waqy Posted August 27, 2015 Share Posted August 27, 2015 I've got Yosemite installed which pretty much works perfectly, except that my card shows as AMD 7xxx rather than 7970. I've created a El Capitan USB installer with Clover legacy on it as my machine is not a UEFI-enabled one. The default flags are kext dev mode and rootless something, both enabled. When i select verbose mode, it will start booting up and just after the ++++++++++++++++++++++++ line it will reboot. Is there something I am doing wrong? Same thing happens if I boot the installer using the older version of Clover on the Yosemite HDD CPU: Intel Core i7(can't remember which one)Motherboard: Asus Rampage Extreme IIGPU: AMD Radeon HD 7970 3GB Edit: Yes, mendietinha, I am just at work at the moment, but thought I would make a brief post on here. Full screenshot and config will be posted later on. Link to comment Share on other sites More sharing options...
mendietinha Posted August 27, 2015 Share Posted August 27, 2015 my man, it helps if you post your config properly. 2 Link to comment Share on other sites More sharing options...
waqy Posted August 29, 2015 Share Posted August 29, 2015 I get Sound Assertion error when booting the USB. It's getting further than it was before. Is this related to FakeSMC by any chance? Screenshot attached! Link to comment Share on other sites More sharing options...
TheRacerMaster Posted August 30, 2015 Share Posted August 30, 2015 Do you see DSMOS has arrived anywhere in the bootup process? If so, FakeSMC is not an issue, and it's probably graphics. If not, then FakeSMC is not properly injected/installed. Link to comment Share on other sites More sharing options...
waqy Posted August 30, 2015 Share Posted August 30, 2015 Thanks for the reply TheRacerMaster. So after doing some further research and testing, i finally managed to boot into the installer. I change the OSX version in Clover to 10.11 rather than the default 10.10. whatever. I also booted with rootless=0 and left everything else as normal. I am happy to say I am now typing this from Safari in El capitan Just need to install clover now and get the USB 3.0 ports, and XFI sound card working! Link to comment Share on other sites More sharing options...
TheRacerMaster Posted August 30, 2015 Share Posted August 30, 2015 rootless=0 is deprecated with DP3 and newer, you need to use csr-active-config NVRAM values (AKA CsrActiveConfig in Clover config.plist) to load unsigned kexts or completely disable SIP. You'll probably also want to upgrade you revision of Clover to the latest one. Link to comment Share on other sites More sharing options...
caiquecastro Posted August 30, 2015 Share Posted August 30, 2015 Thanks for the reply TheRacerMaster. So after doing some further research and testing, i finally managed to boot into the installer. I change the OSX version in Clover to 10.11 rather than the default 10.10. whatever. I also booted with rootless=0 and left everything else as normal. I am happy to say I am now typing this from Safari in El capitan Just need to install clover now and get the USB 3.0 ports, and XFI sound card working! Theres too much memory on your PC 0.0 1 Link to comment Share on other sites More sharing options...
waqy Posted August 31, 2015 Share Posted August 31, 2015 Theres too much memory on your PC 0.0 Yeah I know Has anyone got a problem with Sleep on El Capitan? Sleep/wake worked perfectly for me on Yosemite but not on El Capitan, is there a kext I could extract from it to get sleep working? Only thing I need to have a 100% working install.. Link to comment Share on other sites More sharing options...
tluck Posted August 31, 2015 Share Posted August 31, 2015 @waqy yes... i did have a sleep/wake issue - but i fixed with some DSDT tweaks. does it sleep or immediately wake when trying to sleep. you should see the wake reason in the system.log for me, I had to remove some _PRW name/methods from HDEF and GBE devices so it stays asleep. plus renamed EHC1 and EHC2 1 Link to comment Share on other sites More sharing options...
luky35 Posted August 31, 2015 Share Posted August 31, 2015 Who can have the hard drive icon to El Capitan Link to comment Share on other sites More sharing options...
Allan Posted August 31, 2015 Share Posted August 31, 2015 Who can have the hard drive icon to El Capitan You mean this? What happened? Link to comment Share on other sites More sharing options...
luky35 Posted August 31, 2015 Share Posted August 31, 2015 You mean this? HD.png What happened? Yeah, only that disk image of El Capitan. Link to comment Share on other sites More sharing options...
