MNSiw Posted October 7, 2015 Share Posted October 7, 2015 I had Snow Leopard, downloaded El Capitan app from store, created 16GB partition on Snow Leopard drive and prepared it as installer because I don't have 16GB data stick, erased Snow Leopard parttion and installed El Capitan to it, it went smooth without any issue. Now I have 2 partitions on drive, Installer and El Capitan, to enable my wireless, fix USB over current issue and proper shutdown and restart I need to disable SIP. If I press and hold Cmd+R after Clover screen it boot to desktop, if I select Recovery HD from Clover boot menu and use 'csrutil disable' it show success messange but after reboot it's still enabled (csrutil status). Is it due to Installer partition or I'm doing it wrong way, thanks. Link to comment Share on other sites More sharing options...
MrGreen Posted October 7, 2015 Share Posted October 7, 2015 To use unsigned kexts during first boot use bootflags rootless=0 and kext-dev-mode=1 The proper way of disable SIP later (I think) is to add to Clover's plist <key>RtVariables</key><dict><key>CsrActiveConfig</key><string>0x67</string><key>BooterConfig</key><string>0x28</string></dict> I found this somewhere in the forum and for me it is working perfectly. 3 Link to comment Share on other sites More sharing options...
MNSiw Posted October 7, 2015 Author Share Posted October 7, 2015 To use unsigned kexts during first boot use bootflags rootless=0 and kext-dev-mode=1 The proper way of disable SIP later (I think) is to add to Clover's plist <key>RtVariables</key> <dict> <key>CsrActiveConfig</key> <string>0x67</string> <key>BooterConfig</key> <string>0x28</string> </dict> I found this somewhere in the forum and for me it is working perfectly. Thanks Green :-) For installer and 1st boot 'boot with injected kexts' worked for me. Now have two issues, wireless kext not loading and showing USB over current error. I found something similar to disable SIP on an other forum, I'll try it. 1 Link to comment Share on other sites More sharing options...
fantomas Posted October 7, 2015 Share Posted October 7, 2015 To use unsigned kexts during first boot use bootflags rootless=0 and kext-dev-mode=1 1) kext-dev-mode is already implemented in rootless 2) rootless is part of SIP now, it's only about enabling/disabling SIP... you don't need any more these flags in El Capitan 1 Link to comment Share on other sites More sharing options...
LoBlanc Posted October 13, 2015 Share Posted October 13, 2015 Doesn't seem to work for me with my EFI (not UEFI) installation doing the following: First boot in clover 3280 with "boot w/o caches and injecting third party kexts" Then change the CSR like above using Clover installer. Save new .plist. Use new plist. Restart. The kexts in Clover/kexts won't inject. Am I missing anything? Using Library/Extensions instead doesn't work neither (yes is an old board (GA P35-DS3R). Link to comment Share on other sites More sharing options...
LoBlanc Posted October 14, 2015 Share Posted October 14, 2015 Well, am I perhaps missing anything obvious? How did you guys managed to get your kexts injected w/o choosing so in clover everytime you start your computer? Link to comment Share on other sites More sharing options...
Phil511 Posted October 14, 2015 Share Posted October 14, 2015 @LoBlanc, Clover 3280 has SIP disabled by default. Try this, in your first boot, install all third party kexts and patched AppleHDA. Use the following URL to get Repair Permissions tool to repair disk permissions. Enable SIP and reboot. Good luck. El Capitan is not the same Mac OS X like what we are use to. Apple has quietly put in a big monkey wrench into the whole OS. Too far we know SIP implementation & also USB. There maybe some more. Try and let us know. That tool as the author explained is specifically design for El Capitan has Apple took out disk utility ( disk repair permissions out of El Capitan). Good luck! https://www.firewolf.science/2015/07/repairpermissions-v2-0-cli/ Link to comment Share on other sites More sharing options...
LoBlanc Posted October 15, 2015 Share Posted October 15, 2015 @Phil511 Thank you for your help. I'll give a try today. Link to comment Share on other sites More sharing options...
LoBlanc Posted October 23, 2015 Share Posted October 23, 2015 @Phil511 I performed a complete new installation and then it worked the way described here ! Thank you for your support. Link to comment Share on other sites More sharing options...
Recommended Posts