Satashi Zero Posted May 9, 2020 Share Posted May 9, 2020 Hello, My hackintosh (OpenCore) is Gigabyte z390 aorus ultra, i7 9700k, Gigabyte RX 5600 XT. everything worked fine except sometimes (randomly) it booted fail. I acttached one log for success boot, and one for failure boot. Hope someone can help me find what is the problem https://mega.nz/file/Kw0GGAQa#RiVm8z2T__Y8CnTZTYvyjdA4riGluv9ZmrpEZ-BWBv4 Thank a lot ! Link to comment Share on other sites More sharing options...
vamose Posted May 9, 2020 Share Posted May 9, 2020 Please help with OpenCore Bootloader. Made mutiple attempts but never made progress beyond the boot screen. Attached are the relevant files & system info. Generated DSDT using DPCIManager SSDT-EC & SSDT-PLUG using MaciASL Hardware CPU: Intel® Core™ i7-4790K Processor MOBO: Gigabyte B85M-D3H ver. F9 GPU: NVIDIA Quadro Fx 1800 OpenCore_Files.zip Link to comment Share on other sites More sharing options...
nmano Posted May 9, 2020 Share Posted May 9, 2020 0.5.9 I have halting on critical error. ...BootEntryManagement.c(184):FileSystem=void I don't know how to fix this Error. Link to comment Share on other sites More sharing options...
Matgen84 Posted May 9, 2020 Share Posted May 9, 2020 27 minutes ago, nmano said: 0.5.9 I have halting on critical error. ...BootEntryManagement.c(184):FileSystem=void I don't know how to fix this Error. If you want, try these files, I've compiled: BOOTx64.efi.zip OpenCore.efi.zip 1 Link to comment Share on other sites More sharing options...
olmirror Posted May 9, 2020 Share Posted May 9, 2020 (edited) After having played around with opencore for about a week I have it running on my hackintosh/10.14.6 (X99-UD4, 5820k, vega64). It took me quite some browsing in order to figure out how to enable XCPM and finally got it running, it's actually easier to set up than in clover and much better. Geekbench scores are low but with PMDrvr.kext scores are considerably higher and where they should be. (Same with clover and have no idea why.) But what I would like to ask why I get a 'Clover hw.busfrequency error detected : 17d78400' warning? Is this cosmetic as my system seems to be running stable? In clover there is a QPI setting that can be set to 100 which I can't find in Opencore. Is this related? Anyway I uploaded my Efi files and was hoping someone could either take a look or have some suggestions. Any pointers in the right direction are greatly appreciated. And I also wanted to use this opportunity to thank all the people who have made Opencore happen! Your hard work and patience in helping this community out is astounding... nmano, with your posts all over the internet I wouldn't be near to having my setup run as it does! Thanks bro... AppleIntelInfo.kext v3.0 Copyright © 2012-2017 Pike R. Alpha. All rights reserved. Settings: ------------------------------------------ enableHWP............................... : 0 logMSRs................................. : 1 logIGPU................................. : 0 logIntelRegs............................ : 0 logCStates.............................. : 1 logIPGStyle............................. : 1 Warning: Clover hw.busfrequency error detected : 17d78400 InitialTSC.............................. : 0xb8634dc17fbb (6143 MHz) MWAIT C-States.......................... : 8480 Processor Brandstring................... : Intel(R) Core(TM) i7-5820K CPU @ 3.30GHz Processor Signature..................... : 0x306F2 ------------------------------------------ - Family............................... : 6 - Stepping............................. : 2 - Model................................ : 0x3F (63) Model Specific Registers (MSRs) ------------------------------------------ MSR_IA32_PLATFORM_ID..............(0x17) : 0x8000000000000 ------------------------------------------ - Processor Flags...................... : 2 MSR_CORE_THREAD_COUNT.............(0x35) : 0x6000C ------------------------------------------ - Core Count........................... : 6 - Thread Count......................... : 12 MSR_PLATFORM_INFO.................(0xCE) : 0x20080C3BF3812100 ------------------------------------------ - Maximum Non-Turbo Ratio.............. : 0x21 (3300 MHz) - Ratio Limit for Turbo Mode........... : 1 (programmable) - TDP Limit for Turbo Mode............. : 1 (programmable) - Low Power Mode Support............... : 1 (LPM supported) - Number of ConfigTDP Levels........... : 1 (additional TDP level(s) available) - Maximum Efficiency Ratio............. : 12 - Minimum Operating Ratio.............. : 8 MSR_PMG_CST_CONFIG_CONTROL........(0xE2) : 0x1E000005 ------------------------------------------ - I/O MWAIT Redirection Enable......... : 0 (not enabled) - CFG Lock............................. : 0 (MSR not locked) - C3 State Auto Demotion............... : 1 (enabled) - C1 State Auto Demotion............... : 1 (enabled) - C3 State Undemotion.................. : 1 (enabled) - C1 State Undemotion.................. : 1 (enabled) - Package C-State Auto Demotion........ : 0 (disabled/unsupported) - Package C-State Undemotion........... : 0 (disabled/unsupported) MSR_PMG_IO_CAPTURE_BASE...........(0xE4) : 0x10414 ------------------------------------------ - LVL_2 Base Address................... : 0x414 - C-state Range........................ : 1 (C-States not included, I/O MWAIT redirection not enabled) IA32_MPERF........................(0xE7) : 0x21898E33CC IA32_APERF........................(0xE8) : 0x2C359BEE5F MSR_FLEX_RATIO...................(0x194) : 0xE0000 ------------------------------------------ MSR_IA32_PERF_STATUS.............(0x198) : 0x27FF00002B00 ------------------------------------------ - Current Performance State Value...... : 0x2B00 (4300 MHz) MSR_IA32_PERF_CONTROL............(0x199) : 0x2B00 ------------------------------------------ - Target performance State Value....... : 0x2B00 (4300 MHz) - Intel Dynamic Acceleration........... : 0 (IDA engaged) IA32_CLOCK_MODULATION............(0x19A) : 0x0 IA32_THERM_INTERRUPT.............(0x19B) : 0x0 IA32_THERM_STATUS................(0x19C) : 0x88370000 ------------------------------------------ - Thermal Status....................... : 0 - Thermal Log.......................... : 0 - PROCHOT # or FORCEPR# event.......... : 0 - PROCHOT # or FORCEPR# log............ : 0 - Critical Temperature Status.......... : 0 - Critical Temperature log............. : 0 - Thermal Threshold #1 Status.......... : 0 - Thermal Threshold #1 log............. : 0 - Thermal Threshold #2 Status.......... : 0 - Thermal Threshold #2 log............. : 0 - Power Limitation Status.............. : 0 - Power Limitation log................. : 0 - Current Limit Status................. : 0 - Current Limit log.................... : 0 - Cross Domain Limit Status............ : 0 - Cross Domain Limit log............... : 0 - Digital Readout...................... : 55 - Resolution in Degrees Celsius........ : 1 - Reading Valid........................ : 1 (valid) MSR_THERM2_CTL...................(0x19D) : 0x0 IA32_MISC_ENABLES................(0x1A0) : 0x850089 ------------------------------------------ - Fast-Strings......................... : 1 (enabled) - FOPCODE compatibility mode Enable.... : 0 - Automatic Thermal Control Circuit.... : 1 (enabled) - Split-lock Disable................... : 0 - Performance Monitoring............... : 1 (available) - Bus Lock On Cache Line Splits Disable : 0 - Hardware prefetch Disable............ : 0 - Processor Event Based Sampling....... : 0 (PEBS supported) - GV1/2 legacy Enable.................. : 0 - Enhanced Intel SpeedStep Technology.. : 1 (enabled) - MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported) - Adjacent sector prefetch Disable..... : 0 - CFG Lock............................. : 0 (MSR not locked) - xTPR Message Disable................. : 1 (disabled) MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x5E0A00 ------------------------------------------ - Turbo Attenuation Units.............. : 0 - Temperature Target................... : 94 - TCC Activation Offset................ : 0 MSR_MISC_PWR_MGMT................(0x1AA) : 0x400000 ------------------------------------------ - EIST Hardware Coordination........... : 0 (hardware coordination enabled) - Energy/Performance Bias support...... : 1 - Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software) - Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores) - SpeedShift Technology Enable......... : 0 (disabled) - SpeedShift Interrupt Coordination.... : 0 (disabled) - SpeedShift Energy Efficient Perf..... : 0 (disabled) - SpeedShift Technology Setup for HWP.. : No (not setup for HWP) MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x22222B2B2B2B2B2B ------------------------------------------ - Maximum Ratio Limit for C01.......... : 2B (4300 MHz) - Maximum Ratio Limit for C02.......... : 2B (4300 MHz) - Maximum Ratio Limit for C03.......... : 2B (4300 MHz) - Maximum Ratio Limit for C04.......... : 2B (4300 MHz) - Maximum Ratio Limit for C05.......... : 2B (4300 MHz) - Maximum Ratio Limit for C06.......... : 2B (4300 MHz) IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x0 MSR_POWER_CTL....................(0x1FC) : 0x2104005B ------------------------------------------ - Bi-Directional Processor Hot......... : 1 (enabled) - C1E Enable........................... : 1 (enabled) MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03 ------------------------------------------ - Power Units.......................... : 3 (1/8 Watt) - Energy Status Units.................. : 14 (61 micro-Joules) - Time Units .......................... : 10 (976.6 micro-Seconds) MSR_PKG_POWER_LIMIT..............(0x610) : 0x7FFD00014EA82 ------------------------------------------ - Package Power Limit #1............... : 3408 Watt - Enable Power Limit #1................ : 1 (enabled) - Package Clamping Limitation #1....... : 0 (disabled) - Time Window for Power Limit #1....... : 10 (2560 milli-Seconds) - Package Power Limit #2............... : 4090 Watt - Enable Power Limit #2................ : 1 (enabled) - Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2) - Time Window for Power Limit #2....... : 3 (20 milli-Seconds) - Lock................................. : 0 (MSR not locked) MSR_PKG_ENERGY_STATUS............(0x611) : 0x3B2E59B ------------------------------------------ - Total Energy Consumed................ : 3787 Joules (Watt = Joules / seconds) MSR_CONFIG_TDP_NOMINAL...........(0x648) : 0x21 MSR_CONFIG_TDP_LEVEL1............(0x649) : 0x940000001E0460 MSR_CONFIG_TDP_LEVEL2............(0x64a) : 0x94000000000000 MSR_CONFIG_TDP_CONTROL...........(0x64b) : 0x0 MSR_TURBO_ACTIVATION_RATIO.......(0x64c) : 0x0 MSR_PKGC3_IRTL...................(0x60a) : 0x0 MSR_PKGC6_IRTL...................(0x60b) : 0x0 MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x1A99BDCBB MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0 MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x1A99BDCBB MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0 MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x6580D9784 IA32_TSC_DEADLINE................(0x6E0) : 0xB8635998ABC0 CPU Ratio Info: ------------------------------------------ Base Clock Frequency (BLCK)............. : 100 MHz Maximum Efficiency Ratio/Frequency...... : 12 (1200 MHz) Maximum non-Turbo Ratio/Frequency....... : 33 (3300 MHz) Maximum Turbo Ratio/Frequency........... : 43 (4300 MHz) P-State ratio * 100 = Frequency in MHz ------------------------------------------ CPU P-States [ (12) 39 43 ] CPU C3-Cores [ 1 2 4 8 10 ] CPU C6-Cores [ 0 2 4 6 8 10 ] CPU P-States [ 12 39 41 (43) ] CPU C3-Cores [ 1 2 3 4 8 10 ] CPU P-States [ 12 36 39 41 (43) ] CPU C3-Cores [ 1 2 3 4 5 8 10 11 ] CPU P-States [ (12) 32 36 39 41 43 ] CPU C3-Cores [ 0 1 2 3 4 5 8 10 11 ] CPU C6-Cores [ 0 1 2 4 6 8 10 ] CPU P-States [ (12) 29 32 36 39 41 43 ] CPU P-States [ (12) 29 32 36 39 40 41 43 ] CPU P-States [ 12 25 29 32 36 39 40 41 (43) ] CPU C6-Cores [ 0 1 2 4 6 8 9 10 ] CPU P-States [ (12) 25 29 32 35 36 39 40 41 43 ] CPU P-States [ 12 25 29 31 32 35 36 39 40 41 (43) ] CPU C6-Cores [ 0 1 2 4 6 7 8 9 10 ] CPU P-States [ (12) 23 25 29 31 32 35 36 39 40 41 43 ] CPU P-States [ 12 23 25 29 30 31 32 35 36 39 40 41 (43) ] CPU P-States [ 12 21 23 25 29 30 31 32 (33) 35 36 39 40 41 43 ] CPU P-States [ (12) 21 23 25 28 29 30 31 32 33 35 36 39 40 41 43 ] CPU P-States [ (12) 21 23 25 28 29 30 31 32 33 34 35 36 39 40 41 43 ] CPU P-States [ (12) 18 21 23 25 28 29 30 31 32 33 34 35 36 39 40 41 43 ] CPU C3-Cores [ 0 1 2 3 4 5 8 9 10 11 ] CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 ] CPU P-States [ 12 18 21 23 25 26 28 29 30 31 32 (33) 34 35 36 39 40 41 43 ] CPU P-States [ (12) 18 21 22 23 25 26 28 29 30 31 32 33 34 35 36 39 40 41 43 ] CPU P-States [ (12) 18 21 22 23 24 25 26 28 29 30 31 32 33 34 35 36 39 40 41 43 ] CPU P-States [ (12) 18 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 39 40 41 43 ] OC.zip Edited May 9, 2020 by olmirror 1 Link to comment Share on other sites More sharing options...
eSaF Posted May 9, 2020 Share Posted May 9, 2020 14 minutes ago, olmirror said: After having played around with opencore for about a week I have it running on my hackintosh/10.14.6 (X99-UD4, 5820k, vega64). It took me quite some browsing in order to figure out how to enable XCPM and finally got it running, it's actually easier to set up than in clover and much better. Geekbench scores are low but with PMDrvr.kext scores are considerably higher and where they should be. (Same with clover and have no idea why.) But what I would like to ask why I get a 'Clover hw.busfrequency error detected : 17d78400' warning? Is this cosmetic as my system seems to be running stable? In clover there is a QPI setting that can be set to 100 which I can't find in Opencore. Is this related? Anyway I uploaded my Efi files and was hoping someone could either take a look or have some suggestions. Any pointers in the right direction are greatly appreciated. And I also wanted to use this opportunity to thank all the people who have made Opencore happen! Your hard work and patience in helping this community out is astounding... nmano, with your posts all over the internet I wouldn't be near to having my setup run as it does! Thanks bro... AppleIntelInfo.kext v3.0 Copyright © 2012-2017 Pike R. Alpha. All rights reserved. Settings: ------------------------------------------ enableHWP............................... : 0 logMSRs................................. : 1 logIGPU................................. : 0 logIntelRegs............................ : 0 logCStates.............................. : 1 logIPGStyle............................. : 1 Warning: Clover hw.busfrequency error detected : 17d78400 InitialTSC.............................. : 0xb8634dc17fbb (6143 MHz) MWAIT C-States.......................... : 8480 Processor Brandstring................... : Intel(R) Core(TM) i7-5820K CPU @ 3.30GHz Processor Signature..................... : 0x306F2 ------------------------------------------ - Family............................... : 6 - Stepping............................. : 2 - Model................................ : 0x3F (63) Model Specific Registers (MSRs) ------------------------------------------ MSR_IA32_PLATFORM_ID..............(0x17) : 0x8000000000000 ------------------------------------------ - Processor Flags...................... : 2 MSR_CORE_THREAD_COUNT.............(0x35) : 0x6000C ------------------------------------------ - Core Count........................... : 6 - Thread Count......................... : 12 MSR_PLATFORM_INFO.................(0xCE) : 0x20080C3BF3812100 ------------------------------------------ - Maximum Non-Turbo Ratio.............. : 0x21 (3300 MHz) - Ratio Limit for Turbo Mode........... : 1 (programmable) - TDP Limit for Turbo Mode............. : 1 (programmable) - Low Power Mode Support............... : 1 (LPM supported) - Number of ConfigTDP Levels........... : 1 (additional TDP level(s) available) - Maximum Efficiency Ratio............. : 12 - Minimum Operating Ratio.............. : 8 MSR_PMG_CST_CONFIG_CONTROL........(0xE2) : 0x1E000005 ------------------------------------------ - I/O MWAIT Redirection Enable......... : 0 (not enabled) - CFG Lock............................. : 0 (MSR not locked) - C3 State Auto Demotion............... : 1 (enabled) - C1 State Auto Demotion............... : 1 (enabled) - C3 State Undemotion.................. : 1 (enabled) - C1 State Undemotion.................. : 1 (enabled) - Package C-State Auto Demotion........ : 0 (disabled/unsupported) - Package C-State Undemotion........... : 0 (disabled/unsupported) MSR_PMG_IO_CAPTURE_BASE...........(0xE4) : 0x10414 ------------------------------------------ - LVL_2 Base Address................... : 0x414 - C-state Range........................ : 1 (C-States not included, I/O MWAIT redirection not enabled) IA32_MPERF........................(0xE7) : 0x21898E33CC IA32_APERF........................(0xE8) : 0x2C359BEE5F MSR_FLEX_RATIO...................(0x194) : 0xE0000 ------------------------------------------ MSR_IA32_PERF_STATUS.............(0x198) : 0x27FF00002B00 ------------------------------------------ - Current Performance State Value...... : 0x2B00 (4300 MHz) MSR_IA32_PERF_CONTROL............(0x199) : 0x2B00 ------------------------------------------ - Target performance State Value....... : 0x2B00 (4300 MHz) - Intel Dynamic Acceleration........... : 0 (IDA engaged) IA32_CLOCK_MODULATION............(0x19A) : 0x0 IA32_THERM_INTERRUPT.............(0x19B) : 0x0 IA32_THERM_STATUS................(0x19C) : 0x88370000 ------------------------------------------ - Thermal Status....................... : 0 - Thermal Log.......................... : 0 - PROCHOT # or FORCEPR# event.......... : 0 - PROCHOT # or FORCEPR# log............ : 0 - Critical Temperature Status.......... : 0 - Critical Temperature log............. : 0 - Thermal Threshold #1 Status.......... : 0 - Thermal Threshold #1 log............. : 0 - Thermal Threshold #2 Status.......... : 0 - Thermal Threshold #2 log............. : 0 - Power Limitation Status.............. : 0 - Power Limitation log................. : 0 - Current Limit Status................. : 0 - Current Limit log.................... : 0 - Cross Domain Limit Status............ : 0 - Cross Domain Limit log............... : 0 - Digital Readout...................... : 55 - Resolution in Degrees Celsius........ : 1 - Reading Valid........................ : 1 (valid) MSR_THERM2_CTL...................(0x19D) : 0x0 IA32_MISC_ENABLES................(0x1A0) : 0x850089 ------------------------------------------ - Fast-Strings......................... : 1 (enabled) - FOPCODE compatibility mode Enable.... : 0 - Automatic Thermal Control Circuit.... : 1 (enabled) - Split-lock Disable................... : 0 - Performance Monitoring............... : 1 (available) - Bus Lock On Cache Line Splits Disable : 0 - Hardware prefetch Disable............ : 0 - Processor Event Based Sampling....... : 0 (PEBS supported) - GV1/2 legacy Enable.................. : 0 - Enhanced Intel SpeedStep Technology.. : 1 (enabled) - MONITOR FSM.......................... : 1 (MONITOR/MWAIT supported) - Adjacent sector prefetch Disable..... : 0 - CFG Lock............................. : 0 (MSR not locked) - xTPR Message Disable................. : 1 (disabled) MSR_TEMPERATURE_TARGET...........(0x1A2) : 0x5E0A00 ------------------------------------------ - Turbo Attenuation Units.............. : 0 - Temperature Target................... : 94 - TCC Activation Offset................ : 0 MSR_MISC_PWR_MGMT................(0x1AA) : 0x400000 ------------------------------------------ - EIST Hardware Coordination........... : 0 (hardware coordination enabled) - Energy/Performance Bias support...... : 1 - Energy/Performance Bias.............. : 0 (disabled/MSR not visible to software) - Thermal Interrupt Coordination Enable : 1 (thermal interrupt routed to all cores) - SpeedShift Technology Enable......... : 0 (disabled) - SpeedShift Interrupt Coordination.... : 0 (disabled) - SpeedShift Energy Efficient Perf..... : 0 (disabled) - SpeedShift Technology Setup for HWP.. : No (not setup for HWP) MSR_TURBO_RATIO_LIMIT............