dip95 Posted May 8, 2016 Share Posted May 8, 2016 My trying based on this guide http://www.insanelymac.com/forum/topic/310098-el-capitan-install-preparation/ after create usb, in boot stacked on this error: launchd service exited with abnormal code 255, used AMD_10.11.2_FX_fix-3.zip by spakkk, boot args: -v -f nv_disable=1 npci_0x3000 kext-dev-mode=1, used kext for usb fix : IOUSBFamily.kext.rar Link to comment Share on other sites More sharing options...
spakk Posted May 8, 2016 Share Posted May 8, 2016 write your full hardware specifications in your signature, otherwise nobody will help you! Link to comment Share on other sites More sharing options...
dip95 Posted May 8, 2016 Author Share Posted May 8, 2016 write your full hardware specifications in your signature, otherwise nobody will help you! amd fx 6300 nvidia gtx750 ti asus M5A78L-M LX3 Link to comment Share on other sites More sharing options...
spakk Posted May 8, 2016 Share Posted May 8, 2016 upload your Extra folder, raw DSDT and the ioreg-file Link to comment Share on other sites More sharing options...
dip95 Posted May 9, 2016 Author Share Posted May 9, 2016 upload your Extra folder, raw DSDT and the ioreg-file https://dropmefiles.com/72727 another kernel Link to comment Share on other sites More sharing options...
dip95 Posted May 9, 2016 Author Share Posted May 9, 2016 upload your Extra folder, raw DSDT and the ioreg-file after 5 minutes error ccomplete and boot continue next error: hfs: set VeryLowDisk: vol:untitled, freeblks:0, dangerlimit:12 Link to comment Share on other sites More sharing options...
spakk Posted May 9, 2016 Share Posted May 9, 2016 .....because some things are missing, let me a little time to modify the files, I will upload later the files for your hardware.. Link to comment Share on other sites More sharing options...
dip95 Posted May 9, 2016 Author Share Posted May 9, 2016 .....because some things are missing, let me a little time to modify the files, I will upload later the files for your hardware.. ok thx Link to comment Share on other sites More sharing options...
spakk Posted May 9, 2016 Share Posted May 9, 2016 (edited) In the Annex is located the Extra folder with all drivers and modified boot.plist, did not fully modified the DSDT, installed only patches and adjusted faults, possibly should later patch the USB ...at the moment, I have little time... will make later. Edit: Attention! the kernel is located in to Extra folder, therefore it is not necessary to insert the amd kernel in to S/L/kernels which has the following advantages, after updating on a new Build the amd kernel will not be overwritten. ....after reaching the desktop, then install the Nvidia WebDriver, then change the bootarg of nv_disable=1 to nv_drive=1 ...then your graphics card should work better replace the system.kext from one of my kernel package against the orig. system.kext in S/L/E, which prevents the symbol error that occur during boot. if you should have problems with USB ports, so then write us, or install this USB -Fix ....but read the instructions! Archive.zip Edited May 9, 2016 by spakk 1 Link to comment Share on other sites More sharing options...
dip95 Posted May 9, 2016 Author Share Posted May 9, 2016 In the Annex is located the Extra folder with all drivers and modified boot.plist, did not fully modified the DSDT, installed only patches and adjusted faults, possibly should later patch the USB ...at the moment, I have little time... will make later. Edit: Attention! the kernel is located in to Extra folder, therefore it is not necessary to insert the amd kernel in to S/L/kernels which has the following advantages, after updating on a new Build the amd kernel will not be overwritten. ....after reaching the desktop, then install the Nvidia WebDriver, then change the bootarg of nv_disable=1 to nv_drive=1 ...then your graphics card should work better replace the system.kext from one of my kernel package against the orig. system.kext in S/L/E, which prevents the symbol error that occur during boot. if you should have problems with USB ports, so then write us, or install this USB -Fix ....but read the instructions! thx for help but still a same error( hfs: verylowdisk... maybe its cause my flashdrive have 8g? Link to comment Share on other sites More sharing options...
spakk Posted May 9, 2016 Share Posted May 9, 2016 sory, I have not noticed your error message.... Yes, the HDD or USB flash disk which you booting OS X causing the problems, possible is the HDD or USB Flash Disk full or defective ? use another USB flash disk or an external HDD Link to comment Share on other sites More sharing options...
dip95 Posted May 9, 2016 Author Share Posted May 9, 2016 sory, I have not noticed your error message.... Yes, the HDD or USB flash disk which you booting OS X causing the problems, possible is the HDD or USB Flash Disk full or defective ? use another USB flash disk or an external HDD on usb 10mb free after create it bootable( Link to comment Share on other sites More sharing options...
spakk Posted May 9, 2016 Share Posted May 9, 2016 do you have possibly a small external HDD that you can use as OS X Installer?....it is better to use another USB Flash Disk or an another HDD, your USB flash disk is the cause of the problem!!! Link to comment Share on other sites More sharing options...
dip95 Posted May 10, 2016 Author Share Posted May 10, 2016 do you have possibly a small external HDD that you can use as OS X Installer?....it is better to use another USB Flash Disk or an another HDD, your USB flash disk is the cause of the problem!!! omg again this error when i tryed to install from hdd((( Link to comment Share on other sites More sharing options...
