bocajoe Posted April 7, 2018 Share Posted April 7, 2018 (edited) 11 minutes ago, MaLd0n said: Jus enable patch for 10.13.4+ and disable other I'm not sure how to enable patch or what to disable other. Sorry, I wish I was better at this, but I am trying to and love to learn. 8 minutes ago, bocajoe said: I'm not sure how to enable patch or what to disable other. Sorry, I wish I was better at this, but I am trying to and love to learn. I also put back the RX460 4GB that was working with USB 3.0 and USB 3.0 still does not work. So I guess me swapping cards wasn't the issue. Any ideas? For some reason USB 3.0 just stopped working Edited April 7, 2018 by bocajoe Link to comment Share on other sites More sharing options...
MaLd0n Posted April 7, 2018 Author Share Posted April 7, 2018 check patches in KextsToPatches in Kernel and Kext Patches tab 1 Link to comment Share on other sites More sharing options...
telepati Posted April 7, 2018 Share Posted April 7, 2018 (edited) @MaLd0n my IMEI controller stop working. I also changed graphics card to RX560. Should we change anything on DSDT? I am using WhateverGreen and Lilu for RX560. https://www112.zippyshare.com/v/INVTcC17/file.html Edited April 7, 2018 by telepati Link to comment Share on other sites More sharing options...
strakm39 Posted April 7, 2018 Share Posted April 7, 2018 I updated Bootloader but still panics with your clover Link to comment Share on other sites More sharing options...
MaLd0n Posted April 7, 2018 Author Share Posted April 7, 2018 1 hour ago, telepati said: @MaLd0n my IMEI controller stop working. I also changed graphics card to RX560. Should we change anything on DSDT? I am using WhateverGreen and Lilu for RX560. https://www112.zippyshare.com/v/INVTcC17/file.html IMEI load only if IntelHDGraphics is enable 1 hour ago, strakm39 said: I updated Bootloader but still panics with your clover use old driver, remove aptiomemoryfix 1 Link to comment Share on other sites More sharing options...
telepati Posted April 7, 2018 Share Posted April 7, 2018 23 minutes ago, MaLd0n said: IMEI load only if IntelHDGraphics is enable Thank you I didn't know that. Link to comment Share on other sites More sharing options...
bocajoe Posted April 7, 2018 Share Posted April 7, 2018 3 hours ago, MaLd0n said: check patches in KextsToPatches in Kernel and Kext Patches tab Here are my patches in KextsToPatches. I'm not 100% sure what to look for. Does anything look incorrect? My RunMe Results: https://drive.google.com/file/d/1UCFEbshe1OEIZDPMjwHyXHntDKZb8iE5/view?usp=sharing Link to comment Share on other sites More sharing options...
strakm39 Posted April 7, 2018 Share Posted April 7, 2018 (edited) MaLdOn I replaced the aptiomemoryfix.efi in your clover folder with the one from mine that boots ok. It still panics when using your clover. Any ideas? Edited April 7, 2018 by strakm39 Link to comment Share on other sites More sharing options...
MaLd0n Posted April 7, 2018 Author Share Posted April 7, 2018 25 minutes ago, bocajoe said: Here are my patches in KextsToPatches. I'm not 100% sure what to look for. Does anything look incorrect? My RunMe Results: https://drive.google.com/file/d/1UCFEbshe1OEIZDPMjwHyXHntDKZb8iE5/view?usp=sharing config.plist.zip 8 minutes ago, strakm39 said: MaLdOn I replaced the aptiomemoryfix.efi in your clover folder with the one from mine that boots ok. It still panics when using your clover. Any ideas? try drop dsdt 1 Link to comment Share on other sites More sharing options...
strakm39 Posted April 8, 2018 Share Posted April 8, 2018 MaLdOn, Still panics Link to comment Share on other sites More sharing options...
bocajoe Posted April 8, 2018 Share Posted April 8, 2018 2 hours ago, MaLd0n said: 2 hours ago, bocajoe said: config.plist.zip As always Maldon... "IT WORKED!!!!!!!" MY USB 3.0 is working again with the config.plist you sent. Many thanks my friend!!!!!!!!! Link to comment Share on other sites More sharing options...
MaLd0n Posted April 8, 2018 Author Share Posted April 8, 2018 2 hours ago, strakm39 said: MaLdOn, Still panics press barspace in clover boot screen and block AppleAlc and Lilu kexts 10 minutes ago, bocajoe said: As always Maldon... "IT WORKED!!!!!!!" MY USB 3.0 is working again with the config.plist you sent. Many thanks my friend!!!!!!!!! enjoy 1 Link to comment Share on other sites More sharing options...
strakm39 Posted April 8, 2018 Share Posted April 8, 2018 MaLdOn, Blocking those two kexts and it still panics. Im finished for the day. Thanks for your help Link to comment Share on other sites More sharing options...
