frnic Posted August 4, 2015 Share Posted August 4, 2015 I have been running all the betas since 1, and everything has worked fine after I fixed the Kext Injection problem but copying FakeSMC.kext and RealtekRTL81xx,Kext to the S/L/E. Today after updating to beta 6 my ethernet is not working. Suggestions? TIA, Frank I only use FakeSMC.Kext and RealtekRTL81xx.Kext I have tried placing them into /S/L/E and /L/E - the system only boots when they are in /S/L/E, obviously Clover injection is not working and placing them in /L/E results in boot up hanging. I have tried using RealtekRTL8111.Kext instead of RealtekRTL81xx.Kext and get the same results. Suggestions? TIA, Frank Link to comment Share on other sites More sharing options...
copil Posted August 4, 2015 Share Posted August 4, 2015 Mieze driver 2.0.0? RTL8111F-G ? install in /L/E? don't work? -open the terminal -copy the KEXT in /L/E sudo -s chmod -R 755 /Library/Extensions/RealtekRTL8111.kext chown -R root:wheel /Library/Extensions/RealtekRTL8111.kext sudo touch /L*/Extensions Link to comment Share on other sites More sharing options...
frnic Posted August 4, 2015 Author Share Posted August 4, 2015 copil, Thank you for the reply. Previously: RealRTC81xx.kext (not sure if that is the same as you recommended) installed into /S/L/E didn't work changed owner and permissions still didn't work rebuilt cache (touch /drive/System/Library/Extensions) - still didn't work kextcache -Boot -U . - still didn't work Now: Downloaded Mieze driver from github and built it locally using Yosemite/xcode/etc. Installed into /L/E Removed old driver from /S/L/E changed permissions touched /drive/S/L/E kextcache -Boot -U . Still doesn't work. (boots but no ethernet) When I rebuild cache using kextcache -Boot -U . in Yosemite I get the following output in terminal (and EL Capitan will boot - but no ethernet) (Note that the ethernet driver is not mentioned) Franks-iMac:El Capitan Fusion root# touch System/Library/Extensions Franks-iMac:El Capitan Fusion root# kextcache -Boot -U . rebuilding /Volumes/El Capitan Fusion/System/Library/PrelinkedKernels/prelinkedkernel kext-dev-mode allowing invalid signature -67062 0xFFFFFFFFFFFEFA0A for kext LPCSensors.kext kext-dev-mode allowing invalid signature -67062 0xFFFFFFFFFFFEFA0A for kext GPUSensors.kext kext-dev-mode allowing invalid signature -67062 0xFFFFFFFFFFFEFA0A for kext CPUSensors.kext kext-dev-mode allowing invalid signature -67062 0xFFFFFFFFFFFEFA0A for kext ACPISensors.kext kext-dev-mode allowing invalid signature -67062 0xFFFFFFFFFFFEFA0A for kext FakeSMC.kext /System/Library/PrelinkedKernels/prelinkedkernel not cached. Successfully updated disk0s3. Successfully updated disk5s3. If I do the same after booting into 10.11 beta 6 I get this output on terminal - system will no longer boot into 10.11 beta 6 following executing this - note the ethernet kext is listed here. Franks-iMac:El Capitan Fusion root# kextcache -Boot -U . rebuilding //System/Library/PrelinkedKernels/prelinkedkernel Untrusted kexts are not allowed RealtekRTL8111.kext has invalid signature; omitting. Untrusted kexts are not allowed LPCSensors.kext has invalid signature; omitting. Untrusted kexts are not allowed GPUSensors.kext has invalid signature; omitting. Untrusted kexts are not allowed CPUSensors.kext has invalid signature; omitting. Untrusted kexts are not allowed ACPISensors.kext has invalid signature; omitting. Untrusted kexts are not allowed FakeSMC.kext has invalid signature; omitting. /System/Library/PrelinkedKernels/prelinkedkernel not cached. Successfully updated disk0s3. Successfully updated disk5s3. Rebooting into Yosemite and rerunning the kextcache command there fixes things so I can again boot into El Capitan but ethernet still doesn't work Suggestions? TIA, Frank Link to comment Share on other sites More sharing options...
copil Posted August 4, 2015 Share Posted August 4, 2015 SIP are enabled? This post is very special http://www.insanelymac.com/forum/topic/284656-clover-general-discussion/page-365?do=findComment&comment=2156263 <key>RtVariables</key> <dict><key>CsrActiveConfig</key><string>0x67</string><key>BooterConfig</key><string>0x28</string></dict> nvram is enabled? Link to comment Share on other sites More sharing options...
frnic Posted August 4, 2015 Author Share Posted August 4, 2015 coil, Thanks again. I read almost all of that thread and it was very informative. The problem I had is "fixed" for now. I upgraded to Clover 3253 and I now have ethernet. Thanks, Frank 1 Link to comment Share on other sites More sharing options...
Recommended Posts