MaLd0n Posted August 23, 2018 Author Share Posted August 23, 2018 59 minutes ago, giacomoleopardo said: Yes. New dump attached. Send me iMac.zip DSDT.aml.zip Link to comment Share on other sites More sharing options...
P1aton0FF Posted August 23, 2018 Share Posted August 23, 2018 17 hours ago, MaLd0n said: check if video work CLOVER.zip Nope. I get "no signal" if platform-id 59120000 fake id 59128086 With fakeid 1912 and 3E92 and any platform-id - is loaded, but "Graphics driver failed to load: could not register with framebuffer driver". Have a panic if platform-id 59120003. Platform Platform-ID 3e920003 Fake ID empty - loading, but "Graphics driver failed to load: could not register with framebuffer driver". I tried 18.1, 18.2, 18.3... Tried BBCoffee630.kext, AppleIntelKBLGraphicsFramebufferInjector_3e9x.kext - without results. Send me Aleksandrs-iMac.zip Link to comment Share on other sites More sharing options...
josephien Posted August 23, 2018 Share Posted August 23, 2018 (edited) @ Madlon here is the runme zip file, can you verify the dsdt and patch it for me? I'm running 10,13,6 on msi z170a gaming m7 with an i5 7600k on stock (planning overclock later) there's one 16gb memory stick and booting of an ssd Send me Marcs-iMac.fritz.box.zip greetings Edited August 23, 2018 by josephien donated 10$ Link to comment Share on other sites More sharing options...
MaLd0n Posted August 23, 2018 Author Share Posted August 23, 2018 6 hours ago, P1aton0FF said: Nope. I get "no signal" if platform-id 59120000 fake id 59128086 With fakeid 1912 and 3E92 and any platform-id - is loaded, but "Graphics driver failed to load: could not register with framebuffer driver". Have a panic if platform-id 59120003. Platform Platform-ID 3e920003 Fake ID empty - loading, but "Graphics driver failed to load: could not register with framebuffer driver". I tried 18.1, 18.2, 18.3... Tried BBCoffee630.kext, AppleIntelKBLGraphicsFramebufferInjector_3e9x.kext - without results. Send me Aleksandrs-iMac.zip try, put two files in clover/acpi/patched remove all flags etc about video Arquivo Comprimido.zip 24 minutes ago, josephien said: @ Madlon here is the runme zip file, can you verify the dsdt and patch it for me? I'm running 10,13,6 on msi z170a gaming m7 with an i5 7600k on stock (planning overclock later) there's one 16gb memory stick and booting of an ssd Send me Marcs-iMac.fritz.box.zip greetings DSDT.aml.zip Link to comment Share on other sites More sharing options...
Danual Posted August 23, 2018 Share Posted August 23, 2018 (edited) hi, installed an rx570 and its running ok but how do I know or get hardware acceleration running please. thank you Send me Hack-a-Mac.zip Edited August 23, 2018 by Danual Link to comment Share on other sites More sharing options...
MaLd0n Posted August 23, 2018 Author Share Posted August 23, 2018 16 minutes ago, Danual said: hi, installed an rx570 and its running ok but how do I know or get hardware acceleration running please. thank you Send me Hack-a-Mac.zip https://github.com/acidanthera/WhateverGreen 1 Link to comment Share on other sites More sharing options...
fryysyd Posted August 24, 2018 Share Posted August 24, 2018 (edited) @MaLd0n Send me iMac.zip Hello, moderator, dsdt can also add SSD, HDD and wireless network card information, thank you very much! Edited August 24, 2018 by fryysyd supplement Link to comment Share on other sites More sharing options...
boba Posted August 24, 2018 Share Posted August 24, 2018 MaLd0n, need your help! Asrock Z97E-itx, i7-4790k, Intel GPU Barely boot into High Sierra, no ethernet, audio, don't recognize any USB drive... Thanks! Send me Haswells-iMac.zip Link to comment Share on other sites More sharing options...
MaLd0n Posted August 24, 2018 Author Share Posted August 24, 2018 5 hours ago, fryysyd said: @MaLd0n Send me iMac.zip Hello, moderator, dsdt can also add SSD, HDD and wireless network card information, thank you very much! u have a very wrong config DSDT.aml.zip use change EC0 to EC 4543305f 45435f5f change GFX0 to IGPU 47465830 49475055 change HDAS to HDEF 48444153 48444546 change HECI to IMEI 48454349 494d4549 change SAT0 to SATA 53415430 53415441 change GLAN to GIGE 474c414e 47494745 Link to comment Share on other sites More sharing options...
