Locked Down Posted February 18, 2021 Share Posted February 18, 2021 1 hour ago, kernel_void said: @AudioGod I am using efi 19.1 to install big sur but it restarts on install I have installed the latest 11L bios and am using your bios config correctly. What can it be? ps: I'm using the processor's integrated video card, I don't have an external one Have you removed the agdpmod=pikera from the config file, as that is for certain amd graphics cards, which you don't have? Link to comment Share on other sites More sharing options...
AudioGod Posted February 18, 2021 Author Share Posted February 18, 2021 @kernel_void You need to set up the igpu correctly and also patch it to work via device properties. See here, https://dortania.github.io/OpenCore-Install-Guide/config.plist/coffee-lake.html#deviceproperties And here, https://github.com/acidanthera/WhateverGreen/blob/master/Manual/FAQ.IntelHD.en.md Link to comment Share on other sites More sharing options...
AudioGod Posted March 1, 2021 Author Share Posted March 1, 2021 (edited) OpenCore 0.6.7 EFI Update (Big Sur 11.3 Ready), 1st March 2021 (Use With Bios Revision F11L or Newer) The EFIs and DSDTs have now been updated to the my latest versions. Changes made include, Lilu 1.5.1 AppleALC 1.5.8, WhateverGreen 1.4.8, VirtualSMC 1.2.1, OpenCore Updated to Revision 0.6.7 (Big Sur 11.3 Ready), New OpenCanopy Icons OpenCanopy is Enabled as Standard, New OpenCanopy Icons Plus other minor tweaks and changes to all of the configs. OpenCore EFI Update v0.6.7 - 01/03/2021 OC 067 1,1 Z390 Master EFI 010321.zip - OpenCore v0.6.7, SMBios iMacPro1,1 (IGPU Disabled) OC 067 19,1 Z390 Master EFI 010321.zip - OpenCore v0.6.7, SMBios iMac19,1 IMPORTANT - OPENCORE HAS CHANGED THE WAY THE BOOTSTRAP WORKS SO YOU WILL NEED TO RESELECT YOUR BIG SUR DISK (F12 DISK SELECT OR FROM WITHIN THE BIOS) AND THEN RESET YOUR NVRAM BEFORE BOOTING INTO THE NEW EFI FOR THE FIRST TIME, THIS IS VITAL. Note - If your not using a 5700 XT or any other Navi GPU then remove agdpmod=pikera from the boot arguments. Note 2 - Do not try to carry across your old OpenCore Config.plist to the new EFI as to many changes have occurred in 0.6.0. Use the new Config.plist instead. For OpenCore Using PlistEdit Pro add your details by modifying the following PLEASE NOTE - These EFIs are setup to be used with your msr Unlocked so make sure you use the correct bios settings listed below or use the F11L Unlocked Profile I have provided. Additional Downloads Z390AORUSMASTER.F11l.zip - Aorus Z390 Master Bios Firmware F11L PlistEdit Pro.zip - PlistEdit Pro (use to edit OpenCore) PLEASE NOTE - MSR Unlock is now baked into the BIOS as a setting so you no longer need my bios profile to unlock your MSR. BIOS SETTINGS (Bios Revision F11L) • Enter BIOS -> Press Delete -> Enter Setup • Save & Exit -> Load Optimized Defaults • Boot -> CFG Lock -> Disabled • Boot -> Windows 8/10 Features -> Win 8/10 WHQL • Boot -> CSM Support -> Disabled (Can be set to Enabled if need be but try to have it set to Disabled first) • Favourites -> Extreme Memory Profile (X.M.P.) -> Profile1 • Favourites -> VT-d -> Disabled (Can be set to Enabled or Disabled, Your choice) • Settings -> IO Ports -> Internal Display Output -> PCIe 1 Slot • Settings -> IO Ports -> Internal Graphics -> Enabled (Disabled If Using SMBios 1,1) • Settings -> IO Ports -> DVMT Pre-Allocated -> 64M • Settings -> IO Ports -> DVMT Total GFX0-Allocated -> 256M • Settings -> IO Ports -> Aperture Size -> 256MB• Settings -> IO Ports -> Wifi -> Disabled • Settings -> IO Ports -> Audio Controller -> Enabled • Settings -> IO Ports -> Above 4G Decoding -> Enabled • Settings -> IO Ports -> Super IO Configuration -> Serial Port -> Disabled • Settings -> IO Ports -> USB Configuration -> Legacy USB Support -> Auto • Settings -> IO Ports -> USB Configuration -> XHCI Hands-off -> Enabled • Settings -> Miscellaneous -> Software Guard Extensions (SGX) -> Disabled • Settings -> Platform Power -> Platform Power Management -> Enabled • Settings -> Platform Power -> ErP -> Enabled • Settings -> Platform Power -> RC6(Render Standby) -> Enabled • Save & Exit → Save & Exit Setup Edited March 1, 2021 by AudioGod 3 6 Link to comment Share on other sites More sharing options...
