Jump to content

[pre-release] macOS High Sierra


3,737 posts in this topic

Recommended Posts

@gengik84

After a BIOS reset and a creating a new installer with a fresh clover r4187 with clean config and kexts, I managed to install macOS High Sierra DP 7 on Asus Prime Z270-A successfully with an AMD RX 560 4GB :)

the SATA ports work OOB without the need of SATA-200-series-unsupported.kext ;)

Addition:

Thanks for your help as always :)

 

Great job  :) Can I have Bios settings in MP, please? I intend to buy the same motherboard. Thanks

  • Like 1
Link to comment
Share on other sites

I'm getting a strange issue after a fresh install (db7) (apfs).

fs_get_inode_with_hint:8012: failed to load inode 547037 ret 22

fs_get_inode_with_hint:8012: failed to load inode 547037 ret 22

Error loading kernel cache (0xe)

Boot failed, sleeping for 10 seconds before exiting...

Laptop in my sig.

Wiped HDD with Yosemite, created partitions, reboot into High Sierra installer. Format High Sierra partition as APFS. Install without issue but upon trying to boot into the actual os I get the error above.

 

O/T Sierra 10.12.6 installs fine but always creates coreStorage that I have to revert.

 

Samsung 850 EVO 500g SSD. Latest firmware installed.

 

Sent from my SM-G930F using Tapatalk

Link to comment
Share on other sites

Great job  :) Can I have Bios settings in MP, please? I intend to buy the same motherboard. Thanks

Here it is.

I just removed serial number/MLB and themes

 

Specs:

The system has a Core i7 7700 3.6 GHz with the stock cooler

16 GB of Geil EVO X RGB 3000 MHz

250 GB Samsung EVO 850 GB SSD

1 TB Western Digital Blue 7200 RPM

Asus Srtix RX 560 GPU

CoolerMaster G650 PSU

Asus Prime Z270-A Clover r4187 with BIOS Images.zip

Link to comment
Share on other sites

I ,my download applestore with p.b.utility again 10.13.6

how to receive  7 ?

 

from apple update I have 7 but after download and reboot no install ,any help

 

by

The 13.0.41 is the version of the Installer app not the version or the build number of the macOS, check the version of macOS by using the "Get Info" if the version is 13.0.57 then it is the DP 7 otherwise you need to remove the installer and download it again.

post-1011040-0-18464200-1503566400_thumb.png

  • Like 1
Link to comment
Share on other sites

The 13.0.41 is the version of the Installer app not the version or the build number of the macOS, check the version of macOS by using the "Get Info" if the version is 13.0.57 then it is the DP 7 otherwise you need to remove the installer and download it again.

thank you,is 7

on both cases I have a error install. wait GM or stay on 4

exasperated

Link to comment
Share on other sites

Can you post your Clover boot.log so I can see if you implemented the changes correctly?  Also, you have several Clover DSDT patches even though you use a custom DSDT.  I didn't know why you used them so I didn't try to change them.  You might try to remove as much from your config.plist as possible and see if you can get your video to load.  The less you have, the easier it is to isolate the problem.

Post the boot log in clover with your dsdt and config.list.  Thanks for trying to help me.

preboot.log.zip

Link to comment
Share on other sites

Last night I can easily reach the installer screen but now same USB I always getting OSInstall.mpkg error? What am I doing wrong?

You either use an old SMBIOS settings, or you have EmuVaraiableUEFI.efi and if you have windows installed on another or the same hard disk you'll get the OSInstall.mpkg error.

SO update your SMBIOS info, remove EmuVaraiableUEFI.efi from the /EFI/Clover/driversUEFI64 and the nvram.plist from the EFI root on your bootable device (USB) and unplug windows disk if you have any.

  • Like 1
Link to comment
Share on other sites

Post the boot log in clover with your dsdt and config.list.  Thanks for trying to help me.

 

Try reinstalling Clover without selecting CsmVideoDxe-64.  I made further modifications to your config.plist.  You may lose some functionality with my deletions (or even get a KP).  However, our goal is to rule out anything that might be preventing video from loading so we need to delete all non-essential settings.  We can try putting them back after you get video to load with DP6.

 

config.plist.zip

  • Like 1
Link to comment
Share on other sites

Is it normal for GPU to drop to x8 PCIe width after installing an NVMe M.2 x4 drive in High Sierra?

 

Seems like there should be more than enough PCIe lanes on a Z270 board to accommodate the full x16 slot width.

Link to comment
Share on other sites

Is it normal for GPU to drop to x8 PCIe width after installing an NVMe M.2 x4 drive in High Sierra?

 

Seems like there should be more than enough PCIe lanes on a Z270 board to accommodate the full x16 slot width.

Depends on the board, most will drop to x8 when using the second x16 or x4 PCIe slot.

Link to comment
Share on other sites

Try reinstalling Clover without selecting CsmVideoDxe-64.  I made further modifications to your config.plist.  You may lose some functionality with my deletions (or even get a KP).  However, our goal is to rule out anything that might be preventing video from loading so we need to delete all non-essential settings.  We can try putting them back after you get video to load with DP6.

