

3. Back up with Super Duper 2.5 as a DMG file to Samsung 320GB (Data partition, this partition is Extended Journaled). Restore with Mac own Disk Utility. Result: a blinking cursor.

4. Back up with Mac own Disk Utility as a DMG file to Samsung 320GB (Data partition, this partition is Extended Journaled). Restore with Mac own Disk Utility. Result: a blinking cursor.

 

So I installed a fresh Kalyway 10.5.1 on my new Samsung 320GB SATA(II) HD using the same settings as I did with Samsung 160GB SATA(I) HD. After install and a restart, everything seemed OK. But there is no internet connection, because there is no ethernetacrd (that's what the hardware profile showed). Only the firewirecard is shown. It seemed there was no ethernet connection at all, the led at the UTP connector of the motherboard didn't light up or blink. Even the led of my router where the UTP cabel is connected didn't light up or blink.

There was also something weird with the connction. When I swich on the computer the led of my router where the UTP cabel is connected and the led at the UTP connector of the motherboard did light up!!! But when the Apple screen showed up (dark grey Apple logo on light grey background) I saw those leds turned off!!! It seemed there is wen somthing wrong during the boot procedure. But I still don't know what.

If I booted up XP (I have a dualboot system), there is network connection!

 

If I hook up the Samsung 160GB SATA(I) HD back, then there is connection again while in Leopard. I am sure there is no hardware issue.

 

Do anyone know the problem/solution?

 

Han S

[peach-os]

the things you are talking about are all common problems. you will find all the solutions including the boot problem without dvd. use this http://www.google.com/coop/cse?cx=00948655...297:e41g72sr-ba

 

I´m pretty sure that the reason for your network problem is that you didn´t choose the right options on the second install. the p5w mainboard is probably the easiest mainboard to install 100 % working os x on it

[Han S]

Hi peach-os,

 

Thanks for reply. But I think read to fast; you missed something.

I have installed succesfully Kalyway 10.5.1 on a Samsung 160GB SATA1 HD. I had followed the instruction from the link (see above).

When I tried the same with Samsung 320GB SATA2 HD. After succesfully installed and reboot; there is just no network connection.

The only option of the network during install is Realtek WIFI. I never chose that both by install.

 

Han S

[Fresh1]

Can anyone tell me exactly what kexts are needed for our system. currently I am using the bootdisk from post 409 in this topic since its wrapped up as an mkext i can not tell what kexts exactly are needed to boot this system.

[peach-os]

Hi peach-os,

 

Thanks for reply. But I think read to fast; you missed something.

I have installed succesfully Kalyway 10.5.1 on a Samsung 160GB SATA1 HD. I had followed the instruction from the link (see above).

When I tried the same with Samsung 320GB SATA2 HD. After succesfully installed and reboot; there is just no network connection.

The only option of the network during install is Realtek WIFI. I never chose that both by install.

 

Han S

 

no - I did read.but personally I wouldn´t consider having os x installed on an mbr partition instead of guid because of the dvd boot problem is a success. you will miss a few advantages. there are much better instructions in this forum than on that site you used. in this thread you will find almost every solution

http://forum.insanelymac.com/index.php?showtopic=68453

 

installing kaly 10.5.1 there are network settings for the pw5dh (not wireless). an other possibilty is that you install the IONetworkingFamily.kext from your working install.

[morfy]

here working plist (Time Machine and Audio)

 

<?xml version="1.0" encoding="UTF-8"?>

<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">

<plist version="1.0">

<dict>

<key>PciRoot(0x0)/Pci(0x1b,0x0)</key>

<dict>

<key>PinConfigurations</key>

<string></string>

<key>built-in</key>

<string>0x00</string>

<key>layout-id</key>

<string>0x0000000c</string>

<key>revision-id</key>

<string>0x00000001</string>

<key>subsystem-id</key>

<string>0x000081d8</string>

<key>subsystem-vendor-id</key>

<string>0x00001043</string>

<key>vendor-id</key>

<string>0x00008086</string>

</dict>

<key>PciRoot(0x0)/Pci(0x1c,0x3)/Pci(0x0,0x0)</key>

<dict>

<key>built-in</key>

<string>0x01</string>

</dict>

</dict>

</plist>

 

and the hex convertion string is:

 

6e01000001000000020000003f0000000100000002010c00d041030a0000000001010600031c0101

60000007fff0400160000006200750069006c0074002d0069006e000000050000000123010000070

000002010c00d041030a0000000001010600001b7fff04001c000000720065007600690073006900

f006e002d00690064000000080000000100000028000000500069006e0043006f006e00660069006

00750072006100740069006f006e00730000000400000018000000760065006e0064006f0072002d

069006400000008000000868000002c000000730075006200730079007300740065006d002d00760

65006e0064006f0072002d0069006400000008000000431000001e00000073007500620073007900

300740065006d002d0069006400000008000000d8810000180000006c00610079006f00750074002

00690064000000080000000c000000160000006200750069006c0074002d0069006e000000050000

000

 

 

me some information on to extract? What we need to delete files? And what change? thanks in advance!