gibbo592 Posted March 6, 2021 Share Posted March 6, 2021 Thanks for your time and effort appreciated 1 Link to comment Share on other sites More sharing options...
kunyi Posted March 7, 2021 Share Posted March 7, 2021 Szia. Ez a wifi kártya jó lehet az alaplap számára? Vettem egyet, de az alaplappal nem működik. Természetesen a BIOS-ban engedélyeztem. https://www.aliexpress.com/item/1005001942016268.html?spm=a2g0s.9042311.0.0.452a4c4dc7Xh98 Link to comment Share on other sites More sharing options...
AudioGod Posted March 7, 2021 Author Share Posted March 7, 2021 (edited) 9 minutes ago, kunyi said: Szia. Ez a wifi kártya jó lehet az alaplap számára? Vettem egyet, de az alaplappal nem működik. Természetesen a BIOS-ban engedélyeztem. https://www.aliexpress.com/item/1005001942016268.html?spm=a2g0s.9042311.0.0.452a4c4dc7Xh98 Ez az egyik működik, de gondja, hogy megfelelően működjön. Szerezd meg inkább ezt, és gond nélkül működik a dobozból https://www.aliexpress.com/item/4001204844699.html?spm=a2g0o.productlist.0.0.3fb32081CXrMB3&algo_pvid=aa880fdf-875d-450e-9dba-d47c3309072d&algo_expid=aa880fdf-875d-450e-9dba-d47c3309072d-1&btsid=2100bddd16151561105401216e1c3c&ws_ab_test=searchweb0_0,searchweb201602_,searchweb201603_ az Intel-et is használhatja most ezeken az illesztőprogramokon keresztül. nem tökéletes, de remekül működik. https://github.com/OpenIntelWireless Edited March 7, 2021 by AudioGod Link to comment Share on other sites More sharing options...
kunyi Posted March 8, 2021 Share Posted March 8, 2021 Szia. Köszönöm a gyors választ. Link to comment Share on other sites More sharing options...
davidm71 Posted March 14, 2021 Share Posted March 14, 2021 Hi, Looking at your guide for inspiration. Got OpenCore 5.8, Cat 15.4, iMac 17,1 + Sapphire Nitro+ 5700XT and works as long as I'm using HDMI. Cant get Displayport working in that screen does not get past black screen. Should I try 1,1 ? Thanks Link to comment Share on other sites More sharing options...
AudioGod Posted April 5, 2021 Author Share Posted April 5, 2021 OpenCore 0.6.8 EFI Update (Big Sur 11.3 Ready), 5th April 2021 (Use With Bios Revision F11L or Newer) The EFIs and DSDTs have now been updated to the my latest versions. Changes made include, Lilu 1.5.2, AppleALC 1.5.9, WhateverGreen 1.4.9, VirtualSMC 1.2.2, OpenCore Updated to Revision 0.6.8 (Big Sur 11.3 Ready), OpenCanopy is Enabled as Standard, New OpenCanopy Icons Mouse now working in OpenCanopy Plus other minor tweaks and changes to all of the configs. OpenCore EFI Update v0.6.8 - 05/04/2021 OC 068 1,1 Z390 Master EFI.zip- OpenCore v0.6.8, SMBios iMacPro1,1 (IGPU Disabled) OC 068 19,1 Z390 Master EFI.zip- OpenCore v0.6.8, SMBios iMac19,1 Note - If your not using a 5700 XT or any other Navi GPU then remove agdpmod=pikera from the boot arguments. Note 2 - Do not try to carry across your old OpenCore Config.plist to the new EFI as to many changes have occurred in 0.6.7. Use the new Config.plist instead. For OpenCore Using PlistEdit Pro add your details by modifying the following 4 4 Link to comment Share on other sites More sharing options...
kunyi Posted April 14, 2021 Share Posted April 14, 2021 Hali. Thanks for the update. Everything is awesome. Hi: Kunyi 2 Link to comment Share on other sites More sharing options...