Thanks, I'll try a bit later (now I am at work) the result will be misleading.

 

 

 

Link to comment
Share on other sites

Hi

if i'm installing DP7 to a new pc with usb created by createinstallmedia

how do I choose between HFS+ and APFS?

it's converting to APFS automatically :(

 

Before stage 2 start to install, try to edit true to be false. It may works fine.

 

/macOS Install Data/minstallconfig.xml

    <key>ConvertToAPFS</key>

    <false/>

  • Like 3
Link to comment
Share on other sites

 

Thanks, I'll try a bit later (now I am at work) the result will be misleading.

 

 

 

 

Try reinstalling Clover without selecting CsmVideoDxe-64.  I made further modifications to your config.plist.  You may lose some functionality with my deletions (or even get a KP).  However, our goal is to rule out anything that might be preventing video from loading so we need to delete all non-essential settings.  We can try putting them back after you get video to load with DP6.

 

attachicon.gifconfig.plist.zip

I tried Your suggested option in kext only FakeSMC.kext и VoodooPS2Controller.kext , but the error is similar as before, log and photo attached.

post-1538813-0-78468300-1503649371_thumb.jpg

preboot.zip

Link to comment
Share on other sites

i checked all parts of macpro5,1 firmware to search ff/ffm information. strange. also shown other pattern compared to other firmware as what i known

macpro5,1 can't see correct ff/ffm infomation.

 

if you can test, try this

MP51.88Z.0084.B00.1708080528 and not use ff/ffm at config with clover r4184.

 

thanks

I've tried this version MP51.88Z.0084.B00.1708080528 with R4187, but manually wrote FF 0xE80FE136 && FFM 0xFF1FFF3F w\o PF key (Valid 0xFFFF) and from the Log:

3:511  0:011  Using ProductName from config
3:511  0:000  ProductName: MacPro5,1
3:511  0:000  Using latest BiosVersion from config
3:511  0:000  BiosVersion: MP51.88Z.0084.B00.1708080528
3:511  0:000  BiosReleaseDate: 08/08/17
3:511  0:000  Found same FirmwareFeatures in clover and config
3:511  0:000  FirmwareFeatures: 0xE80FE136
3:511  0:000  Found same FirmwareFeaturesMask in clover and config
3:511  0:000  FirmwareFeaturesMask: 0xFF1FFF3F
3:511  0:000  Using PlatformFeature from clover
3:511  0:000  PlatformFeature: 0xFFFF

One main thing. My board has 4 SATA controllers: ICH10R, 2x JMicron(s) and Marvell (see my signature). Earlier I had problems with connected HDDs to first 0,1,2 ports of ICH10 and both JM, but no problem with Marvell. Though yesterday I booted only with Marvell and absolutely w\o any problem updated system to Dev7 from AppStore. Yep.

post-609887-0-09024900-1503657729_thumb.png

  • Like 2
Link to comment
Share on other sites

Last night I can easily reach the installer screen but now same USB I always getting OSInstall.mpkg error? What am I doing wrong?

Upload your clover log

 

나의 LG-F800S 의 Tapatalk에서 보냄

I've tried this version MP51.88Z.0084.B00.1708080528 with R4187, but manually wrote FF 0xE80FE136 && FFM 0xFF1FFF3F w\o PF key (Valid 0xFFFF) and from the Log:

3:511  0:011  Using ProductName from config
3:511  0:000  ProductName: MacPro5,1
3:511  0:000  Using latest BiosVersion from config
3:511  0:000  BiosVersion: MP51.88Z.0084.B00.1708080528
3:511  0:000  BiosReleaseDate: 08/08/17
3:511  0:000  Found same FirmwareFeatures in clover and config
3:511  0:000  FirmwareFeatures: 0xE80FE136
3:511  0:000  Found same FirmwareFeaturesMask in clover and config
3:511  0:000  FirmwareFeaturesMask: 0xFF1FFF3F
3:511  0:000  Using PlatformFeature from clover
3:511  0:000  PlatformFeature: 0xFFFF
One main thing. My board has 4 SATA controllers: ICH10R, 2x JMicron(s) and Marvell (see my signature). Earlier I had problems with connected HDDs to first 0,1,2 ports of ICH10 and both JM, but no problem with Marvell. Though yesterday I booted only with Marvell and absolutely w\o any problem updated system to Dev7 from AppStore. Yep.
Thank you for report.

MacPro5,1 was checked by you.

 

Soon i will update biosversion for macpro5,1 with other patch

 

나의 LG-F800S 의 Tapatalk에서 보냄

  • Like 1
Link to comment
Share on other sites

I tried Your suggested option in kext only FakeSMC.kext и VoodooPS2Controller.kext , but the error is similar as before, log and photo attached.

 

If you look at your own preboot.log, you can see that you didn't disable CsmVideoDxe-64.  

0:270  0:001  Loading CsmVideoDxe-64.efi  status=Success 

You also have kexts in your Other folder that are loading when you said you just used FakeSMC and VoodooPS2Controller.  