MaLd0n Posted August 24, 2018 Author Share Posted August 24, 2018 10 minutes ago, boba said: MaLd0n, need your help! Asrock Z97E-itx, i7-4790k, Intel GPU Barely boot into High Sierra, no ethernet, audio, don't recognize any USB drive... Thanks! Send me Haswells-iMac.zip CLOVER.zip Link to comment Share on other sites More sharing options...
macw00t Posted August 24, 2018 Share Posted August 24, 2018 (edited) in the recent past (sierra onwards) I was forced to use F6 bios, even making sure to hex edit my mac address in! No matter what I tried couldn't boot without F6 bios. it would be fine if it wasn't so prone to BOOT entry issues etc.... I saw your thread method, and wanted to give it a try..Im booting into Mojave and High Sierra (albeit in safe mode) using newest BIOS! I just need a little help getting DSDT patched. I ran the sendme.app and my hardware info is below. Hope this is sufficient if not I will add anything else I may need. Sincere thanks for any help I may receive! ===================================== HW SPECS: Motherboard: Gigabyte Z170XPSLI rev1.0 firmware: newest (22f) cpu: Intel i5 6500 3.2ghz --> ssdtprgen.sh generated ssdt.aml attatched GFX: NVIDIA GTX1060 6gb / edit: no longer worried about intelHD gfx misc: USB-inject 100 series: I have already made a custom patched USB-inject ssdt that I use with usb-inject-all.kext I can attach that as well. (SSDT-UIAC.aml) Not sure what the most efficient setup is for me anymore so at the very least a customized DSDT and any important flags / patches / settings for clover that will probably go a long way for me. Thanks again for any help! ssdt.aml SSDT-UIAC.aml Send me Carloss-iMac.zip Edited August 24, 2018 by macw00t edit..figured out some things and have decided I only need to try and create a custom DSDT for my needs, focusing on 10.13.6. also edited for brevity, readability etc Link to comment Share on other sites More sharing options...
striimer Posted August 25, 2018 Share Posted August 25, 2018 Hi, need bit help or pointing into the right direction. I'm trying patch Lenovo 720 battery and seems suitable patch is already available for Lenovo 480, seems exactly the same bits 16 and 32. After patching DSDT i'm getting errors, can't compile. Another problem is nvram, brightness is always after reboot 3/4 of max. Tried Aptiomemorifix and now Aptiofixdrv + emuvariable, deleted early nvram.plist , but still the same, always 3/4 of brightness. Attached clover folder, ioreg and lenovo480_patch for the battery. Help appreciated. Hardware: Lenovo 720 i5-7200 8 gb ram 256gb nvme ssd HD620, 1080p Sierra 10.12.6. files.zip Link to comment Share on other sites More sharing options...
MaLd0n Posted August 25, 2018 Author Share Posted August 25, 2018 9 hours ago, macw00t said: in the recent past (sierra onwards) I was forced to use F6 bios, even making sure to hex edit my mac address in! No matter what I tried couldn't boot without F6 bios. it would be fine if it wasn't so prone to BOOT entry issues etc.... I saw your thread method, and wanted to give it a try..Im booting into Mojave and High Sierra (albeit in safe mode) using newest BIOS! I just need a little help getting DSDT patched. I ran the sendme.app and my hardware info is below. Hope this is sufficient if not I will add anything else I may need. Sincere thanks for any help I may receive! ===================================== HW SPECS: Motherboard: Gigabyte Z170XPSLI rev1.0 firmware: newest (22f) cpu: Intel i5 6500 3.2ghz --> ssdtprgen.sh generated ssdt.aml attatched GFX: NVIDIA GTX1060 6gb / edit: no longer worried about intelHD gfx misc: USB-inject 100 series: I have already made a custom patched USB-inject ssdt that I use with usb-inject-all.kext I can attach that as well. (SSDT-UIAC.aml) Not sure what the most efficient setup is for me anymore so at the very least a customized DSDT and any important flags / patches / settings for clover that will probably go a long way for me. Thanks again for any help! ssdt.aml SSDT-UIAC.aml Send me Carloss-iMac.zip CLOVER.zip Link to comment Share on other sites More sharing options...
