Benjamin Franklin Posted January 4, 2021 Share Posted January 4, 2021 On 12/27/2020 at 11:03 PM, Locked Down said: Moving forward from AG's next, and final, update to OC 0.6.5, if you want to update your own config.plist then you can use THIS tool to list changes that you need to make to your config file. You just drag your current config file and the new sample.plist file when asked at the appropriate place in the running terminal window. The tool will then list any new fields you need to add or remove or change in your config. Very simple to use and it makes sure you don't miss anything. If it's stable, can you share your config.plist (just like AG did, with removal of the serial and mobo numbers of course)? Cheers! Link to comment Share on other sites More sharing options...
AudioGod Posted January 4, 2021 Author Share Posted January 4, 2021 4 minutes ago, Benjamin Franklin said: If it's stable, can you share your config.plist (just like AG did, with removal of the serial and mobo numbers of course)? Cheers! I will post OC 065 when it releases don’t worry pal. 1 1 Link to comment Share on other sites More sharing options...
Locked Down Posted January 4, 2021 Share Posted January 4, 2021 5 hours ago, AudioGod said: I will post OC 065 when it releases don’t worry pal. OC 0.6.5 has now been released. I use the internal Bluetooth and Wifi and a few other mods to my config.plist (quad booting Catalina, Big Sur, Windows and Linux Mint) so mine isn't applicable to most on here. Link to comment Share on other sites More sharing options...
AudioGod Posted January 4, 2021 Author Share Posted January 4, 2021 1 minute ago, Locked Down said: OC 0.6.5 has now been released. I use the internal Bluetooth and Wifi and a few other mods to my config.plist (quad booting Catalina, Big Sur, Windows and Linux Mint) so mine isn't applicable to most on here. No worries pal, I’ve got it all setup and ready to post. I will do so in the next few hours. 2 Link to comment Share on other sites More sharing options...
AudioGod Posted January 4, 2021 Author Share Posted January 4, 2021 (edited) @Locked Down Are you using the Intel internal card or did you swap it out? if your using the Intel drivers then are they not driving you abit mad? I got them working as best as they can do on a few different boards now and it works but it’s covered with issues, I tried to put up with it and all its silly quirks but in the end I gave up on it for now. Too slow, very unforgiving if your flicking around from OS to OS and not everything that should work via Bluetooth does work. My wireless MX Master 2 mouse will not connect via it no mater what I do or try including clean boots and different systems. Oh and I can’t stand the fact the kext package is so huge in size...what the hell is that all about? P.s I hope you had a good xmas and new year Edited January 4, 2021 by AudioGod Link to comment Share on other sites More sharing options...
Locked Down Posted January 4, 2021 Share Posted January 4, 2021 1 minute ago, AudioGod said: @Locked Down Are you using the Intel internal card or did you swap it out? if your using the Intel drivers then are they not driving you abit mad? I got them working as best as they can do on a few different boards now and it works but it’s covered with issues, I tried to put up with it and all its like silly quirks but in the end I gave up on it for now. Too slow, very unforgiving if your flicking around from OS to OS and not everything that should work via Bluetooth does work. My wireless MX Master 2 wires less mouse will not connect via it no mater what I do or try including clean boots and different systems. Oh and I can’t stand the fact the kext package is so huge in size...what the hell is that all about? P.s I hope you had a good x,as and new year I have wired lan for internet etc and just use the bluetooth and wifi combo for unlocking with Apple Watch. Just for that it isn't really necessary to purchase another card. They may be cheapish but no point really in my case and I use wired mouse and keyboard. 1 Link to comment Share on other sites More sharing options...
AudioGod Posted January 4, 2021 Author Share Posted January 4, 2021 1 minute ago, Locked Down said: I have wired lan for internet etc and just use the bluetooth and wifi combo for unlocking with Apple Watch. Just for that it isn't really necessary to purchase another card. They may be cheapish but no point really in my case and I use wired mouse and keyboard. Yeah that was my theory too but my wireless mouse refusing to connect to it was the point where I got frustrated and gave up...lol im wired too but have a lot of Bluetooth devices. It’s a shame really cos I would prefer to use it then not. oh well. In fairness the drivers have come along way compared to how they used to be, maybe one day they will nail it. (Fingers crossed) 1 Link to comment Share on other sites More sharing options...