(0x1AD) : 0x22222B2B2B2B2B2B ------------------------------------------ - Maximum Ratio Limit for C01.......... : 2B (4300 MHz) - Maximum Ratio Limit for C02.......... : 2B (4300 MHz) - Maximum Ratio Limit for C03.......... : 2B (4300 MHz) - Maximum Ratio Limit for C04.......... : 2B (4300 MHz) - Maximum Ratio Limit for C05.......... : 2B (4300 MHz) - Maximum Ratio Limit for C06.......... : 2B (4300 MHz) IA32_ENERGY_PERF_BIAS............(0x1B0) : 0x0 MSR_POWER_CTL....................(0x1FC) : 0x2104005B ------------------------------------------ - Bi-Directional Processor Hot......... : 1 (enabled) - C1E Enable........................... : 1 (enabled) MSR_RAPL_POWER_UNIT..............(0x606) : 0xA0E03 ------------------------------------------ - Power Units.......................... : 3 (1/8 Watt) - Energy Status Units.................. : 14 (61 micro-Joules) - Time Units .......................... : 10 (976.6 micro-Seconds) MSR_PKG_POWER_LIMIT..............(0x610) : 0x7FFD00014EA82 ------------------------------------------ - Package Power Limit #1............... : 3408 Watt - Enable Power Limit #1................ : 1 (enabled) - Package Clamping Limitation #1....... : 0 (disabled) - Time Window for Power Limit #1....... : 10 (2560 milli-Seconds) - Package Power Limit #2............... : 4090 Watt - Enable Power Limit #2................ : 1 (enabled) - Package Clamping Limitation #2....... : 1 (allow going below OS-requested P/T state setting Time Window for Power Limit #2) - Time Window for Power Limit #2....... : 3 (20 milli-Seconds) - Lock................................. : 0 (MSR not locked) MSR_PKG_ENERGY_STATUS............(0x611) : 0x3B2E59B ------------------------------------------ - Total Energy Consumed................ : 3787 Joules (Watt = Joules / seconds) MSR_CONFIG_TDP_NOMINAL...........(0x648) : 0x21 MSR_CONFIG_TDP_LEVEL1............(0x649) : 0x940000001E0460 MSR_CONFIG_TDP_LEVEL2............(0x64a) : 0x94000000000000 MSR_CONFIG_TDP_CONTROL...........(0x64b) : 0x0 MSR_TURBO_ACTIVATION_RATIO.......(0x64c) : 0x0 MSR_PKGC3_IRTL...................(0x60a) : 0x0 MSR_PKGC6_IRTL...................(0x60b) : 0x0 MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x1A99BDCBB MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0 MSR_PKG_C2_RESIDENCY.............(0x60d) : 0x1A99BDCBB MSR_PKG_C3_RESIDENCY.............(0x3f8) : 0x0 MSR_PKG_C6_RESIDENCY.............(0x3f9) : 0x6580D9784 IA32_TSC_DEADLINE................(0x6E0) : 0xB8635998ABC0 CPU Ratio Info: ------------------------------------------ Base Clock Frequency (BLCK)............. : 100 MHz Maximum Efficiency Ratio/Frequency...... : 12 (1200 MHz) Maximum non-Turbo Ratio/Frequency....... : 33 (3300 MHz) Maximum Turbo Ratio/Frequency........... : 43 (4300 MHz) P-State ratio * 100 = Frequency in MHz ------------------------------------------ CPU P-States [ (12) 39 43 ] CPU C3-Cores [ 1 2 4 8 10 ] CPU C6-Cores [ 0 2 4 6 8 10 ] CPU P-States [ 12 39 41 (43) ] CPU C3-Cores [ 1 2 3 4 8 10 ] CPU P-States [ 12 36 39 41 (43) ] CPU C3-Cores [ 1 2 3 4 5 8 10 11 ] CPU P-States [ (12) 32 36 39 41 43 ] CPU C3-Cores [ 0 1 2 3 4 5 8 10 11 ] CPU C6-Cores [ 0 1 2 4 6 8 10 ] CPU P-States [ (12) 29 32 36 39 41 43 ] CPU P-States [ (12) 29 32 36 39 40 41 43 ] CPU P-States [ 12 25 29 32 36 39 40 41 (43) ] CPU C6-Cores [ 0 1 2 4 6 8 9 10 ] CPU P-States [ (12) 25 29 32 35 36 39 40 41 43 ] CPU P-States [ 12 25 29 31 32 35 36 39 40 41 (43) ] CPU C6-Cores [ 0 1 2 4 6 7 8 9 10 ] CPU P-States [ (12) 23 25 29 31 32 35 36 39 40 41 43 ] CPU P-States [ 12 23 25 29 30 31 32 35 36 39 40 41 (43) ] CPU P-States [ 12 21 23 25 29 30 31 32 (33) 35 36 39 40 41 43 ] CPU P-States [ (12) 21 23 25 28 29 30 31 32 33 35 36 39 40 41 43 ] CPU P-States [ (12) 21 23 25 28 29 30 31 32 33 34 35 36 39 40 41 43 ] CPU P-States [ (12) 18 21 23 25 28 29 30 31 32 33 34 35 36 39 40 41 43 ] CPU C3-Cores [ 0 1 2 3 4 5 8 9 10 11 ] CPU C6-Cores [ 0 1 2 3 4 6 7 8 9 10 ] CPU P-States [ 12 18 21 23 25 26 28 29 30 31 32 (33) 34 35 36 39 40 41 43 ] CPU P-States [ (12) 18 21 22 23 25 26 28 29 30 31 32 33 34 35 36 39 40 41 43 ] CPU P-States [ (12) 18 21 22 23 24 25 26 28 29 30 31 32 33 34 35 36 39 40 41 43 ] CPU P-States [ (12) 18 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 39 40 41 43 ] OC.zip I am strictly a newbie at the OC game, but looking at your EFI Folder are all those SSDT Files necessary? if they are I am definitely doing something wrong and to my mind, my installs (both OC versions are running rock solid) but as the saying goes 'Every Man to his Own' 2 Link to comment Share on other sites More sharing options...
insanefrancis Posted May 9, 2020 Share Posted May 9, 2020 Hello, Do I need the Debug version of OC to have Boot chime working? Link to comment Share on other sites More sharing options...
eSaF Posted May 9, 2020 Share Posted May 9, 2020 7 minutes ago, insanefrancis said: Hello, Do I need the Debug version of OC to have Boot chime working? No not really. Link to comment Share on other sites More sharing options...