[aliab]

me some information on to extract? What we need to delete files? And what change? thanks in advance!

 

you can make a new com.apple.Boot.plist with this string (ethernet and Audio ALC882) in textedit

replace your existing and then launch EFIStudio to add 8800 GT string

 

<?xml version="1.0" encoding="UTF-8"?>

<!DOCTYPE plist PUBLIC "-//Apple Computer//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">

<plist version="1.0">

<dict>

<key>Kernel</key>

<string>mach_kernel</string>

<key>Kernel Flags</key>

<string></string>

<key>device-properties</key>

<string>6e01000001000000020000003f0000000100000002010c00d041030a0000000001010600031c0

01060000007fff0400160000006200750069006c0074002d0069006e000000050000000123010000

700000002010c00d041030a0000000001010600001b7fff04001c000000720065007600690073006

006f006e002d00690064000000080000000100000028000000500069006e0043006f006e00660069

06700750072006100740069006f006e00730000000400000018000000760065006e0064006f00720

2d0069006400000008000000868000002c000000730075006200730079007300740065006d002d00

60065006e0064006f0072002d0069006400000008000000431000001e00000073007500620073007

007300740065006d002d0069006400000008000000d8810000180000006c00610079006f00750074

02d00690064000000080000000c000000160000006200750069006c0074002d0069006e000000050

000000

</string>

<key>Graphics Mode</key>

    <string>1920x1200x32</string>

</dict>

</plist>

[morfy]

you can make a new com.apple.Boot.plist with this string (ethernet and Audio ALC882) in textedit

replace your existing and then launch EFIStudio to add 8800 GT string

 

<?xml version="1.0" encoding="UTF-8"?>

<!DOCTYPE plist PUBLIC "-//Apple Computer//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">

<plist version="1.0">

<dict>

<key>Kernel</key>

<string>mach_kernel</string>

<key>Kernel Flags</key>

<string></string>

<key>device-properties</key>

<string>6e01000001000000020000003f0000000100000002010c00d041030a0000000001010600031c0

01060000007fff0400160000006200750069006c0074002d0069006e000000050000000123010000

700000002010c00d041030a0000000001010600001b7fff04001c000000720065007600690073006

006f006e002d00690064000000080000000100000028000000500069006e0043006f006e00660069

06700750072006100740069006f006e00730000000400000018000000760065006e0064006f00720

2d0069006400000008000000868000002c000000730075006200730079007300740065006d002d00

60065006e0064006f0072002d0069006400000008000000431000001e00000073007500620073007

007300740065006d002d0069006400000008000000d8810000180000006c00610079006f00750074

02d00690064000000080000000c000000160000006200750069006c0074002d0069006e000000050

000000

</string>

<key>Graphics Mode</key>

    <string>1920x1200x32</string>

</dict>

</plist>

 

 

But the files ALCinject and applehda must leave? Why do I

tried to delete them and I do not see the sound card.

[aliab]

But the files ALCinject and applehda must leave? Why do I

tried to delete them and I do not see the sound card.

 

no you've to delete ALCinject only and keep ypur patched AppleHDA

and repair permissions

 

cd /

sudo -s

chmod 1775 /

chown root:wheel /

chmod 755 mach_kernel

chown root:wheel mach_kernel

chmod 644 Library/Preferences/SystemConfiguration/com.apple.Boot.plist

chown root:admin Library/Preferences/SystemConfiguration/com.apple.Boot.plist

chmod -R 755 System/Library/Extensions

chown -R root:wheel System/Library/Extensions

rm -R System/Library/Extensions.mkext

diskutil repairPermissions /

 

reboot with F8 -v -f

[morfy]

no you've to delete ALCinject only and keep ypur patched AppleHDA

and repair permissions

 

cd /

sudo -s

chmod 1775 /

chown root:wheel /

chmod 755 mach_kernel

chown root:wheel mach_kernel

chmod 644 Library/Preferences/SystemConfiguration/com.apple.Boot.plist

chown root:admin Library/Preferences/SystemConfiguration/com.apple.Boot.plist

chmod -R 755 System/Library/Extensions

chown -R root:wheel System/Library/Extensions

rm -R System/Library/Extensions.mkext

diskutil repairPermissions /

 

reboot with F8 -v -f

 

Unfortunately does not work in any way. I resolved with the new AppleHDA. through the same

[avatar382]

I'm having a strange issue with sleep.

 

The machine will sleep and wake correctly exactly once. After that once, if I try to have the machine sleep again, it will not enter a full sleep mode. The ethernet device will turn off and it sounds like the hard drives is spinning down, but the fans keep running at normal speed, and the system will not wake.