Check-IN Posted April 8, 2018 Share Posted April 8, 2018 (edited) 22 hours ago, MaLd0n said: extract original and apply ur patches i don't use this method, clone, no idea u need use it to avoid this problem change H_EC to EC 485f4543 45435f5f Ok Maldon, I found a DSDT for a model very similar to my notebook, I tried to start with that and I do not have kernel panic, there are some errors that are reported at boot but it works ... What I'm asking you is if you can figure out what was changed to eliminate the initial panic kernel problem. So you can correct my original in the same way. I am attaching both dsdt, if you need more information write me, if it's something you can do I'll be grateful WORKING DSDT.aml ORIGINAL DSDT.aml P.S. the H_EC to EC not change anything Edited April 8, 2018 by gigibatt Link to comment Share on other sites More sharing options...
buyjoey Posted April 8, 2018 Share Posted April 8, 2018 Hi, @MaLd0n I made a question in the wrong forum title. So I will put here the question again. Here are my Runme and IOReg. If you see the screenshot. There are the Preperal function of my LG Monitor(Camera, Audio, Brightness control etc.) But After Slee/Wake, Those are gone away. If I want those back, I need to turn off the computer completely. The monitor connected by TH3 adaptor since my monitor only has the TH3 connector. Could you help me? I run you runme app without any DSDT or SSDT. IOREG.zip https://www40.zippyshare.com/v/aHt4ZlRB/file.html Runme file https://www98.zippyshare.com/v/FxvN6VvG/file.html Thank you!! Your dedication is always amazing for us! Joe. Link to comment Share on other sites More sharing options...
MaLd0n Posted April 8, 2018 Author Share Posted April 8, 2018 4 minutes ago, buyjoey said: Hi, @MaLd0n I made a question in the wrong forum title. So I will put here the question again. Here are my Runme and IOReg. If you see the screenshot. There are the Preperal function of my LG Monitor(Camera, Audio, Brightness control etc.) But After Slee/Wake, Those are gone away. If I want those back, I need to turn off the computer completely. The monitor connected by TH3 adaptor since my monitor only has the TH3 connector. Could you help me? I run you runme app without any DSDT or SSDT. IOREG.zip https://www40.zippyshare.com/v/aHt4ZlRB/file.html Runme file https://www98.zippyshare.com/v/FxvN6VvG/file.html Thank you!! Your dedication is always amazing for us! Joe. check here, bro https://github.com/the-darkvoid/macOS-IOElectrify/ Link to comment Share on other sites More sharing options...
buyjoey Posted April 8, 2018 Share Posted April 8, 2018 1 hour ago, MaLd0n said: check here, bro https://github.com/the-darkvoid/macOS-IOElectrify/ Hello, The kext is not working for my issue. The functions are not coming back after sleep/wake still. Any other method possibility? Link to comment Share on other sites More sharing options...
newphase Posted April 9, 2018 Share Posted April 9, 2018 On 4/7/2018 at 7:02 AM, MaLd0n said: replace, reboot, enter in bios put Internal Graphics to Enable CLOVER.zip Works great! Thank you MaLd0n Link to comment Share on other sites More sharing options...
zzmadd Posted April 9, 2018 Share Posted April 9, 2018 Hi MaLd0n, can you gently make dsdt? Here is the Send Me output: https://mab.to/a2SZlPxHc Link to comment Share on other sites More sharing options...
MaLd0n Posted April 9, 2018 Author Share Posted April 9, 2018 20 hours ago, buyjoey said: Hello, The kext is not working for my issue. The functions are not coming back after sleep/wake still. Any other method possibility? no idea, need check it 8 hours ago, newphase said: Works great! Thank you MaLd0n welcome 43 minutes ago, zzmadd said: Hi MaLd0n, can you gently make dsdt? Here is the Send Me output: https://mab.to/a2SZlPxHc use previous file, u dont need one dsdt for every system or install, dsdt is a bios table Link to comment Share on other sites More sharing options...
zzmadd Posted April 9, 2018 Share Posted April 9, 2018 20 minutes ago, MaLd0n said: no idea, need check it welcome use previous file, u dont need one dsdt for every system or install, dsdt is a bios table but the system wouldn't boot with it, as I remove it, it does boot. Link to comment Share on other sites More sharing options...
MaLd0n Posted April 9, 2018 Author Share Posted April 9, 2018 1 hour ago, zzmadd said: but the system wouldn't boot with it, as I remove it, it does boot. u need use a full clover folder, have many dependencies in oem ssdts Link to comment Share on other sites More sharing options...
camillionario Posted April 9, 2018 Share Posted April 9, 2018 Hello Maldon, Is it necessary to use ssdtPRGen and freqVectorsEdit? Thank you Link to comment Share on other sites More sharing options...
MaLd0n Posted April 9, 2018 Author Share Posted April 9, 2018 8 minutes ago, camillionario said: Hello Maldon, Is it necessary to use ssdtPRGen and freqVectorsEdit? Thank you No, only plug in type, is a very old patch found in MacPro6,1 real tables Link to comment Share on other sites More sharing options...
camillionario Posted April 9, 2018 Share Posted April 9, 2018 refers to this: So it is not necessary to use ssdt-cpupm in Skylake? 1 Link to comment Share on other sites More sharing options...
Recommended Posts