insanefrancis Posted May 9, 2020 Share Posted May 9, 2020 (edited) 12 minutes ago, eSaF said: No not really. Cool. Thanks. I was following the guide on Reddit and it was a requirement listed. Maybe it's just needed to get some audio properties. Edited May 9, 2020 by insanefrancis Link to comment Share on other sites More sharing options...
eSaF Posted May 9, 2020 Share Posted May 9, 2020 I have it working properly on both released versions, official OC and NDK's fork of OC. There are quite a few conflicting methods floating around, just follow the official OC Guide for the feature. Good luck. 1 Link to comment Share on other sites More sharing options...
olmirror Posted May 9, 2020 Share Posted May 9, 2020 (edited) Thanks for your input eSaF, i disabled all the ssdt's in the acpi folder, including the ssdt-pm/plug/ec and still get the exact same results. Seems like I don't need this with AppleXcpmEcxtraMsrs enabled in order for powermanagment to work properly. The other dsdt's I found on one of nmano's posts for X99 motherboards and are mainly for cosmetic reasons. So, something else must be casuing this error. But again, since everything appears to be working I wonder whether or not I should worry about it... Edited May 9, 2020 by olmirror Link to comment Share on other sites More sharing options...
eSaF Posted May 9, 2020 Share Posted May 9, 2020 16 minutes ago, olmirror said: Thanks for your input eSaF, i disabled all the ssdt's in the acpi folder, including the ssdt-pm/plug/ec and still get the exact same results. Seems like I don't need this with AppleXcpmEcxtraMsrs enabled in order for powermanagment to work properly. The other dsdt's I found on one of nmano's posts for X99 motherboards and are mainly for cosmetic reasons. So, something else must be casuing this error. But again, since everything appears to be working I wonder whether or not I should worry about it... I don't know about OC on a X99 board but I do know the concept of OC is to run as light weight and vanilla as possible like a real Mac. Any error is a cause for concern for future proofing your system towards future upgrades. To my untrained eye your folder and config.plist is in need of a clean up, I would search and see what others on a X99 Platform is implementing to get their rig running stable without so much luggage. Good luck. Link to comment Share on other sites More sharing options...
Synapsis Posted May 9, 2020 Share Posted May 9, 2020 Hello everyone, I don't know what I do wrong :-( I simply can't get pass the login screen freaking macOS login screen ;-/ My hardware shouldnt be the problem. I tried iMac19,1 iMac19,2 iMacPro1,1 SMBioses, Tried different -igfx flags Tried different -agpmod flags - only result is when disabled iGPU works, RX VEGA won't I can boot with both GFX/iGPU initialized, I can the mouse around screens, but they remain black, and that's it. Im getting really frustrated here :-( I run on default OC sample config, tweak accordingly to match my config as starting point. My configur - CPU: i7-8700K - GPU: Asrock RX Vega 56 8GB - MB: Asus z370-P Prime - 1 4K UHD DP connected screen - 1 HD 1080p connected screen Added HPET patches from SSDTTime and 2 line Device for the iGPU and that's it. If I set the iGPU as the first GPU - macOS initializes, the bar below logo almost completes and black screen or a totally dark catalina background and the freeze If I set the GPU as the first GPU (with iGPU driving screen) - macOS freezes right or before logging in, evertyrthings looks ok till this point BUT mouse gets choppy, and after a 30 seconds it craps totally or reboots... If I set the GPU as the only GPU (no iGPU driving screen) i freeze on the login screen... WTF??! Only half-a**sed config that works is with the iGPU and -agdpmod=none, then macOS works fine but I got only one screen and no AMD Vega. Never had problems with the GPU but now it's unusable. Please, can someone point my into right direction? Thanks in advance. Link to comment Share on other sites More sharing options...
MacNB Posted May 9, 2020 Share Posted May 9, 2020 2 hours ago, olmirror said: Thanks for your input eSaF, i disabled all the ssdt's in the acpi folder, including the ssdt-pm/plug/ec and still get the exact same results. Seems like I don't need this with AppleXcpmEcxtraMsrs enabled in order for powermanagment to work properly. The other dsdt's I found on one of nmano's posts for X99 motherboards and are mainly for cosmetic reasons. So, something else must be casuing this error. But again, since everything appears to be working I wonder whether or not I should worry about it... I would not assume it is an OC problem. The fact that AppleIntelInfo.kext reports "Clover....." means it is assuming Clover set those HW bus frequency which is incorrect as it is not detecting the boot loader. It could be that it is calculating the the values incorrectly. Remember Piker Alpha did all that great work a long time ago and many CPU's and chipsets have come along since his work and he is no longer maintaining that kext. You should report the issue at the source where you got that kext and see what they suggest. Link to comment Share on other sites More sharing options...
shhbz Posted May 9, 2020 Share Posted May 9, 2020 (edited) On 5/8/2020 at 2:38 AM, shhbz said: Hi I wonder if someone can share some idea on what's wrong on my Catalina built. Issue 1. Catalina on Opencore 0.5.8 does not restart or shutdown, it blinks the screen once and stays on the homescreen Catalina Dekstop. Issue 2. PROXITY_WAKE=1 so how to change to 0 as i did it with terminal command sudo pmset -a proximitywake 0 but on reboot it reset itself back to 1, so when I try to wake the pc from sleep using wireless mouse mx master 2s it does not wake up.the CPU turns on but not the screen. Config: MSI Z170krait Gaming3x ,6700k Skylake, 32gb Gskill, Sapphire Rx 580 Attaching below my Opencore EFI and Energy Saver settings EFI.zip Hey i wondered as what can be done, 3 days of try and still unable to figure out intel usb mapping and fixing restart/shutdown fix and i try to solve it but to no result can anyone help me on this the as i am not aware how to do dsdt patch and what needs to be done. Beside the two issue all runs fine, looking for a solution if anyone can help me with misc fixes here https://dortania.github.io/USB-Map-Guide/intel-mapping/intel.html 1.USB Mapping done limit to 15ports 2.MISC fixes (cant solve) 3.I use Wireless mouse keyboard connected using bluetooth so it needs to be configured to wake using the same Sent from my iPhone using Tapatalk DSDT.aml Edited May 9, 2020 by shhbz Link to comment Share on other sites More sharing options...