Allan Posted August 31, 2015 Share Posted August 31, 2015 So....the disk icon doesn't appear?? Check if in Finder preferences this option is enabled or not. 1 Link to comment Share on other sites More sharing options...
waqy Posted August 31, 2015 Share Posted August 31, 2015 When I select Sleep it starts to turn off, but doesn't fully turn itself off. The graphics turn off but normally the blue LED on my computer will flash on and off when in sleeps. and the fans will turn off too, What did you change in your DSDT? Mind helping me out if you can? @waqy yes... i did have a sleep/wake issue - but i fixed with some DSDT tweaks. does it sleep or immediately wake when trying to sleep. you should see the wake reason in the system.log for me, I had to remove some _PRW name/methods from HDEF and GBE devices so it stays asleep. plus renamed EHC1 and EHC2 Link to comment Share on other sites More sharing options...
luky35 Posted August 31, 2015 Share Posted August 31, 2015 The icon is visible but I'd like to change default HD icon with El Capitan icon if it is possible. Link to comment Share on other sites More sharing options...
Allan Posted August 31, 2015 Share Posted August 31, 2015 Strange.... Well, the good news is that i understand you now. But the bad news is that i don't use El Capitan yet Link to comment Share on other sites More sharing options...
chris1111 Posted August 31, 2015 Share Posted August 31, 2015 The icon is visible but I'd like to change default HD icon with El Capitan icon if it is possible. http://mac-how-to.wonderhowto.com/how-to/change-your-mac-icons-0151545/ Link to comment Share on other sites More sharing options...
luky35 Posted September 1, 2015 Share Posted September 1, 2015 Thank you all, I succeeded. 2 Link to comment Share on other sites More sharing options...
T a D Posted September 2, 2015 Share Posted September 2, 2015 After a bit of a struggle El Capitan PB6 is up and running. It seems the Nvidia web driver added nvda_drv=1 to my nvram. This caused the first boot of El Capitan to reboot before getting to the post installation steps. Adding nv_disable=1 allowed the system to boot properly. FakeSMC, realtekALC (plus Clover_ALC patches from Toleda) and RealtekRTL8111 kexts all loaded via kext injection using Clover r3259. Nvidia web drivers installed and working. Sound working. Handoff working (via bluetooth, no wifi installed) - iMessages and FaceTime all working. Happy times! Link to comment Share on other sites More sharing options...
dodo Posted September 6, 2015 Share Posted September 6, 2015 I got every thing working but i try to update from the app store machine reboots and it reboot even from the recovery when i try to do fresh install. please advise. hardware (see sig) Thanks! Link to comment Share on other sites More sharing options...
gynekolog Posted September 9, 2015 Share Posted September 9, 2015 When I select Sleep it starts to turn off, but doesn't fully turn itself off. The graphics turn off but normally the blue LED on my computer will flash on and off when in sleeps. and the fans will turn off too. Same problem, sleep is not working. Link to comment Share on other sites More sharing options...
bkdwt Posted September 9, 2015 Share Posted September 9, 2015 RealtekRTL8111 kexts all loaded via kext injection using Clover r3259. Could you explain how you did it? Link to comment Share on other sites More sharing options...
TheTourist Posted September 10, 2015 Share Posted September 10, 2015 Hello! Trying to update to 10.11 GM. But can't boot into installer with error: OsxAptioFixDrv: Starting overrides for OS X Install Data\boot.efi OsxAptioFixDrv: Error - requested memory exceeds our allocated relocation block Requested mem: 5695000 - AAF8FFF, Pages: 5464, Size: 5464000 Reloc block: B355D000 - BC9A7FFF, Pages: 944B, Size: 944B000 I tried to boot in safe mode, without caches. No luck Also i tried to use another version of OsxAptioFixDrv from Clover installer Link to comment Share on other sites More sharing options...
velosirator Posted September 10, 2015 Share Posted September 10, 2015 FYI GM released....will report soon Link to comment Share on other sites More sharing options...
gynekolog Posted September 10, 2015 Share Posted September 10, 2015 ... But can't boot into installer with error: OsxAptioFixDrv: Starting overrides for OS X Install Data\boot.efi OsxAptioFixDrv: Error - requested memory exceeds our allocated relocation block ... Remove OsxAptioFixDrv and try OsxAptioFix2Drv. Link to comment Share on other sites More sharing options...
Recommended Posts