greenman100 Posted October 31, 2006 Share Posted October 31, 2006 Same with me ! 10.4.7 boots fine with DVD(SATA-Converter) on the yellow ports.It seems they compiled the kernel without generic ide support or so. May it be possible to get the 10.4.8 kernel working on an already installed jas 10.4.7(updated to 10.4.8.) ? works for me with 965, but you have to use a USB to IDE converter for the DVD Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221235 Share on other sites More sharing options...
Magicman Posted October 31, 2006 Share Posted October 31, 2006 Interesting I have both a sata and an standard ide hard drive in this machine. Maybe I should install it to the IDE drive...... I'll do that and let you know. Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221236 Share on other sites More sharing options...
hiroo Posted October 31, 2006 Share Posted October 31, 2006 curlyboy, seems we have a similar setup except for the processor. on my first try with semthex kernel I couldn't get radeon x1000 drivers loaded, so had mouse tearing and stuck at 1024x768 and no QE/CI. Did you get this stuff working and what did you do? Thanks. Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221237 Share on other sites More sharing options...
julian23 Posted October 31, 2006 Share Posted October 31, 2006 works for me with 965, but you have to use a USB to IDE converter for the DVD This works ? But why does it work for me with JaS 10.4.7 Release with the DVD on the ICH8 ? Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221240 Share on other sites More sharing options...
curlyboy Posted October 31, 2006 Share Posted October 31, 2006 curlyboy, seems we have a similar setup except for the processor. on my first try with semthex kernel I couldn't get radeon x1000 drivers loaded, so had mouse tearing and stuck at 1024x768 and no QE/CI. Did you get this stuff working and what did you do? Thanks. Hi m8 I just installed the dvd as normal my gfx card was working fine after install quartz and core but no res change until i installed neophus 3.5 pkg after that all perfect Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221242 Share on other sites More sharing options...
greenman100 Posted October 31, 2006 Share Posted October 31, 2006 This works ? But why does it work for me with JaS 10.4.7 Release with the DVD on the ICH8 ? no idea, I don't have 10.4.7 but IDE to USB adapters are cheap Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221246 Share on other sites More sharing options...
JaS Posted October 31, 2006 Share Posted October 31, 2006 If you have an issue with needing the dvd to boot,its because you installed 10.4.8 on to a second partition on the same drive you already have OSX installed on,and its making the partition active that DOES not load the darwin bootloader,fix it by A)installing from the dvd onto your first partition or using the dvd to bless your original os x install and using the darwin bootloader to pickt hat partition. About this mac is crashing for some ppl,nothing I can do about it till someone fixes it. GMA900.950 if its not working , rerun the pkg and it should work after you repair permissions. anyone having boot issues with the extensions.mkext tell me whats giving you the problems and I will make you a new mkext for the dvd. but not link load errors,panics. Hi m8I just installed the dvd as normal my gfx card was working fine after install quartz and core but no res change until i installed neophus 3.5 pkg after that all perfect Glad you got it working.I didn't include any atix1xxx patches so yeah you would have to edit atindrv yourself or use the installer. Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221248 Share on other sites More sharing options...
Magicman Posted October 31, 2006 Share Posted October 31, 2006 That's not true... I totally wiped out my partition table and reformated the entire disk before I installed..... I wanted a clean install and I only had one partition on the drive... I get that blinking cursor still. Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221252 Share on other sites More sharing options...
curlyboy Posted October 31, 2006 Share Posted October 31, 2006 If you have an issue with needing the dvd to boot,its because you installed 10.4.8 on to a second partition on the same drive you already have OSX installed on,and its making the partition active that DOES not load the darwin bootloader,fix it by A)installing from the dvd onto your first partition or using the dvd to bless your original os x install and using the darwin bootloader to pickt hat partition.About this mac is crashing for some ppl,nothing I can do about it till someone fixes it. GMA900.950 if its not working , rerun the pkg and it should work after you repair permissions. anyone having boot issues with the extensions.mkext tell me whats giving you the problems and I will make you a new mkext for the dvd. but not link load errors,panics. Glad you got it working.I didn't include any atix1xxx patches so yeah you would have to edit atindrv yourself or use the installer. Hi jas m8 great job I cant boot without dvd and i have installed to a second physical drive ( sata ii ) Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221253 Share on other sites More sharing options...
VacTacks11 Posted October 31, 2006 Share Posted October 31, 2006 My install (remember I had the install stuck on "Running Essentials Installer Script" with the mikfi kernel) went fine after re-installing with the semthex kernel. However, even though I created a FAT32 Primary Active partition (in front of of the current NTFS partition) I couldn't get OS X to boot. In other words, when I re-started my computer it booted straight to Windows. The Arconis Disk Director didn't see OS X as a valid install. Any ideas? Should I have created the FAT32 Primary Active partition after the current NTFS partition? Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221254 Share on other sites More sharing options...
jan_187 Posted October 31, 2006 Share Posted October 31, 2006 JaS, I also have 1 HD and I let the Mac Disk Util totally whipe it. And then made 1 HFS+ partition with it and installed OSX on it. Something is wrong. I did not have this problem with the 10.4.7 DVD. I already tried the Bles and the Fdisk thing and they do not work. It only works when I boot from DVD. Hope someone will find the cause and fix it Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221255 Share on other sites More sharing options...
julian23 Posted October 31, 2006 Share Posted October 31, 2006 no idea, I don't have 10.4.7 but IDE to USB adapters are cheap Ok, as soon as i get to my local hardware dealer i buy one. they are about 10-15 euros here in germany. what model do you use ? Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221256 Share on other sites More sharing options...