MaLd0n Posted August 25, 2018 Author Share Posted August 25, 2018 3 hours ago, striimer said: Hi, need bit help or pointing into the right direction. I'm trying patch Lenovo 720 battery and seems suitable patch is already available for Lenovo 480, seems exactly the same bits 16 and 32. After patching DSDT i'm getting errors, can't compile. Another problem is nvram, brightness is always after reboot 3/4 of max. Tried Aptiomemorifix and now Aptiofixdrv + emuvariable, deleted early nvram.plist , but still the same, always 3/4 of brightness. Attached clover folder, ioreg and lenovo480_patch for the battery. Help appreciated. Hardware: Lenovo 720 i5-7200 8 gb ram 256gb nvme ssd HD620, 1080p Sierra 10.12.6. files.zip DSDT.aml.zip apple battery patch manual way Link to comment Share on other sites More sharing options...
striimer Posted August 25, 2018 Share Posted August 25, 2018 (edited) 5 hours ago, MaLd0n said: DSDT.aml.zip apple battery patch manual way Attached dsdt did not cure the battery percentage, it's still "X" on titlebar. When i use my DSDT (not battery patched), then at least charging status was recognised, if AC adapter plugged or not, took 2 screenshots. When i'm using MaLd0n patched DSDT, battery status and charging status are unknown, took third screenshot. Edited August 25, 2018 by striimer Link to comment Share on other sites More sharing options...
MaLd0n Posted August 25, 2018 Author Share Posted August 25, 2018 apply a battery patch, have a guide for it, RM made a good guide Link to comment Share on other sites More sharing options...
MaLd0n Posted August 25, 2018 Author Share Posted August 25, 2018 UPDATE FIRST POST -Folders.app Link to comment Share on other sites More sharing options...
striimer Posted August 25, 2018 Share Posted August 25, 2018 (edited) 6 hours ago, MaLd0n said: apply a battery patch, have a guide for it, RM made a good guide Seems not easy, i'll better donate, can you patch the dsdt ? Edited August 25, 2018 by striimer Link to comment Share on other sites More sharing options...
macw00t Posted August 25, 2018 Share Posted August 25, 2018 18 hours ago, MaLd0n said: CLOVER.zip Just a quick reply to say its working great! Many Thanks for the help; your modern install method(s) are the top tier especially for us scrub hackintoshers! (Now to go help myself and see if i can learn some more and maybe try patching the raw DSDT myself to see if I can get it to match yours )...Cheers! Link to comment Share on other sites More sharing options...
MaLd0n Posted August 25, 2018 Author Share Posted August 25, 2018 28 minutes ago, macw00t said: Just a quick reply to say its working great! Many Thanks for the help; your modern install method(s) are the top tier especially for us scrub hackintoshers! (Now to go help myself and see if i can learn some more and maybe try patching the raw DSDT myself to see if I can get it to match yours )...Cheers! just enjoy! Link to comment Share on other sites More sharing options...
MaLd0n Posted August 25, 2018 Author Share Posted August 25, 2018 50 minutes ago, striimer said: Seems not easy, i'll better donate, can you patch the dsdt ? send me new dump with my DSDT RunMe.app Link to comment Share on other sites More sharing options...
Mikentosh2016 Posted August 25, 2018 Share Posted August 25, 2018 (edited) On 8/22/2018 at 3:29 PM, MaLd0n said: On 8/22/2018 at 3:19 PM, Mikentosh2016 said: I found the issue. FireWire board failure.pdf wow Received / installed the card today and Time Machine backed 4Gb in a short time. Thanks MaLd0n, for your help. Edited August 25, 2018 by Mikentosh2016 1 Link to comment Share on other sites More sharing options...
striimer Posted August 25, 2018 Share Posted August 25, 2018 8 minutes ago, MaLd0n said: send me new dump with my DSDT RunMe.app Dumps done, attached. Send me users-Air.zip Link to comment Share on other sites More sharing options...
Mikentosh2016 Posted August 26, 2018 Share Posted August 26, 2018 4 hours ago, Mikentosh2016 said: wow I spoke too soon. I contacted OWC to determine if the RAID also experienced burned electronics but while I'm waiting for their reply, can you take another look at my Send me iMac? 5 hours ago, Mikentosh2016 said: wow And the Send me iMac https://www59.zippyshare.com/v/kLIWMtS1/file.html Link to comment Share on other sites More sharing options...
fryysyd Posted August 26, 2018 Share Posted August 26, 2018 On 8/24/2018 at 11:11 PM, MaLd0n said: u have a very wrong config DSDT.aml.zip use change EC0 to EC 4543305f 45435f5f change GFX0 to IGPU 47465830 49475055 change HDAS to HDEF 48444153 48444546 change HECI to IMEI 48454349 494d4549 change SAT0 to SATA 53415430 53415441 change GLAN to GIGE 474c414e 47494745 @MaLd0n thank you for your help! I have modified it as you said. Config.plist. However, there is a problem with sleep awakening at present. It seems to be related to USB. I have used the USB related patch, but the problem remains. So would you like to ask if you have SSDT-UIAC.aml from ASUS ROG STRIX Z370-I GAMING? Link to comment Share on other sites More sharing options...
Recommended Posts