Locked Down Posted April 21, 2021 Share Posted April 21, 2021 So the latest beat 11.4 beta 1 now supports Big Navi cards. 3 Link to comment Share on other sites More sharing options...
AudioGod Posted April 21, 2021 Author Share Posted April 21, 2021 @Locked Down Yep, tried and tested and working well. Seems to be better with WEG disabled. 6 Link to comment Share on other sites More sharing options...
AudioGod Posted May 3, 2021 Author Share Posted May 3, 2021 OpenCore 0.6.9 EFI Update (Big Sur 11.4 Ready), 3rd May 2021 (Use With Bios Revision F11L or Newer) The EFIs and DSDTs have now been updated to the my latest versions. Changes made include, Lilu 1.5.3, AppleALC 1.6.0, IntelMausi 1.0.6, VirtualSMC 1.2.3, OpenCore Updated to Revision 0.6.9 (Big Sur 11.4 Ready), OpenCanopy is Enabled as Standard, New OpenCanopy Icons Mouse now working in OpenCanopy Plus other minor tweaks and changes to all of the configs. OpenCore EFI Update v0.6.9 - 03/05/2021 OC 069 1,1 Z390 Master EFI.zip - OpenCore v0.6.9, SMBios iMacPro1,1 (IGPU Disabled) OC 069 19,1 Z390 Master EFI.zip - OpenCore v0.6.9, SMBios iMac19,1 Note - If your not using a 5700 XT or any other Navi GPU then remove agdpmod=pikera from the boot arguments. Note 2 - Do not try to carry across your old OpenCore Config.plist to the new EFI as to many changes have occurred in 0.6.7. Use the new Config.plist instead. For OpenCore Using PlistEdit Pro add your details by modifying the following 4 Link to comment Share on other sites More sharing options...
M0r1d1n Posted May 5, 2021 Share Posted May 5, 2021 (edited) Hi, I'm going to be updating from OC 0.6.0 to 0.6.9 later today and BIOS from F11e to F11l. I have been reading through everything and this is what I have found I need to do: - make a backup of everything - update BIOS to F11l - load BIOS F11l defaults from @AudioGod - setup BIOS settings as per instructions from @AudioGod - set boot drive again - reset NVRAM (in OC picker?) - add -cdfon to bootargs to make my 4K display work properly (?) My current bootargs are: agdpmod=pikera -v -cdfon shikigva=80 darkwake=0 I am running an Intel i9-9900K + RX 5700 XT + EIZO 4K and iMac19,1 with iGPU of course. Anything else I should be aware of? Edited May 5, 2021 by M0r1d1n Link to comment Share on other sites More sharing options...
M0r1d1n Posted May 5, 2021 Share Posted May 5, 2021 3 hours ago, M0r1d1n said: Hi, I'm going to be updating from OC 0.6.0 to 0.6.9 later today and BIOS from F11e to F11l. I have been reading through everything and this is what I have found I need to do: - make a backup of everything - update BIOS to F11l - load BIOS F11l defaults from @AudioGod - setup BIOS settings as per instructions from @AudioGod - set boot drive again - reset NVRAM (in OC picker?) - add -cdfon to bootargs to make my 4K display work properly (?) My current bootargs are: agdpmod=pikera -v -cdfon shikigva=80 darkwake=0 I am running an Intel i9-9900K + RX 5700 XT + EIZO 4K and iMac19,1 with iGPU of course. Anything else I should be aware of? Updated without any problems. Didn't load BIOS defaults (not needed, my bad). Did not add -cdfon to bootargs. 2 Link to comment Share on other sites More sharing options...
ucdosjiafu Posted May 13, 2021 Share Posted May 13, 2021 Excuse me, why does my earphone have sound, but the external player has no sound? oc0.6.9 Link to comment Share on other sites More sharing options...