consolation Posted October 31, 2006 Share Posted October 31, 2006 If you have an issue with needing the dvd to boot,its because you installed 10.4.8 on to a second partition on the same drive you already have OSX err.. i wish that was true.. 1) I formatted with Actronix DD, set partition to active. 2) erased and crated an HFS+ partition w/ disk utility 3) installed 10.4.8 MBR error on boot. ATM, trying to see if installing 10.4.6 then "upgrading" it will work better... Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221257 Share on other sites More sharing options...
greenman100 Posted October 31, 2006 Share Posted October 31, 2006 Ok, as soon as i get to my local hardware dealer i buy one. they are about 10-15 euros here in germany. what model do you use ? the number ont he circuit board is PA-923 Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221258 Share on other sites More sharing options...
julian23 Posted October 31, 2006 Share Posted October 31, 2006 the number ont he circuit board is PA-923 thanks. ok, i will pick someone in the store. there should be no big differences with these converters. where is your sata connected to ? ICH8 ? Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221263 Share on other sites More sharing options...
greenman100 Posted October 31, 2006 Share Posted October 31, 2006 thanks. ok, i will pick someone in the store. there should be no big differences with these converters.where is your sata connected to ? ICH8 ? I only have ICH8 SATA ports Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221267 Share on other sites More sharing options...
julian23 Posted October 31, 2006 Share Posted October 31, 2006 I only have ICH8 SATA ports which mainboard do you use ? well, if you only have the ICH8 you must have slow HD rw-performance ? Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221269 Share on other sites More sharing options...
MarkW Posted October 31, 2006 Share Posted October 31, 2006 GMA900.950 if its not working , rerun the pkg and it should work after you repair permissions. Thanks for all the hard work JaS, and hope I don't sound stupid, but what pkg are you referring to? Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221270 Share on other sites More sharing options...
dubhead Posted October 31, 2006 Share Posted October 31, 2006 My expiriences sofar ..Intel915.kext gives me permission error even fixing it via chown -R root:wheel..had to get my old IONetworking.kext inn to have Network. OpenGL is poor no QE/CI on GMA900 chipset. Even after reinstalling the GMA900.950.package i get this .kext cannot be used please reinstall bla bla Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221271 Share on other sites More sharing options...
Synthology Posted October 31, 2006 Share Posted October 31, 2006 Installed on Core2Duo system (in my sig) even with the DVD in the drive and past the count down, cannot find "boot.apple.plist" this was with the Mifki kernel installed. Same thing with semthex install. without DVD, the usual blinking cursor. Partition was made active, and blessed. Still no go. Please advise. Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221274 Share on other sites More sharing options...
Clonk Posted October 31, 2006 Share Posted October 31, 2006 No joy so far. Booting mifki loads the kernel, but then panics before going into graphics mode (I suspect my system doesn't support one or more of the needed features, but I thought "Just give it a try" Booting semthex gets me a bit further, until "still waiting for root device" appears. Then it just sits there. Next step should be to rearrange the drives as outlined by Rammjet in many posts regarding this problem. It was not neccessary for the JaS 1.4.7 install, but you never know. Thanks again all for your hard work; JaS, mifki, semtex and Rammjet. Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221277 Share on other sites More sharing options...
Kaspers Posted October 31, 2006 Share Posted October 31, 2006 When I boot with DVD my PC just crashes and reboots... C2D E6600 Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221280 Share on other sites More sharing options...
Jedisinclair Posted October 31, 2006 Share Posted October 31, 2006 JaS (and everyone else)... I too installed on a single, clean partition and I get the blinking cursor. Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221282 Share on other sites More sharing options...
bgrau Posted October 31, 2006 Share Posted October 31, 2006 Managed to boot. Cool... I upgraded from the previous OSX (JaS 10.4.8 combo). Used from a vmware install to a native (physical disk) install. Despite error message at end of installation 100%, but without optimizing as it should: It works well for running most apps apart from MS Office (it says i need to reinstall because some libraries have changed places, which is no big deal i guess). Even iCal works unlike some dudes... About gives the relaunch. System Profiler gave hardware error msg, but easily fixed with Colonel patch based on replacing System Profiler from 10.4.7. ATI x1600 not recognised and no qe/ci (will try Boris/neopheus patch) Only main issue is network card, thats a bummer for me... I have two network cards, one for LAN and one for cable modem. The one for cable modem is fine and dandy, since I am on Internet writing this, the LAN one in System Prefs/Netwotk, it shows it iconized in red and says: The cable for PCI ethernet slot is not plugged in. I would like help to fix this, for me its more important than other issues. Thank you very much JaS, Semthex, and Mifki and all others for this, now comes debugging time lol... Btw, how do we check the kernel version in terminal (since About is not working)? Cheers Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221283 Share on other sites More sharing options...
JaS Posted October 31, 2006 Share Posted October 31, 2006 Ok so it seems that you all have a different md5 sums then me.I would guess the torrent got poisoned by the 5 fake seeds.That is out of my control. before any of you start to {censored} about downloading the dvd , I wasted a lot more time making it and trying to get it out to you.So f***ing save it. I have to think about what to do next to try and clean up this God damned mess now. Link to comment https://www.insanelymac.com/forum/topic/31698-jas-1048-intel-sse3-only-dvd-install-discussion/page/6/#findComment-221284 Share on other sites More sharing options...
Recommended Posts