Carnag Posted September 23, 2007 Share Posted September 23, 2007 Carnag, ... Download the info.plist !-->Info.zip Hi master, I have tried it but probably I'm doing something wrong. I deleted natid.kext and atidrv.kext then added ATY_Alopias.kext and repair permissions. Please apologize my stupid questoin and could you tell me which driver should I use actually. THX Link to comment Share on other sites More sharing options...
Scrizz Posted September 23, 2007 Share Posted September 23, 2007 @Bluejacky: Try installing without the ATITVOUT. Link to comment Share on other sites More sharing options...
raulb Posted September 23, 2007 Share Posted September 23, 2007 This is an SOS to Bronya. I had a perfectly working system with Uphuck 1.4i R2. Then in upgrade quest I deleted that Uphuck installation and tried to install XXX_10.4.10. On XXX-10.4.10 I couldn't get QE & CI working with your new driver and couldn't even log in, was getting stuck on the blue screen after boot and so reinstalled Uphuck after re-formatting my Mac partition. Now with your installer QE, CI or rotation is not working at all. On this same system just 2 days ago I had your driver install and work perfectly. Even your original driver one previously posted on page 1 was woking with QE and CI. I am at an odds to debug this, I am just surprised what could go worng with a clean installation with nothing installed, I even selected the same options on the Uphuck installer that I did last time just to keep the system identical. I just cannot think of any variable that can affect this. The only thing is last time I installed your original driver, had it working and then ran your new installer. Also one more thing I have noticedin the boot screen is device ID is coming twice, first as 0x72A0 and then as 0X7280 ( I think previously both time ti was coming 0x7290) In system profiler its shown as 7280 though. Am running out of ideas to debug this. Any thing you can think of that could have made the second install fail? Anything I can do and check? Link to comment Share on other sites More sharing options...
Carnag Posted September 23, 2007 Share Posted September 23, 2007 This is an SOS to Bronya. I had a perfectly working system with Uphuck 1.4i R2. Then in upgrade quest I deleted that Uphuck installation and tried to install XXX_10.4.10. On XXX-10.4.10 I couldn't get QE & CI working with your new driver and couldn't even log in, was getting stuck on the blue screen after boot and so reinstalled Uphuck after re-formatting my Mac partition. Now with your installer QE, CI or rotation is not working at all. On this same system just 2 days ago I had your driver install and work perfectly. Even your original driver one previously posted on page 1 was woking with QE and CI. I am at an odds to debug this, I am just surprised what could go worng with a clean installation with nothing installed, I even selected the same options on the Uphuck installer that I did last time just to keep the system identical. I just cannot think of any variable that can affect this. The only thing is last time I installed your original driver, had it working and then ran your new installer. Also one more thing I have noticedin the boot screen is device ID is coming twice, first as 0x72A0 and then as 0X7280 ( I think previously both time ti was coming 0x7290) In system profiler its shown as 7280 though. Am running out of ideas to debug this. Any thing you can think of that could have made the second install fail? Anything I can do and check? Yeah I have the same problem. Link to comment Share on other sites More sharing options...
Bronya Posted September 23, 2007 Author Share Posted September 23, 2007 raulb "( I think previously both time ti was coming 0x7290)" <-- You should disconnected computer ! And true computer ... Could you tell me which pkg is for DVI out? ATINDRV.kext To all, i will put ATINDRV.kext for 10.4.10... Link to comment Share on other sites More sharing options...
Carnag Posted September 23, 2007 Share Posted September 23, 2007 Hi Bronya, I have tried it but probably I'm doing something wrong. I deleted natid.kext and atidrv.kext then added ATY_Alopias.kext and repair permissions. Please apologize my stupid questoin and could you tell me which driver should I use actually. THX Link to comment Share on other sites More sharing options...
Bronya Posted September 23, 2007 Author Share Posted September 23, 2007 Hi Bronya,I have tried it but probably I'm doing something wrong. I deleted natid.kext and atidrv.kext then added ATY_Alopias.kext and repair permissions. Please apologize my stupid questoin and could you tell me which driver should I use actually. THX Yep ... ATY_Alopias.kext in folder /system/library/extensions/ ... Reboot ... Try ... Link to comment Share on other sites More sharing options...
Carnag Posted September 23, 2007 Share Posted September 23, 2007 Yep ...ATY_Alopias.kext in folder /system/library/extensions/ ... Reboot ... Try ... precisely, I have added ATY_Alopias.kext (with new Info.plist). Probably I shouldn't delete original rls drivers... Link to comment Share on other sites More sharing options...
Bronya Posted September 23, 2007 Author Share Posted September 23, 2007 precisely, I have added ATY_Alopias.kext (with new Info.plist). Probably I shouldn't delete original rls drivers... Nope ! You download http://forum.insanelymac.com/index.php?act...st&id=14973 and install in folder /system/library/extensions/ ... Link to comment Share on other sites More sharing options...
Carnag Posted September 23, 2007 Share Posted September 23, 2007 Nope ! You download http://forum.insanelymac.com/index.php?act...st&id=14973 and install in folder /system/library/extensions/ ... Fine Thx - I finish my work. I'll try it... Link to comment Share on other sites More sharing options...
raulb Posted September 24, 2007 Share Posted September 24, 2007 Ooops, that 7290 should be 7280! Ok, there is something weird happening. I uninstalled the new driver, then rebooted and installed your original driver (posted just before you updated the page 1 on this thread). Then checked if I was getting CI and QE with that as I was the last time. I was. I rebooted again and then installed your new driver. This time it was working perfectly as before. I do the permissions, kext cache and disk utility thing every time I install or uninstall. Confused. Anyway I then installed PascalW 10.4.10 update and everything is working perfectly. Quite wierd but I am relieved I have got it working again. The verbose mode boot screen is still showing x72A0 and x07280 but thats not affecting the login or performance. Thanks Bronya. Link to comment Share on other sites More sharing options...
