Elbeyrouni7 Posted March 29, 2016 Share Posted March 29, 2016 (edited) Hi everybody,I'm trying to inject my graphic card code into the DSDT, I followed the guide http://www.rampagedev.com/?page_id=276&page=15 to no avail (good guide by the way), I'm running El Capitan 10.11.3 and I've already installed NVidia Web drivers with a boot flag nvda_drv=1 along with NVidia injection. My system definition is iMac 11,3 because it's the closest regarding to my CPU. I'm using the port "PCIEX1_1" for my Wi-Fi Card TP-Link TL-WDN4800, and the port "PCIEX16" for my GTX 550 Ti.Please see the attachments for my DSDT and IOReg files along with two screenshots.Could someone please help me doing that, by answering the following questions:Is the code of the guide above still correct?If so, in which line should I inject it?Do I have to make other changes in my DSDT file?Thanks, Edited March 29, 2016 by Elbeyrouni7 Please read the rules. Link to comment Share on other sites More sharing options...
Allan Posted March 29, 2016 Share Posted March 29, 2016 So, you just need fix the info in System Preferences right? You have problems with the performance? QE/CI? 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 30, 2016 Author Share Posted March 30, 2016 So, you just need fix the info in System Preferences right? You have problems with the performance? QE/CI? First of all thanks for your quick reply, and yes, in fact, I wanted to inject the graphics code into DSDT to : 1 - Get full QE/CI on my card, 'cause right now I got bad performance even with NVidia web driver, 2- Fix the graphics info in system report (the graphics memory displayed is 1536MB, actually it's 1024MB). Thanks for your help, 1 Link to comment Share on other sites More sharing options...
Allan Posted March 30, 2016 Share Posted March 30, 2016 Ok. What bootloader are you using? Can you send me the original DSDT? Extract again and post here. 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 30, 2016 Author Share Posted March 30, 2016 I'm using Clover and here is my original DSDT. Sorry I couldn't attached it unzipped. Link to comment Share on other sites More sharing options...
Allan Posted March 30, 2016 Share Posted March 30, 2016 Ok. Send me your config.plist too. EDIT: This is not your original DSDT, how do you extract? 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 30, 2016 Author Share Posted March 30, 2016 I'll send you my config.plist within 2 hours the time to be at home and make a copy of it (I'm in my office right now ), and you are right by mistake the DSDT that I sent to you is not the original one, I thought I had it, sorry about that, I'm going to extract it using the guide http://www.insanelymac.com/forum/topic/287011-how-to-extract-and-compile-dsdtaml-with-dsdt-editor/, just one question do I have to follow the whole steps? Link to comment Share on other sites More sharing options...
Allan Posted March 30, 2016 Share Posted March 30, 2016 With Clover, you just need press F4 button in GUI (the inicial part, when you select the partition to boot), after that, boot OS X, and go to EFI/CLOVER/ACPI/patched/origin 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 30, 2016 Author Share Posted March 30, 2016 Thanks Allan , I'm gonna send you both files DSDT original and config.plist, once at home . 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 30, 2016 Author Share Posted March 30, 2016 As promised, here are the files needed. 1 Link to comment Share on other sites More sharing options...
artur_pt Posted March 30, 2016 Share Posted March 30, 2016 hello try this one if u boot attach a ioreg with this dsdt and report DSDT.aml.zip just remember this is a patched dsdt .. so disable all clover dsdt fix good hack 2 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 30, 2016 Author Share Posted March 30, 2016 hello try this one if u boot attach a ioreg with this dsdt and report DSDT.aml.zip just remember this is a patched dsdt .. so disable all clover dsdt fix good hack Thanks Artur_pt, I'm gonna test it, be back soon for the result. Link to comment Share on other sites More sharing options...
Allan Posted March 30, 2016 Share Posted March 30, 2016 I clean your config.plist: config.plist.zip 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 30, 2016 Author Share Posted March 30, 2016 Thanks Artur_pt, I'm gonna test it, be back soon for the result. Hi Artur, I tried the file but unfortunately the mouse and keyboard are not working, I tried all USB ports so I coudn't get to the Desktop, any idea? I clean your config.plist: config.plist.zip Thank you very much Allan for the good job ?, I'll wait for DSDT to make a test.? Link to comment Share on other sites More sharing options...