33:607  0:012  Preparing kexts injection for arch=x86_64 from EFI\CLOVER\kexts\Other
33:607  0:000    Extra kext: EFI\CLOVER\kexts\Other\ACPIBatteryManager.kext
33:660  0:053    Extra kext: EFI\CLOVER\kexts\Other\Lilu.kext
33:677  0:016    Extra kext: EFI\CLOVER\kexts\Other\IntelGraphicsFixup.kext
33:688  0:011    Extra kext: EFI\CLOVER\kexts\Other\AppleBusPowerControllerEC0.kext
33:706  0:017    Extra kext: EFI\CLOVER\kexts\Other\FakeSMC.kext
33:725  0:019    Extra kext: EFI\CLOVER\kexts\Other\AsusNBFnKeys.kext
33:738  0:013    Extra kext: EFI\CLOVER\kexts\Other\VoodooI2C.kext
33:766  0:028    Extra kext: EFI\CLOVER\kexts\Other\RealtekRTL8111.kext
33:781  0:015    Extra kext: EFI\CLOVER\kexts\Other\VoodooPS2Controller.kext
33:787  0:005      Extra PlugIn kext: EFI\CLOVER\kexts\Other\VoodooPS2Controller.kext\Contents\PlugIns\VoodooPS2Keyboard.kext
33:827  0:039      Extra PlugIn kext: EFI\CLOVER\kexts\Other\VoodooPS2Controller.kext\Contents\PlugIns\VoodooPS2Mouse.kext
33:856  0:029      Extra PlugIn kext: EFI\CLOVER\kexts\Other\VoodooPS2Controller.kext\Contents\PlugIns\VoodooPS2Trackpad.kext
33:902  0:045    Extra kext: EFI\CLOVER\kexts\Other\VoodooHDA.kext

Keep working at this.  It look me 6 days to figure out what I needed to do and to actually do it.  If it helps, compare your preboot.log with mine.

 

mnfesq.bootlog.log.txt

 

Mine's pretty messy. You can see that I start using one config.plist (which I use for Sierra) and switched to a different config.plist to boot to High Sierra.  You can also see that I have multiple DSDT files and use DSDT.aml to boot to Sierra and DSDT1.aml to boot to High Sierra.  I have to have separate DSDT files because, when I disable my Radeon GPU in my DSDT, I get a KP in Sierra but HAVE TO disable my Radeon GPU in order to get High Sierra to boot.

Link to comment
Share on other sites

If you look at your own preboot.log, you can see that you didn't disable CsmVideoDxe-64.  

0:270  0:001  Loading CsmVideoDxe-64.efi  status=Success 

You also have kexts in your Other folder that are loading when you said you just used FakeSMC and VoodooPS2Controller.  


Maybe you were watching another file download but my latest version does not.

 

0:128  0:000  === [ LoadDrivers ] =======================================
0:131  0:003  Loading AppleImageCodec-64.efi  status=Success
0:138  0:006  Loading AppleKeyAggregator-64.efi  status=Success
0:144  0:006  Loading AppleUITheme-64.efi  status=Success
0:149  0:004  Loading DataHubDxe-64.efi  status=Success
0:157  0:007  Loading FirmwareVolume-64.efi  status=Success
0:163  0:006  Loading FSInject-64.efi  status=Success
0:168  0:005  Loading OsxAptioFixDrv-64.efi  status=Success
0:170  0:001  Loading OsxFatBinaryDrv-64.efi  status=Success
0:175  0:004  Loading HFSPlus64.efi  status=Success
0:179  0:003   - driver needs connecting
0:179  0:000  Loading PartitionDxe-64.efi  status=Success
0:182  0:003   - driver needs connecting
0:182  0:000  Loading SMCHelper-64.efi  status=Success
0:187  0:004  Loading VBoxHfs-64.efi  status=Success
0:189  0:002   - driver needs connecting

 

 
и далее
 

18:338  0:014  Preparing kexts injection for arch=x86_64 from EFI\CLOVER\kexts\Other

18:341  0:002    Extra kext: EFI\CLOVER\kexts\Other\FakeSMC.kext
18:353  0:011    Extra kext: EFI\CLOVER\kexts\Other\VoodooPS2Controller.kext
18:357  0:004      Extra PlugIn kext: EFI\CLOVER\kexts\Other\VoodooPS2Controller.kext\Contents\PlugIns\VoodooPS2Keyboard.kext
18:369  0:012      Extra PlugIn kext: EFI\CLOVER\kexts\Other\VoodooPS2Controller.kext\Contents\PlugIns\VoodooPS2Mouse.kext
18:374  0:004      Extra PlugIn kext: EFI\CLOVER\kexts\Other\VoodooPS2Controller.kext\Contents\PlugIns\VoodooPS2Trackpad.kext

preboot.zip

  • Like 1
Link to comment
Share on other sites

I always have a USB OS X  to use in emergency !

I loaded High Sierra USB . ran the High Sierra app on USB!

High Sierra installed to the USB !

From the install folder it made I ran the mkginstaller from package folder.

It updated Sierra ! Boots and runs but lots of problems with Finder. 

will not except my ID password.

When I get OS X running well on USB !! I restore to HD.

 Now I only have Sierra working Great on My Dell 960 desktop with Clover.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...