AudioGod Posted January 4, 2021 Author Share Posted January 4, 2021 (edited) OpenCore 0.6.5 EFI Update (Big Sur Ready), 4th January 2021 (Use With Bios Revision F11L or Newer) The EFIs and DSDTs have now been updated to the my latest versions. Changes made include, AppleALC 1.5.6, WhateverGreen 1.4.6, IntelMausi 1.0.5, OpenCore Updated to Revision 0.6.5 (Big Sur 11.1 Ready), OpenCanopy is Enabled as Standard, New OpenCanopy Icons Plus other minor tweaks and changes to all of the configs. OpenCore EFI Update v0.6.5 - 04/01/2021 OC 065 19,1 Z390 Master EFI 040121.zip - OpenCore v0.6.5, SMBios iMac19,1 OC 065 020121 1,1 Z390 Master 040121.zip - OpenCore v0.6.5, SMBios iMacPro1,1 (IGPU Disabled) PLEASE DON’T FORGET TO RESET YOUR NVRAM BEFORE BOOTING INTO THE NEW EFI FOR THE FIRST TIME, Note - If your not using a 5700 XT or any other Navi GPU then remove agdpmod=pikera from the boot arguments. Note 2 - Do not try to carry across your old OpenCore Config.plist to the new EFI as to many changes have occurred in 0.6.0. Use the new Config.plist instead. For OpenCore Using PlistEdit Pro add your details by modifying the following PLEASE NOTE - These EFIs are setup to be used with your msr Unlocked so make sure you use the correct bios settings listed below or use the F11L Unlocked Profile I have provided. Additional Downloads Z390AORUSMASTER.F11l.zip - Aorus Z390 Master Bios Firmware F11L PlistEdit Pro.zip - PlistEdit Pro (use to edit OpenCore) PLEASE NOTE - MSR Unlock is now baked into the BIOS as a setting so you no longer need my bios profile to unlock your MSR. BIOS SETTINGS (Bios Revision F11L) • Enter BIOS -> Press Delete -> Enter Setup • Save & Exit -> Load Optimized Defaults • Boot -> CFG Lock -> Disabled • Boot -> Windows 8/10 Features -> Win 8/10 WHQL • Boot -> CSM Support -> Disabled (Can be set to Enabled if need be but try to have it set to Disabled first) • Favourites -> Extreme Memory Profile (X.M.P.) -> Profile1 • Favourites -> VT-d -> Disabled (Can be set to Enabled or Disabled, Your choice) • Settings -> IO Ports -> Internal Display Output -> PCIe 1 Slot • Settings -> IO Ports -> Internal Graphics -> Enabled (Disabled If Using SMBios 1,1) • Settings -> IO Ports -> DVMT Pre-Allocated -> 64M • Settings -> IO Ports -> DVMT Total GFX0-Allocated -> 256M • Settings -> IO Ports -> Aperture Size -> 256MB• Settings -> IO Ports -> Wifi -> Disabled • Settings -> IO Ports -> Audio Controller -> Enabled • Settings -> IO Ports -> Above 4G Decoding -> Enabled • Settings -> IO Ports -> Super IO Configuration -> Serial Port -> Disabled • Settings -> IO Ports -> USB Configuration -> Legacy USB Support -> Auto • Settings -> IO Ports -> USB Configuration -> XHCI Hands-off -> Enabled • Settings -> Miscellaneous -> Software Guard Extensions (SGX) -> Disabled • Settings -> Platform Power -> Platform Power Management -> Enabled • Settings -> Platform Power -> ErP -> Enabled • Settings -> Platform Power -> RC6(Render Standby) -> Enabled • Save & Exit → Save & Exit Setup F11L BIOS Profile With MSR Unlocked & All The Correct Settings Dialled in for you - The Easy Way I have made this bios profile for you all to use that will unlock CFG on your motherboard making it play alot more friendly with the NVRam. It also has all the bios settings listed on this guide pre done and saved onto the profile. Default F11L.zip - Use with Bios Revision F11L ONLY 1 - Download the profile and save it to a USB Key 2 - Go into the bios, 3 - Load the profile, 4 - Save and exit 5 - Go straight back into the bios and save your bios to a new profile and name it Default CFG Unlocked or something like that. 6 - Save the changes and then restart and your done, your motherboard will now be CFG (MSR) Unlocked and all the correct settings will be dialled in for you. Edited January 4, 2021 by AudioGod 2 4 Link to comment Share on other sites More sharing options...
luckas Posted January 10, 2021 Share Posted January 10, 2021 Thank you very much! 1 Link to comment Share on other sites More sharing options...
luckas Posted January 11, 2021 Share Posted January 11, 2021 My Mac finally works sleep option with Bluetooth card and this adapter. Connecting to internal USB doesn't work. 1 Link to comment Share on other sites More sharing options...