Scrizz Posted September 24, 2007 Share Posted September 24, 2007 x1950gt installer Link to comment Share on other sites More sharing options...
nikeita Posted September 24, 2007 Share Posted September 24, 2007 x1950gt installer hi scrizz thx for you new installer i see in your sign you upgraded to 10.4.10 with koolkal i tried to do same but my system reset just at boot ( at kernel load) dont'know if the problem is the kernel 8.10.3 ( tried also 8.10.1) or a video problem (the reset occur on changing video mode) any hint? thx Link to comment Share on other sites More sharing options...
Nadeem Posted September 25, 2007 Share Posted September 25, 2007 hi scrizzthx for you new installer i see in your sign you upgraded to 10.4.10 with koolkal i tried to do same but my system reset just at boot ( at kernel load) dont'know if the problem is the kernel 8.10.3 ( tried also 8.10.1) or a video problem (the reset occur on changing video mode) any hint? thx Don't use 8.10.3 , its hella buggy , couldnt start my system with it .. so re-formatted , and had to install everything from the scratch ... use 8.10.1 if u have sse3... Link to comment Share on other sites More sharing options...
cfmwan Posted September 25, 2007 Share Posted September 25, 2007 Thank you! Sapphire X1950GT QE/CI DVI out OK My id72881002 Link to comment Share on other sites More sharing options...
Carnag Posted September 25, 2007 Share Posted September 25, 2007 x1950gt installer plz for 1950pro (HW 7280) also (OS 10.4.10) THX Link to comment Share on other sites More sharing options...
Kevin Email Posted September 25, 2007 Share Posted September 25, 2007 First Off I need to say thanks!!! this rocks and works great on my 10.4.8 JaS-> 10.4.10 install. It even see's my secondary adapter just fine but through DVI the second monitor cannot be activated. Anyone get the second monitor running on a X9150PRO PCIe 512Mb? Thanks, Kevin Link to comment Share on other sites More sharing options...
Carnag Posted September 25, 2007 Share Posted September 25, 2007 Nope ! You download http://forum.insanelymac.com/index.php?act...st&id=14973 and install in folder /system/library/extensions/ ... Hi Bronya, so I have tried ATY_Alopias.kext but nothing happend just I have bad GPU parameters. I hope for a wonder which solve all this {censored} problems wirh ATI 1950 PRO. ATI Radeon X1950 Series: Chipset Model: ATI Radeon X1950 Series Type: Display Bus: PCIe VRAM (Total): 256 MB -> I have 512 MB Vendor: ATI (0x1002) Device ID: 0x7280 Revision ID: 0x009a Displays: Display: Resolution: 1024 x 768 Depth: 32-bit Color Core Image: Not Supported Main Display: Yes Mirror: Off Online: Yes Quartz Extreme: Not Supported Display: THX Carnag Link to comment Share on other sites More sharing options...
Bronya Posted September 25, 2007 Author Share Posted September 25, 2007 Hi Bronya, so I have tried ATY_Alopias.kext but nothing happend just I have bad GPU parameters. I hope for a wonder which solve all this {censored} problems wirh ATI 1950 No, you not correctly also did not load it correctly! In the beginning for you should work QE/CI, and then alopias! Then I will send soon a package... Kevin Email , you download driver from post 1 ? Link to comment Share on other sites More sharing options...
Carnag Posted September 25, 2007 Share Posted September 25, 2007 No, you not correctly also did not load it correctly! In the beginning for you should work QE/CI, and then alopias! Then I will send soon a package... Kevin Email , you download driver from post 1 ? Good notice QE/CI should work? I didn't found any driver which works in XxX_OS_x86_10.4.10_Install_Disc Link to comment Share on other sites More sharing options...
Bronya Posted September 25, 2007 Author Share Posted September 25, 2007 Good notice QE/CI should work? I didn't found any driver which works in XxX_OS_x86_10.4.10_Install_Disc Oh, tomorrow the driver for 10.4.10 ... I tired ... Link to comment Share on other sites More sharing options...
Carnag Posted September 25, 2007 Share Posted September 25, 2007 Oh, tomorrow the driver for 10.4.10 ...I tired ... Coooool, Thanks Link to comment Share on other sites More sharing options...
Scrizz Posted September 25, 2007 Share Posted September 25, 2007 w00t Matrox Parhelia FTW Link to comment Share on other sites More sharing options...
Bluejacky Posted September 26, 2007 Share Posted September 26, 2007 @Bluejacky:Try installing without the ATITVOUT. Hi, Scrizz Thank you. I have tried it, but get same result. Link to comment Share on other sites More sharing options...
Kevin Email Posted September 26, 2007 Share Posted September 26, 2007 Yes. I downloaded from the First Post downloaded the 9/17/07 revision. Will try fooling around with it alittle more. Also will try hooking the second monitor up through DVI->VGA Adapter and see if that helps. Kevin UPDATE: TRIED DVI-VGA Adapter also still cannot activate the second monitor. Link to comment Share on other sites More sharing options...
Recommended Posts