spakk Posted May 10, 2016 Share Posted May 10, 2016 No problem. 1. check during boot, which Disk or partition is causing this error message. 2. check the HDD's or the partitions that are installed in your system, and disconnect unnecessary HDD's for the installation of OS X from SATA slot. Check the HDD's or partitions whether this have enough disks capacity available ..... roughly >4GB, only one estimated value, without any basis, but it must not be underneath! if this should not help, then make an image of the error message and upload it here. I had the same phenomenon during of the installation of el capitan. The cause was defective sectors on one of my partition and the other time was little hard drive capacity. but it can also be in connection with the USB flash disk, now you need to find where the problem is caused. I hope it will help you further. Link to comment Share on other sites More sharing options...
dip95 Posted May 10, 2016 Author Share Posted May 10, 2016 No problem. 1. check during boot, which Disk or partition is causing this error message. 2. check the HDD's or the partitions that are installed in your system, and disconnect unnecessary HDD's for the installation of OS X from SATA slot. Check the HDD's or partitions whether this have enough disks capacity available ..... roughly >4GB, only one estimated value, without any basis, but it must not be underneath! if this should not help, then make an image of the error message and upload it here. I had the same phenomenon during of the installation of el capitan. The cause was defective sectors on one of my partition and the other time was little hard drive capacity. but it can also be in connection with the USB flash disk, now you need to find where the problem is caused. I hope it will help you further. first mount untitled part, i dont know what is it i didnt created this part:second: Link to comment Share on other sites More sharing options...
Shaneee Posted May 10, 2016 Share Posted May 10, 2016 Navigate to /System/Installation/Packages on your USB and copy these there replacing what's already there. Archive.zip Link to comment Share on other sites More sharing options...
dip95 Posted May 10, 2016 Author Share Posted May 10, 2016 Navigate to /System/Installation/Packages on your USB and copy these there replacing what's already there. nothing changes Link to comment Share on other sites More sharing options...
Shaneee Posted May 10, 2016 Share Posted May 10, 2016 Was hoping a minimal replace would work. Copy the new package in there then. I've had to do this in the past to get the install running. https://mega.nz/#!D5hkWL7Q!jjXZiIpkYpiV4kCCvQDaRVpixLlhErB1pvj5b1r88fk Link to comment Share on other sites More sharing options...
dip95 Posted May 10, 2016 Author Share Posted May 10, 2016 Was hoping a minimal replace would work. Copy the new package in there then. I've had to do this in the past to get the install running. https://mega.nz/#!D5hkWL7Q!jjXZiIpkYpiV4kCCvQDaRVpixLlhErB1pvj5b1r88fk still the same( Was hoping a minimal replace would work. Copy the new package in there then. I've had to do this in the past to get the install running. https://mega.nz/#!D5hkWL7Q!jjXZiIpkYpiV4kCCvQDaRVpixLlhErB1pvj5b1r88fk when i install 10105 yosemite doing fine, problem with elcapo( still the same( when i install 10105 yosemite doing fine, problem with elcapo( or problem with bootloader Link to comment Share on other sites More sharing options...
Shaneee Posted May 10, 2016 Share Posted May 10, 2016 You're using Enoch r2795 correct? Have you tried safeboot ( -x ) Link to comment Share on other sites More sharing options...
dip95 Posted May 10, 2016 Author Share Posted May 10, 2016 You're using Enoch r2795 correct? Have you tried safeboot ( -x ) with -x infinitely "Invalid kernel opcode (64-bit): 26 6d 8b 00 80 ff ff ff ..... Link to comment Share on other sites More sharing options...
Shaneee Posted May 10, 2016 Share Posted May 10, 2016 Please try the following kernels also using -x http://www.insanelymac.com/forum/topic/309765-amd-os-x-el-capitan-1011-kernel-testing-release-for-help-use-the-help-topic/page-8?do=findComment&comment=2196793 http://www.insanelymac.com/forum/topic/309765-amd-os-x-el-capitan-1011-kernel-testing-release-for-help-use-the-help-topic/?p=2195566 http://amd-osx.com/files/shaneee-rc1.zip Link to comment Share on other sites More sharing options...
dip95 Posted May 10, 2016 Author Share Posted May 10, 2016 Please try the following kernels also using -x http://www.insanelymac.com/forum/topic/309765-amd-os-x-el-capitan-1011-kernel-testing-release-for-help-use-the-help-topic/page-8?do=findComment&comment=2196793 http://www.insanelymac.com/forum/topic/309765-amd-os-x-el-capitan-1011-kernel-testing-release-for-help-use-the-help-topic/?p=2195566 http://amd-osx.com/files/shane i replaced system kext from spakk, how system kext i must use Link to comment Share on other sites More sharing options...
Shaneee Posted May 10, 2016 Share Posted May 10, 2016 Just use the kernel. You should be ok to use the custom System.kext with these kernels. Link to comment Share on other sites More sharing options...
Recommended Posts