Benjamin Franklin Posted January 13, 2021 Share Posted January 13, 2021 Anyone else experiencing random Safari crashes since the latest update? Link to comment Share on other sites More sharing options...
AudioGod Posted January 13, 2021 Author Share Posted January 13, 2021 (edited) 1 hour ago, Benjamin Franklin said: Anyone else experiencing random Safari crashes since the latest update? Not over here but If your using 19.1 then you might want to set `SecureBootModel` to `Disabled` Edited January 13, 2021 by AudioGod Link to comment Share on other sites More sharing options...
Benjamin Franklin Posted January 13, 2021 Share Posted January 13, 2021 12 minutes ago, AudioGod said: Not over here but If your using 19.1 then you might want to set `SecureBootModel` to `Disabled` I am using 19,1. I have a i59600K with a RX570, do you recommend switching to 1,1? Link to comment Share on other sites More sharing options...
AudioGod Posted January 13, 2021 Author Share Posted January 13, 2021 1 hour ago, Benjamin Franklin said: I am using 19,1. I have a i59600K with a RX570, do you recommend switching to 1,1? No not really buddy, just try doing the above and see if it helps you? ive not had any reports of safari crashing though. Link to comment Share on other sites More sharing options...
Locked Down Posted February 2, 2021 Share Posted February 2, 2021 (edited) New version of Opencore, 0.6.6, has been released with new VirtualSMC, Lilu, Whatevergreen & AppleALC. Quite big major changes in this one, so be sure to check the documentation before attempting to upgrade this time. Edited February 2, 2021 by Locked Down Link to comment Share on other sites More sharing options...
AudioGod Posted February 3, 2021 Author Share Posted February 3, 2021 (edited) SUPRISE!!!! As Release 0.6.6 has made so many changes in this revision I thought I would post an updated EFI for you all so here it is. OpenCore 0.6.6 EFI Update (Big Sur 11.2 Ready), 3rd February 2021 (Use With Bios Revision F11L or Newer) The EFIs and DSDTs have now been updated to the my latest versions. Changes made include, Lilu 1.5.1 AppleALC 1.5.7, WhateverGreen 1.4.7, VirtualSMC 1.2.0 OpenCore Updated to Revision 0.6.6 (Big Sur 11.2 Ready), New OpenCanopy Icons OpenCanopy is Enabled as Standard, New OpenCanopy Icons Plus other minor tweaks and changes to all of the configs. OpenCore EFI Update v0.6.6 - 03/02/2021 OC 066 1,1 Z390 Master EFI 020221 .zip - OpenCore v0.6.6, SMBios iMacPro1,1 (IGPU Disabled) OC 066 19,1 Z390 Master EFI 020221.zip - OpenCore v0.6.6, SMBios iMac19,1 IMPORTANT - OPENCORE HAS CHANGED THE WAY THE BOOTSTRAP WORKS SO YOU WILL NEED TO RESELECT YOUR BIG SUR DISK (F12 DISK SELECT OR FROM WITHIN THE BIOS) AND THEN RESET YOUR NVRAM BEFORE BOOTING INTO THE NEW EFI FOR THE FIRST TIME, THIS IS VITAL. Note - If your not using a 5700 XT or any other Navi GPU then remove agdpmod=pikera from the boot arguments. Note 2 - Do not try to carry across your old OpenCore Config.plist to the new EFI as to many changes have occurred in 0.6.0. Use the new Config.plist instead. For OpenCore Using PlistEdit Pro add your details by modifying the following PLEASE NOTE - These EFIs are setup to be used with your msr Unlocked so make sure you use the correct bios settings listed below or use the F11L Unlocked Profile I have provided. Additional Downloads Z390AORUSMASTER.F11l.zip - Aorus Z390 Master Bios Firmware F11L PlistEdit Pro.zip - PlistEdit Pro (use to edit OpenCore) PLEASE NOTE - MSR Unlock is now baked into the BIOS as a setting so you no longer need my bios profile to unlock your MSR. BIOS SETTINGS (Bios Revision F11L) • Enter BIOS -> Press Delete -> Enter Setup • Save & Exit -> Load Optimized Defaults • Boot -> CFG Lock -> Disabled • Boot -> Windows 8/10 Features -> Win 8/10 WHQL • Boot -> CSM Support -> Disabled (Can be set to Enabled if need be but try to have it set to Disabled first) • Favourites -> Extreme Memory Profile (X.M.P.) -> Profile1 • Favourites -> VT-d -> Disabled (Can be set to Enabled or Disabled, Your choice) • Settings -> IO Ports -> Internal Display Output -> PCIe 1 Slot • Settings -> IO Ports -> Internal Graphics -> Enabled (Disabled If Using SMBios 1,1) • Settings -> IO Ports -> DVMT Pre-Allocated -> 64M • Settings -> IO Ports -> DVMT Total GFX0-Allocated -> 256M • Settings -> IO Ports -> Aperture Size -> 256MB• Settings -> IO Ports -> Wifi -> Disabled • Settings -> IO Ports -> Audio Controller -> Enabled • Settings -> IO Ports -> Above 4G Decoding -> Enabled • Settings -> IO Ports -> Super IO Configuration -> Serial Port -> Disabled • Settings -> IO Ports -> USB Configuration -> Legacy USB Support -> Auto • Settings -> IO Ports -> USB Configuration -> XHCI Hands-off -> Enabled • Settings -> Miscellaneous -> Software Guard Extensions (SGX) -> Disabled • Settings -> Platform Power -> Platform Power Management -> Enabled • Settings -> Platform Power -> ErP -> Enabled • Settings -> Platform Power -> RC6(Render Standby) -> Enabled • Save & Exit → Save & Exit Setup F11L BIOS Profile With MSR Unlocked & All The Correct Settings Dialled in for you - The Easy Way I have made this bios profile for you all to use that will unlock CFG on your motherboard making it play alot more friendly with the NVRam. It also has all the bios settings listed on this guide pre done and saved onto the profile. Default F11L.zip - Use with Bios Revision F11L ONLY 1 - Download the profile and save it to a USB Key 2 - Go into the bios, 3 - Load the profile, 4 - Save and exit 5 - Go straight back into the bios and save your bios to a new profile and name it Default CFG Unlocked or something like that. 6 - Save the changes and then restart and your done, your motherboard will now be CFG (MSR) Unlocked and all the correct settings will be dialled in for you. Edited February 3, 2021 by AudioGod 2 4 Link to comment Share on other sites More sharing options...
eSaF Posted February 3, 2021 Share Posted February 3, 2021 1 hour ago, AudioGod said: SUPRISE!!!! As Release 0.6.6 has made so many changes in this revision I thought I would post an updated EFI for you all so here it is. OpenCore 0.6.6 EFI Update (Big Sur 11.2 Ready), 3rd February 2021 (Use With Bios Revision F11L or Newer) The EFIs and DSDTs have now been updated to the my latest versions. Changes made include, Lilu 1.5.1 AppleALC 1.5.7, WhateverGreen 1.4.7, VirtualSMC 1.2.0 OpenCore Updated to Revision 0.6.6 (Big Sur 11.2 Ready), New OpenCanopy Icons OpenCanopy is Enabled as Standard, New OpenCanopy Icons Plus other minor tweaks and changes to all of the configs. OpenCore EFI Update v0.6.6 - 03/02/2021 OC 066 1,1 Z390 Master EFI 020221 .zip 3.92 MB · 4 downloads - OpenCore v0.6.6, SMBios iMacPro1,1 (IGPU Disabled) OC 066 19,1 Z390 Master EFI 020221.zip 3.93 MB · 6 downloads - OpenCore v0.6.6, SMBios iMac19,1 IMPORTANT - OPENCORE HAS CHANGED THE WAY THE BOOTSTRAP WORKS SO YOU WILL NEED TO RESELECT YOUR BIG SUR DISK (F12 DISK SELECT OR FROM WITHIN THE BIOS) AND THEN RESET YOUR NVRAM BEFORE BOOTING INTO THE NEW EFI FOR THE FIRST TIME, THIS IS VITAL. Note - If your not using a 5700 XT or any other Navi GPU then remove agdpmod=pikera from the boot arguments. Note 2 - Do not try to carry across your old OpenCore Config.plist to the new EFI as to many changes have occurred in 0.6.0. Use the new