AudioGod Posted June 7, 2021 Author Share Posted June 7, 2021 (edited) OpenCore 0.7.0 EFI Update (Big Sur 11.6 Ready), 7th June 2021 (Use With Bios Revision F11L or Newer) The EFIs and DSDTs have now been updated to the my latest versions. Changes made include, Lilu 1.5.3, AppleALC 1.6.1, IntelMausi 1.0.6, VirtualSMC 1.2,4, WhateverGreen 1.5.0 OpenCore Updated to Revision 0.7.0 (Big Sur 11.5 Ready), SIP can now be toggled from within OpenCanopy New OpenCanopy Icons HFSPlus Updated Plus other minor tweaks and changes to all of the configs. OpenCore EFI Update v0.7.0 - 07/06/2021 OC 070 1,1 Z390 Master EFI.zip - OpenCore v0.7.0, SMBios iMacPro1,1 (IGPU Disabled) OC 070 19,1 Z390 Master EFI.zip - OpenCore v0.7.0, SMBios iMac19,1 Note - If your not using a 5700 XT or any other Navi GPU then remove agdpmod=pikera from the boot arguments. Note 2 - Do not try to carry across your old OpenCore Config.plist to the new EFI as to many changes have occurred in 0.6.7. Use the new Config.plist instead. For OpenCore Using PlistEdit Pro add your details by modifying the following Sadly this will be my last EFI update for this thread as my focus is no longer on the Intel side of life and it’s hard for me to keep up with little quirks and problems on the EFI side of life. Im still here to annoy you all though and the thread will stay alive. Enjoy and BigUps AG Edited June 7, 2021 by AudioGod 6 2 Link to comment Share on other sites More sharing options...
matt-uk Posted June 8, 2021 Share Posted June 8, 2021 (edited) 14 hours ago, AudioGod said: Sadly this will be my last EFI update for this thread as my focus is no longer on the Intel side of life and it’s hard for me to keep up with little quirks and problems on the EFI side of life. Im still here to annoy you all though and the thread will stay alive. Enjoy and BigUps AG Hey AG, Cheers for supporting for this long. Gutted there won't be any more updates but appreciate your efforts with this especially as you aren't even using this hardware any more. Do you think anyone would be wiling to take up the challenge of maintaining and upgrading the EFI for the community you have built here and on the Pro thread? All the best man - wish I could follow you over to Ryzen but I have sunk so much money into this system I have to stick with it for the next few years! Matt Edited June 8, 2021 by matt-uk 1 Link to comment Share on other sites More sharing options...
eSaF Posted June 8, 2021 Share Posted June 8, 2021 14 hours ago, AudioGod said: Sadly this will be my last EFI update for this thread as my focus is no longer on the Intel side of life and it’s hard for me to keep up with little quirks and problems on the EFI side of life. Im still here to annoy you all though and the thread will stay alive. Enjoy and BigUps AG Sad news indeed but B we all understand so don't sweat, we know you will be here upsetting the apple cart from time to time. 2 Link to comment Share on other sites More sharing options...
Benjamin Franklin Posted June 14, 2021 Share Posted June 14, 2021 (edited) Many thanks B for all you help and support, it's been much appreciated bro. On 6/8/2021 at 12:00 PM, eSaF said: Sad news indeed but B we all understand so don't sweat, we know you will be here upsetting the apple cart from time to time. And if you can spare a free moment please toss us the occasional update? Edited June 14, 2021 by Benjamin Franklin 1 Link to comment Share on other sites More sharing options...
matt-uk Posted June 25, 2021 Share Posted June 25, 2021 (edited) Anyone experienced any issues with the latest OC, EFI and MacOS update? I can't pin it down but I seem to have occasional lockups, seems to be related to monitors sleeping, or waking up or switching inputs. I can't diagnose exactly. My hack doesn't sleep but the monitors do get switched to another PC and on one occasion when I switched back after a day or so I couldn't get an image. Another time the screen seemed to freeze. On both occasions I couldn't do anything other than a hard reset, and even then holding the power button did nothing - I actually had to turn off the PSU - never had that happen before. It may be nothing but I haven't had a single issue and the system has bene rock solid so it is such a shock to have a problem now. Hope everyone is doing great! UPDATE: I just shut down MacOS to boot up windows - which I rarely do, and after what looked to be successful shut down the power switch would not work so I could not turn the system on. Once I pulled the power the button worked again. Very odd - perhaps a hardware issue? UPDATE 2: 90% sure this is a hardware issue with the power button and front I/O converter I use on my G5 case mod. Strange though as it is intermittent and did seem to coincide with switching monitor inputs and case a lockup. Thanks to those who replied below. Edited July 20, 2021 by matt-uk Link to comment Share on other sites More sharing options...