rottenpants Posted May 9, 2020 Share Posted May 9, 2020 I'm trying to boot OC on my Toshiba laptop but it doesn't even show the picker menu, it just hangs on the laptop logo with the following text: 00:000 00:000 OC: OpenCore DBG-058-2020-05-04 is loading in Optional mode (0/0)... 00:075 00:075 OC: Boot timestamp - 2020.05.09 20:51:23 00:143 00:067 OCCPU: MP services threads 4 (enabled 4) - Success 00:211 00:067 OCCPU: MP services Pkg 1 Cores 2 Threads 2 - Success 00:279 00:068 OCCPU: Found Intel(R) Core(TM) i7-5500U CPU @ 2.40GHz 00:347 00:067 OCCPU: Signature 306D4 Stepping 4 Model 3D Family 6 Type 0 ExtModel 3 ExtFamily 0 uCode 2A 00:415 00:068 OCCPU: Detected Apple Processor Type: 07 -> 0706 00:486 00:070 OCCPU: Ratio Min 5 Max 24 Current 23 Turbo 30 29 29 29 00:555 00:068 OCCPU: Timer address is 1808 from LPC 00:723 00:168 OCCPU: CPUFrequencyFromTSC 2394455384Hz 2394MHz 00:791 00:067 OCCPU: CPUFrequency 2394455384Hz 2394MHz 00:858 00:067 OCCPU: FSBFrequency 99768974Hz 99MHz 00:927 00:068 OCCPU: Pkg 1 Cores 2 Threads 4 00:995 00:067 OC: OcLoadNvramSupport... 01:063 00:068 OC: Not deleting NVRAM 4D1EDE05-38C7-4A6A-9CC6-4BCCA8B38C14:UIScale, matches add 01:132 00:068 OC: Not deleting NVRAM 4D1EDE05-38C7-4A6A-9CC6-4BCCA8B38C14:DefaultBackgroundColor, matches add 01:209 00:076 OC: Deleting NVRAM 4D1FDA02-38C7-4A6A-9CC6-4BCCA8B30102:rtc-blacklist - Not Found 01:277 00:068 OC: Not deleting NVRAM 7C436110-AB2A-4BBB-A880-FE41995C9F82:boot-args, matches add 01:345 00:068 OC: Setting NVRAM 4D1EDE05-38C7-4A6A-9CC6-4BCCA8B38C14:DefaultBackgroundColor - ignored, exists 01:462 00:116 OC: Setting NVRAM 4D1EDE05-38C7-4A6A-9CC6-4BCCA8B38C14:UIScale - ignored, exists 01:550 00:088 OC: Setting NVRAM 4D1FDA02-38C7-4A6A-9CC6-4BCCA8B30102:rtc-blacklist - Not Found 01:654 00:103 OC: Setting NVRAM 7C436110-AB2A-4BBB-A880-FE41995C9F82:SystemAudioVolume - ignored, exists 01:731 00:076 OC: Setting NVRAM 7C436110-AB2A-4BBB-A880-FE41995C9F82:boot-args - ignored, exists 01:840 00:109 OC: Setting NVRAM 7C436110-AB2A-4BBB-A880-FE41995C9F82:csr-active-config - ignored, exists 01:918 00:077 OC: Setting NVRAM 7C436110-AB2A-4BBB-A880-FE41995C9F82:prev-lang:kbd - ignored, exists 01:998 00:080 OC: Current version is DBG-058-2020-05-04 02:082 00:083 OC: OcLoadUefiSupport... 02:160 00:077 OCSMC: Initial key obtain failure - Not Found 02:245 00:084 OCSMC: Failed to remove key - Not Found 02:331 00:086 OCRTC: Wake log is 0x00 0xE1 162 0xF7 02:407 00:076 AIFTimerBoostInit Current timer is 549254 02:482 00:074 AIFTimerBoostInit changed period 549254 to 50000 02:562 00:080 AmiEfiKeycodeProtocol is unavailable on gST->ConsoleHandle - Unsupported 02:638 00:075 EfiSimpleTextInputExProtocol is unavailable on gST->ConsoleHandle - Unsupported 02:822 00:183 gST->ConIn D6446E00 vs found D6446E00 From what understand the problem might be in the last lines, specifically: 02:562 00:080 AmiEfiKeycodeProtocol is unavailable on gST->ConsoleHandle - Unsupported 02:638 00:075 EfiSimpleTextInputExProtocol is unavailable on gST->ConsoleHandle - Unsupported I tried using all 4 output modes (BuiltinGraphics, SystemGraphics, SystemText and SystemGeneric), I also played around with ProvideConsoleGop, ReplaceTabWithSpace and Resolution but it always shows the same errors. Does anyone have an idea on what's going on? Lapotp specs: Toshiba Kira 107 CPU: i7 5500u (Broadwell) GPU: HD5500 8GB RAM DW1560 wifi/bt card Using latest Bios Thanks in advance EFI.zip DSDT.aml Link to comment Share on other sites More sharing options...