Config.plist instead. For OpenCore Using PlistEdit Pro add your details by modifying the following PLEASE NOTE - These EFIs are setup to be used with your msr Unlocked so make sure you use the correct bios settings listed below or use the F11L Unlocked Profile I have provided. Additional Downloads Z390AORUSMASTER.F11l.zip - Aorus Z390 Master Bios Firmware F11L PlistEdit Pro.zip - PlistEdit Pro (use to edit OpenCore) PLEASE NOTE - MSR Unlock is now baked into the BIOS as a setting so you no longer need my bios profile to unlock your MSR. BIOS SETTINGS (Bios Revision F11L) • Enter BIOS -> Press Delete -> Enter Setup • Save & Exit -> Load Optimized Defaults • Boot -> CFG Lock -> Disabled • Boot -> Windows 8/10 Features -> Win 8/10 WHQL • Boot -> CSM Support -> Disabled (Can be set to Enabled if need be but try to have it set to Disabled first) • Favourites -> Extreme Memory Profile (X.M.P.) -> Profile1 • Favourites -> VT-d -> Disabled (Can be set to Enabled or Disabled, Your choice) • Settings -> IO Ports -> Internal Display Output -> PCIe 1 Slot • Settings -> IO Ports -> Internal Graphics -> Enabled (Disabled If Using SMBios 1,1) • Settings -> IO Ports -> DVMT Pre-Allocated -> 64M • Settings -> IO Ports -> DVMT Total GFX0-Allocated -> 256M • Settings -> IO Ports -> Aperture Size -> 256MB• Settings -> IO Ports -> Wifi -> Disabled • Settings -> IO Ports -> Audio Controller -> Enabled • Settings -> IO Ports -> Above 4G Decoding -> Enabled • Settings -> IO Ports -> Super IO Configuration -> Serial Port -> Disabled • Settings -> IO Ports -> USB Configuration -> Legacy USB Support -> Auto • Settings -> IO Ports -> USB Configuration -> XHCI Hands-off -> Enabled • Settings -> Miscellaneous -> Software Guard Extensions (SGX) -> Disabled • Settings -> Platform Power -> Platform Power Management -> Enabled • Settings -> Platform Power -> ErP -> Enabled • Settings -> Platform Power -> RC6(Render Standby) -> Enabled • Save & Exit → Save & Exit Setup F11L BIOS Profile With MSR Unlocked & All The Correct Settings Dialled in for you - The Easy Way I have made this bios profile for you all to use that will unlock CFG on your motherboard making it play alot more friendly with the NVRam. It also has all the bios settings listed on this guide pre done and saved onto the profile. Default F11L.zip - Use with Bios Revision F11L ONLY 1 - Download the profile and save it to a USB Key 2 - Go into the bios, 3 - Load the profile, 4 - Save and exit 5 - Go straight back into the bios and save your bios to a new profile and name it Default CFG Unlocked or something like that. 6 - Save the changes and then restart and your done, your motherboard will now be CFG (MSR) Unlocked and all the correct settings will be dialled in for you. Spoiler Nice one B - You just couldn't walk away could yah bro? 1 1 Link to comment Share on other sites More sharing options...
AudioGod Posted February 3, 2021 Author Share Posted February 3, 2021 14 minutes ago, eSaF said: Reveal hidden contents Nice one B - You just couldn't walk away could yah bro? I felt bad to leave it on 0.6.5 when 0.6.6 was such a major update. There will come a time where OC becomes to different for me to safely continue rolling out the EFIs for the pro and master without a ton of testing. I do what I can when I can. LOCKDOWN BOREDOM! 2 Link to comment Share on other sites More sharing options...
eSaF Posted February 3, 2021 Share Posted February 3, 2021 7 minutes ago, AudioGod said: LOCKDOWN BOREDOM! Hey B that's my excuse!!!! - Nice one though Bro, they will be a lot of happy campers that you came through once again. Link to comment Share on other sites More sharing options...