Allan Posted March 30, 2016 Share Posted March 30, 2016 About your USB, try with this config.plist: config.plist.zip And if you want, try this DSDT: DSDT.aml.zip 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 30, 2016 Author Share Posted March 30, 2016 About your USB, try with this config.plist: config.plist.zip And if you want, try this DSDT: DSDT.aml.zip Thanks Allan, I'm gonna test them and give you a feedback. 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 31, 2016 Author Share Posted March 31, 2016 I have one question between brackets, when I wanted to install El Capitan 10.11.3, the only way to boot into Clover menu was to disable USB3 controller in BIOS, otherwise I got stick with a message Boot1: /boot5 (forever ), so after the installation of El Capitan in legacy mode, I wanted to enable that controller, result Clover won't boot with the same message so until now I'm running El Capitan with USB3 controller disabled in BIOS. Is there any solution for this? P.S. I didn't test yet the last files 'cause I'm still at work right now , sorry if my question needs a new topic. 1 Link to comment Share on other sites More sharing options...
Allan Posted March 31, 2016 Share Posted March 31, 2016 I have one question between brackets, when I wanted to install El Capitan 10.11.3, the only way to boot into Clover menu was to disable USB3 controller in BIOS, otherwise I got stick with a message Boot1: /boot5 (forever ), so after the installation of El Capitan in legacy mode, I wanted to enable that controller, result Clover won't boot with the same message so until now I'm running El Capitan with USB3 controller disabled in BIOS. Is there any solution for this? Check this: http://olarila.com/forum/viewtopic.php?f=28&t=4084 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 31, 2016 Author Share Posted March 31, 2016 Hi Allan, I've tested the files you gave me, but I couldn't get my USB working until I change the devices EHC1 & EHC2 into EH01 & EH02 in the DSDT using MaciASL and now the USB ports are working (I found that on the net) but I don't know if it's really safe for my Motherboard. About my main problem which is Graphics performance, I got the same bad results, maybe I'm missing something, that's why I made a copy of my IOReg using your files, I hope it'll give you an idea about the problem, thanks again. Check this: http://olarila.com/forum/viewtopic.php?f=28&t=4084 Unfortunately Allan my BIOS is not UEFI but Legacy. (old motherboard P55A-UD3 Gigabyte) Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 31, 2016 Author Share Posted March 31, 2016 Hi Artur, I've also tested the file that you gave me, and I had to make the same changes, (EHC1 & EHC2 into EH01 & EH02) in the DSDT, I noticed that with your DSDT the wifi card wasn't working (always searching for a network), and the graphics performance is not better. I think I'm missing something but I don't know what, I made a copy of my IOReg using your file, I hope it'll give you an idea about the problem too, thanks for all. Link to comment Share on other sites More sharing options...
artur_pt Posted March 31, 2016 Share Posted March 31, 2016 hello now the wifi and usb should be working DSDT.aml.zip what i see by ioreg the graphics are in the right place and all loaded good hack 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 31, 2016 Author Share Posted March 31, 2016 hello now the wifi and usb should be working DSDT.aml.zip what i see by ioreg the graphics are in the right place and all loaded good hack Hi Artur, USB ports are working but for the Wifi I got a message 'no hardware installed', and I still have no full acceleration , any idea? Link to comment Share on other sites More sharing options...
artur_pt Posted March 31, 2016 Share Posted March 31, 2016 hello u aren't using a atheros wifi card ? from the ioreg says its a atheros .. is there where i inject it about the graphics .. how are u booting .. injecting nvidia or not ? post another ioreg with the dsdt .. i send u before good hack 1 Link to comment Share on other sites More sharing options...
Elbeyrouni7 Posted March 31, 2016 Author Share Posted March 31, 2016 Hi Artur, I'm using the card mentioned in my signature, TP-Link TL-WDN4800, which is an Atheros based card. Well, I'm going to reinstall all over again, using the last version of Clover and make my own USB installer. Could you tell me which is the best guide? Last time, I used a method from other website, and I want to use the method recommended by insanelymac. About the Graphics, I tried both options for Nvidia inject : No: Black screen (no signal), Yes: I can reach the desktop but with poor performance, to give you an idea (02 Frames/s) with NVidia web driver, (13 Frames/s with Apple default driver). Thanks for all, Link to comment Share on other sites More sharing options...
artur_pt Posted April 1, 2016 Share Posted April 1, 2016 hello see this one Making a 10.10/10.11 USB Installer /w Clover (UEFI and Legacy) the correct way! good hack 1 Link to comment Share on other sites More sharing options...
Recommended Posts