olmirror Posted May 9, 2020 Share Posted May 9, 2020 19 minutes ago, MacNB said: I would not assume it is an OC problem. The fact that AppleIntelInfo.kext reports "Clover....." means it is assuming Clover set those HW bus frequency which is incorrect as it is not detecting the boot loader. It could be that it is calculating the the values incorrectly. Remember Piker Alpha did all that great work a long time ago and many CPU's and chipsets have come along since his work and he is no longer maintaining that kext. You should report the issue at the source where you got that kext and see what they suggest. Appreciate your input MacNB, I was already wondering about that since I'm not using clover. I also tried to boot without PMDrvr.kext (just in case) and am getting the same error message, but lower benchmark scores. I also have a separate disk with Catalina that gives me the exact same readings as in Mojave when I boot with a seperate config with the corresponding xcmp kernel patches. From where could clover still be injecting that information into my system? Link to comment Share on other sites More sharing options...
Maf3r0 Posted May 9, 2020 Share Posted May 9, 2020 21 hours ago, Matgen84 said: I suppose. Just like that! Link to comment Share on other sites More sharing options...
Maf3r0 Posted May 9, 2020 Share Posted May 9, 2020 Seems that Misc/Security/AllowSetDefault=Yes not work yet with OpenCanopy.efi (External picker). it would be great if could be added (or fixed) in future releases. Link to comment Share on other sites More sharing options...
vit9696 Posted May 9, 2020 Share Posted May 9, 2020 @rottenpants the issue is probably with Input configuration. I would suggest you check all values there, but my first thought is that TimerResolution might be too high for your system. Link to comment Share on other sites More sharing options...
Andrey1970 Posted May 9, 2020 Share Posted May 9, 2020 7 minutes ago, Maf3r0 said: Seems that Misc/Security/AllowSetDefault=Yes not work yet with OpenCanopy.efi (External picker). it would be great if could be added (or fixed) in future releases. Hot keys not implemented in OpenCanopy. 1 1 Link to comment Share on other sites More sharing options...
rottenpants Posted May 9, 2020 Share Posted May 9, 2020 (edited) 32 minutes ago, vit9696 said: @rottenpants the issue is probably with Input configuration. I would suggest you check all values there, but my first thought is that TimerResolution might be too high for your system. Thank you for responding What value should I put in TimerResolution? Edit: Changed KeySupportMode to V2 and now the boot menu appears Edited May 9, 2020 by rottenpants Link to comment Share on other sites More sharing options...
MacNB Posted May 9, 2020 Share Posted May 9, 2020 1 hour ago, olmirror said: Appreciate your input MacNB, I was already wondering about that since I'm not using clover. I also tried to boot without PMDrvr.kext (just in case) and am getting the same error message, but lower benchmark scores. I also have a separate disk with Catalina that gives me the exact same readings as in Mojave when I boot with a seperate config with the corresponding xcmp kernel patches. From where could clover still be injecting that information into my system? Clover is NOT injecting anything as Clover is not the boot loader. Like I said, the AppleIntelInfo.kext is HARDCODED with the comment about Clover (it is ASSUMING people always boot from Clover). What I am suggesting is that it is a bug with that kext. If you still have a Clover boot loader handy, you can boot your system off that Clover and check if you still get that "error". I bet you the you will see it with Clover too. Link to comment Share on other sites More sharing options...
iFrodo Posted May 9, 2020 Share Posted May 9, 2020 (edited) I was been using OpenCore up to 0.5.3 successfully on my setup, with FileVault 2 enabled. But it stopped working since 0.5.4 release and still not work with latest 0.5.8 release. I get to the FileVault 2 password screen successfully and can enter my password correctly, but then some debug lines appear and nothing else, it doesn't seem that the macOS kernel is started at all. Find attached a shot of debug lines, as well as config tested (one is my working 0.5.3 config, the others are rewritten from scratch configs tries) My computer: - Gigabyte GA-Z87N-WIFI (rev. 1.x) - AW-CE123H 802.11ac/nbg WiFi+BT Broadcom BCM4352 867Mbps mini-PCIe card - Intel Core i7 4770k (not overclocked) - AMD Vega 56 8GB - 16GB RAM - SSD drive (from Crucial) with APFS macOS partition Any idea what could be the problem ? config.plist config_previous.plist config.053.plist Edited May 9, 2020 by iFrodo Link to comment Share on other sites More sharing options...
topolino1 Posted May 9, 2020 Share Posted May 9, 2020 (edited) 26 minutes ago, iFrodo said: I was been using OpenCore up to 0.5.3 successfully on my setup, with FileVault 2 enabled. But it stopped working since 0.5.4 release and still not work with latest 0.5.8 release. I get to the FileVault 2 password screen successfully and can enter my password correctly, but then some debug lines appear and nothing else, it doesn't seem that the macOS kernel is started at all. Find attached a shot of debug lines, as well as config tested (one is my working 0.5.3 config, the others are rewritten from scratch configs tries) My computer: - Gigabyte GA-Z87N-WIFI (rev. 1.x) - AW-CE123H 802.11ac/nbg WiFi+BT Broadcom BCM4352 867Mbps mini-PCIe card - Intel Core i7 4770k (not overclocked) - AMD Vega 56 8GB - 16GB RAM - SSD drive (from Crucial) with APFS macOS partition Any idea what could be the problem ? config.plist config_previous.plist config.053.plist Everyone says that from 10.15.4 it's normal. I have it too, but the computer starts and works. Edited May 9, 2020 by topolino1 Link to comment Share on other sites More sharing options...
Recommended Posts