Benjamin Franklin Posted February 4, 2021 Share Posted February 4, 2021 17 hours ago, eSaF said: Hey B that's my excuse!!!! - Nice one though Bro, they will be a lot of happy campers that you came through once again. Couldn't have said it better! Thanks B!! 2 Link to comment Share on other sites More sharing options...
dredhorse Posted February 9, 2021 Share Posted February 9, 2021 Hi, would it be hard to switch from the Aorus Z390 Master to a "lower" version of the MB? I still have the Bios issues, and I don't know if it is the Motherboard or the CPU. I asked Gigabyte for a replacement but I don't know if I will get one, plus it looks like the z390 master is not available anymore. As I highly appreciate the work Audiogod is doing I would like to stick with the same hardware, especially as MacOS and Windows is running totally fine with the hardware. Link to comment Share on other sites More sharing options...
seha39 Posted February 12, 2021 Share Posted February 12, 2021 Merhaba."OpenCore macOS Catalina 10.15.5 AMD & Intel İmajı"Claus'un linkteki imajını indirip, USB'ye yazdırdıktan sonra EFI klasörümü sistemime uygun olan ile değiştirdim. BIOS ayarlarımı da yerine getirdim fakat USB'den Boot edip kurulum aşamasına geçemedim. Nerede neyi hatalı yapıyorum?Desktop'a kurulum yapmaya çalışıyorum.Intel Core i5-9600KIntel(r) HD Graphics 630.Sapphire Pulse RX570 8 GB.High Definition Audio Controller.Intel(r) Dual band Wireless- AC 9560.PCI-e gigabit Ethernet Controller ı217.DDR4/8GB/ 3200 MT/s Just now, seha39 said: Merhaba."OpenCore macOS Catalina 10.15.5 AMD & Intel İmajı"Claus'un linkteki imajını indirip, USB'ye yazdırdıktan sonra EFI klasörümü sistemime uygun olan ile değiştirdim. BIOS ayarlarımı da yerine getirdim fakat USB'den Boot edip kurulum aşamasına geçemedim. Nerede neyi hatalı yapıyorum?Desktop'a kurulum yapmaya çalışıyorum.Intel Core i5-9600KIntel(r) HD Graphics 630.Sapphire Pulse RX570 8 GB.High Definition Audio Controller.Intel(r) Dual band Wireless- AC 9560.PCI-e gigabit Ethernet Controller ı217.DDR4/8GB/ 3200 MT/s Denedim sonuç aynı daha önceleri sorunsuz yükleme yapabiliyordum sonra diskleri silmiştim windowsa geçtim ve BIOS güncellemeden sonra bu sorunla karşılaştım. Tekrar yukleme ekranina dusuyor. Kurulum ekranına kadar sistem Boot ediyor fakat diski seçip yüklemeye geldiğim zaman olmuyor diskte sanki bir bloke varmış gibi yükleme yapmıyor. Dosya Ekleri 20210210_175607.jpg 85,2 KB · Görüntüleme: 4 20210210_175614.jpg 78,4 KB · Görüntüleme: 4 20210210_175621.jpg 92,3 KB · Görüntüleme: 4 20210210_175629.jpg 101,7 KB · Görüntüleme: 4 20210210_175637.jpg 89,3 KB · Görüntüleme: 4 20210210_175644.jpg 82,9 KB · Görüntüleme: 4 Link to comment Share on other sites More sharing options...
Locked Down Posted February 12, 2021 Share Posted February 12, 2021 5 minutes ago, seha39 said: Merhaba.Claus'un linkteki imajını indirip, USB'ye yazdırdıktan sonra EFI klasörümü sistemime uygun olan ile değiştirdim. BIOS ayarlarımı da yerine getirdim fakat USB'den Boot edip kurulum aşamasına geçemedim. Nerede neyi hatalı yapıyorum? Buraya İngilizce yazmanız gerekiyor. Link to comment Share on other sites More sharing options...
seha39 Posted February 12, 2021 Share Posted February 12, 2021 50 minutes ago, Locked Down said: Buraya İngilizce yazmanız gerekiyor. Hi. After downloading the image of Claus on the link and burning it to USB, I replaced my EFI folder with the appropriate one for my system. I did my BIOS settings as well, but I could not boot from USB and proceed to the setup phase. Where am I doing wrong? Link to comment Share on other sites More sharing options...
Locked Down Posted February 13, 2021 Share Posted February 13, 2021 @seha39, don't use somebody else's image, you don't know what it really is. Download macOS from Apple yourself and use that, you then know that has not been interfered with. If you don't have a Mac to download it use gibMacos. How did you create the installer on the USB stick? Is your EFI folder in the EFI partition on your USB stick? It has to be in the correct place. Have you pressed F12 at boot up and booted from the USB stick? 2 Link to comment Share on other sites More sharing options...
Recommended Posts