Quiggycn Posted July 1, 2021 Share Posted July 1, 2021 I am on the latest OC, EFI, and MacOS and everything runs smooth. No issues with sleep at all. I am still crossing finders that its not an hardware issue 1 1 Link to comment Share on other sites More sharing options...
Benjamin Franklin Posted July 4, 2021 Share Posted July 4, 2021 On 6/25/2021 at 6:16 PM, matt-uk said: Anyone experienced any issues with the latest OC, EFI and MacOS update? I can't pin it down but I seem to have occasional lockups, seems to be related to monitors sleeping, or waking up or switching inputs. I can't diagnose exactly. My hack doesn't sleep but the monitors do get switched to another PC and on one occasion when I switched back after a day or so I couldn't get an image. Another time the screen seemed to freeze. On both occasions I couldn't do anything other than a hard reset, and even then holding the power button did nothing - I actually had to turn off the PSU - never had that happen before. It may be nothing but I haven't had a single issue and the system has bene rock solid so it is such a shock to have a problem now. Hope everyone is doing great! UPDATE: I just shut down MacOS to boot up windows - which I rarely do, and after what looked to be successful shut down the power switch would not work so I could not turn the system on. Once I pulled the power the button worked again. Very odd - perhaps a hardware issue? Did you try resetting NVRAM? Reboot, at OC boot screen press spacebar, select reset nvram, it’ll reboot. Continue as usual. Then, remember to set your startup disk in macos settings after login. 1 Link to comment Share on other sites More sharing options...
matt-uk Posted July 20, 2021 Share Posted July 20, 2021 On 7/4/2021 at 7:58 AM, Benjamin Franklin said: Did you try resetting NVRAM? Reboot, at OC boot screen press spacebar, select reset nvram, it’ll reboot. Continue as usual. Then, remember to set your startup disk in macos settings after login. Thanks for the advice. Yes I had reset NVRAM. I do think this is a hardware issue now. I am using a converted G5 case and a converter for the original power button and I/O which I think might be causing problems although it was fine for 12 months. Appreciate you guys taking the time to comment! Link to comment Share on other sites More sharing options...
Benjamin Franklin Posted July 26, 2021 Share Posted July 26, 2021 On 6/7/2021 at 9:07 PM, AudioGod said: OpenCore 0.7.0 EFI Update (Big Sur 11.6 Ready), 7th June 2021 (Use With Bios Revision F11L or Newer) The EFIs and DSDTs have now been updated to the my latest versions. Changes made include, Lilu 1.5.3, AppleALC 1.6.1, IntelMausi 1.0.6, VirtualSMC 1.2,4, WhateverGreen 1.5.0 OpenCore Updated to Revision 0.7.0 (Big Sur 11.5 Ready), SIP can now be toggled from within OpenCanopy New OpenCanopy Icons HFSPlus Updated Plus other minor tweaks and changes to all of the configs. OpenCore EFI Update v0.7.0 - 07/06/2021 OC 070 1,1 Z390 Master EFI.zip - OpenCore v0.7.0, SMBios iMacPro1,1 (IGPU Disabled) OC 070 19,1 Z390 Master EFI.zip - OpenCore v0.7.0, SMBios iMac19,1 Note - If your not using a 5700 XT or any other Navi GPU then remove agdpmod=pikera from the boot arguments. Note 2 - Do not try to carry across your old OpenCore Config.plist to the new EFI as to many changes have occurred in 0.6.7. Use the new Config.plist instead. For OpenCore Using PlistEdit Pro add your details by modifying the following Sadly this will be my last EFI update for this thread as my focus is no longer on the Intel side of life and it’s hard for me to keep up with little quirks and problems on the EFI side of life. Im still here to annoy you all though and the thread will stay alive. Enjoy and BigUps AG Has anyone updated to 11.5 with OC 71 yet? What can you report back, can we use the same config without changes? 3 Link to comment Share on other sites More sharing options...
Recommended Posts