 

The first time, if I try to wake from sleep with the keyboard, the screen will not power on. It works (just once) when I wake the computer by using the power button. I don't really mind the annoyance of having to hit the power button, but a sleep function that works only once isn't much better than having a sleep function at all.

 

I've tried this several times, with a variety of BIOS settings. (It will only sleep once set to S3. Resume video BIOS on wake doesn't seem to matter) I don't see any consistent notices in the system.log file.

 

Specs:

 

ASUS P5WDH

4 GB ECC RAM

ASUS GeForce 8800GT 512MB (Nvinject)

3 Samsung LCDs connected to a Matrox TripleHead2Go (the OS is only aware of a single "monitor")

Pentium Dual-Core E2140 @ 2.66GHz (bus overclocked to 1333, nothing else overclocked)

IBM Model M keyboard connected to Radio Shack PS2 to USB adapter

Microsoft Wheel Mouse Optical USB

Macnally FireWire enclosure with 500GB drive for Time Machine

2 Seagate SATA 160GB drives, 1 with OSX, 1 with Vista

1 WD 1TB GreenPower SATA drive

 

Any ideas? Thanks!

 

Edit:

 

Forgot to mention:

Using Kalyway. Installed of the 10.5.1 CD, system has been upgraded to 10.5.4.

I am running the AHCI fix to get rid of the orange icons, and NVinject.

[aliab]

I'm having a strange issue with sleep.

 

The machine will sleep and wake correctly exactly once. After that once, if I try to have the machine sleep again, it will not enter a full sleep mode. The ethernet device will turn off and it sounds like the hard drives is spinning down, but the fans keep running at normal speed, and the system will not wake.

 

The first time, if I try to wake from sleep with the keyboard, the screen will not power on. It works (just once) when I wake the computer by using the power button. I don't really mind the annoyance of having to hit the power button, but a sleep function that works only once isn't much better than having a sleep function at all.

 

I've tried this several times, with a variety of BIOS settings. (It will only sleep once set to S3. Resume video BIOS on wake doesn't seem to matter) I don't see any consistent notices in the system.log file.

 

Specs:

 

ASUS P5WDH

4 GB ECC RAM

ASUS GeForce 8800GT 512MB (Nvinject)

3 Samsung LCDs connected to a Matrox TripleHead2Go (the OS is only aware of a single "monitor")

Pentium Dual-Core E2140 @ 2.66GHz (bus overclocked to 1333, nothing else overclocked)

IBM Model M keyboard connected to Radio Shack PS2 to USB adapter

Microsoft Wheel Mouse Optical USB

Macnally FireWire enclosure with 500GB drive for Time Machine

2 Seagate SATA 160GB drives, 1 with OSX, 1 with Vista

1 WD 1TB GreenPower SATA drive

 

Any ideas? Thanks!

 

Edit:

 

Forgot to mention:

Using Kalyway. Installed of the 10.5.1 CD, system has been upgraded to 10.5.4.

I am running the AHCI fix to get rid of the orange icons, and NVinject.

 

You don,'t have to fix AHCI with this mobo keep the vanilla if you want to get rid of orange icons the only kext to mod is IOAHCIFamily.kext

 

here the definitive list of modification to get what is far the best mobo i've tried (with perfect sleep and wake)

 

Remove only :

 

AppleIntelCPUPowerManagement.kext

 

Mod :

 

IOAHCIFamily.kext (orange icons)

AppleHDA.kext

 

Add :

 

AppleSMBIOSEFI.kext link

dsmos.kext

 

com.apple.Boot.plist (with efi string)

 

 

About WIFI ; i can't get working with the realtek driver the USB WLAN application jump in the dock and that's all

If someone could help me

 

Thank's to all

[mr.mcgoo]

I tried the Boot 132 iso listed here and on that thread and neither let me get past the space desktop. The one listed here tells me to restart on the white apple screen and the first one on the original Boot 132 thread get to space screen but stays there with the ball icon spinning.

 

I'm using bios 2704 now. I'm using the bios settings listed here...

[thefinalprophecy]

I'm having a strange issue with sleep.

 

The machine will sleep and wake correctly exactly once. After that once, if I try to have the machine sleep again, it will not enter a full sleep mode. The ethernet device will turn off and it sounds like the hard drives is spinning down, but the fans keep running at normal speed, and the system will not wake.

 

The first time, if I try to wake from sleep with the keyboard, the screen will not power on. It works (just once) when I wake the computer by using the power button. I don't really mind the annoyance of having to hit the power button, but a sleep function that works only once isn't much better than having a sleep function at all.

 

I've tried this several times, with a variety of BIOS settings. (It will only sleep once set to S3. Resume video BIOS on wake doesn't seem to matter) I don't see any consistent notices in the system.log file.

This happens to me too. Sleep is inconsistent for me lately. Not sure why.