Matthew82 Posted June 28, 2015 Share Posted June 28, 2015 I have Asus R9 290x. In 10.11 dp2 work natively, without any patching. Link to comment Share on other sites More sharing options...
Pavo Posted June 28, 2015 Share Posted June 28, 2015 I have Asus R9 290x. In 10.11 dp2 work natively, without any patching. How many monitors? Link to comment Share on other sites More sharing options...
Matthew82 Posted June 28, 2015 Share Posted June 28, 2015 Two. One connected via Dual Link DVI-D and second to DVI. Hdmi working to, but only as single or dual monitor. Link to comment Share on other sites More sharing options...
jsl Posted June 28, 2015 Share Posted June 28, 2015 (edited) I have Asus R9 290x. In 10.11 dp2 work natively, without any patching. Glad to know that because I am using 10.11 DP2 too. Can you show me your config.plist if you boot by Clover or org.chameleon.Boot.plist if boot by Chameleon ? Because this Asus 290X worked natively in 10.10.4, however no such luck in 10.11 DP2 now. What really bothers me is in System Preference and About This Mac/Display there is HDMI display from AMD R9 290X card, but actually it shows blank screen in HDMI monitor. Hope it's not due to hardware problem in this card like over-heating, inadequate power supply, etc. Immediately reboot to 10.10.4 resumed everything is working again ! The first one shows working in 10.10.4. Anyone had the similar experience for AMD R9 290X card in 10.11 DP1 or DP2 ? Edited June 29, 2015 by jsl Link to comment Share on other sites More sharing options...
Pavo Posted June 29, 2015 Share Posted June 29, 2015 Well I'm glad some 290X are working fine without patching, because the Sapphire 290X 8Gb requires a Framebuffer and connector patch for it to work with multi monitors Link to comment Share on other sites More sharing options...
luxinhaus Posted June 29, 2015 Share Posted June 29, 2015 I have Asus R9 290x. In 10.11 dp2 work natively, without any patching. True Link to comment Share on other sites More sharing options...
BNZfive Posted June 29, 2015 Share Posted June 29, 2015 Glad to know that because I am using 10.11 DP2 too. Can you show me your config.plist if you boot by Clover or org.chameleon.Boot.plist if boot by Chameleon ? Because this Asus 290X worked natively in 10.10.4, however no such luck in 10.11 DP2 now. What really bothers me is in System Preference and About This Mac/Display there is HDMI display from AMD R9 290X card, but actually it shows blank screen in HDMI monitor. Hope it's not due to hardware problem in this card like over-heating, inadequate power supply, etc. Immediately reboot to 10.10.4 resumed everything is working again ! Anyone had the similar experience for AMD R9 290X card in 10.11 DP1 or DP2 ? your 30-bit color is confusing. It says ARGB (Alpha Red Green Blue) 2101010 (2 10 10 10) that equals 32, not 30. Plus, if it's 30 then you have no Alpha channel (no transparency) and if it's 32, you only have a 2-bit alpha channel. Odd 1 Link to comment Share on other sites More sharing options...
jsl Posted June 29, 2015 Share Posted June 29, 2015 (edited) your 30-bit color is confusing. It says ARGB (Alpha Red Green Blue) 2101010 (2 10 10 10) that equals 32, not 30. Plus, if it's 30 then you have no Alpha channel (no transparency) and if it's 32, you only have a 2-bit alpha channel. Odd Thanks for your comment. The working one in 10.10.4 was attached here: Got some progress now after booting with GraphicsEnable=N and disable Intel HD4600 in BIOS Almost normal display from 290X now but still suffered from 30-bitARGB(2101010) instead of 32-bitARGB(8888) in 10.10.4. If I reduced screen resolution from 2560x1440x32 (HDMI 2.0) to 1920x1080x32, it will show normal 32-bitARGB(8888) in 10.11 DP2. Edited July 3, 2015 by jsl Link to comment Share on other sites More sharing options...
Matthew82 Posted June 29, 2015 Share Posted June 29, 2015 Glad to know that because I am using 10.11 DP2 too. Can you show me your config.plist if you boot by Clover or org.chameleon.Boot.plist if boot by Chameleon ? Because this Asus 290X worked natively in 10.10.4, however no such luck in 10.11 DP2 now. What really bothers me is in System Preference and About This Mac/Display there is HDMI display from AMD R9 290X card, but actually it shows blank screen in HDMI monitor. Hope it's not due to hardware problem in this card like over-heating, inadequate power supply, etc. Immediately reboot to 10.10.4 resumed everything is working again ! The first one shows working in 10.10.4. Anyone had the similar experience for AMD R9 290X card in 10.11 DP1 or DP2 ? Sorry for my English. I have bad news. Dual monitors working randomly. I don't know why. This time i can't run HDMI display, only 2 monitors via DVI. But single monitor work always. Im using Clover Link to comment Share on other sites More sharing options...
jsl Posted June 29, 2015 Share Posted June 29, 2015 Sorry for my English. I have bad news. Dual monitors working randomly. I don't know why. This time i can't run HDMI display, only 2 monitors via DVI. But single monitor work always.Zrzut ekranu 2015-06-29 o 10.55.27.pngZrzut ekranu 2015-06-29 o 10.54.07.pngZrzut ekranu 2015-06-29 o 10.54.55.png Im using Clover Boot by Clover I can get Intel HD4600 (DP display with DP audio) and AMD R9 290X (triple display by HDMI, DVI & DP ) at the same time. Link to comment Share on other sites More sharing options...
Matthew82 Posted June 29, 2015 Share Posted June 29, 2015 Boot by Clover I can get Intel HD4600 (DP display with DP audio) and AMD R9 290X (HDMI display & DVI display) at the same time. When i set as primary card 29 280x workin everything as you say (HDMI display & DVI display). But when 290x is primary or single working one of those ports. Link to comment Share on other sites More sharing options...
jsl Posted June 29, 2015 Share Posted June 29, 2015 (edited) When i set as primary card 29 280x workin everything as you say (HDMI display & DVI display). But when 290x is primary or single working one of those ports. My primary display is Intel HD4600 and AMD 290X is the secondary display. Boot by Clover I can get 4 monitors at the same time while 3 from AMD 290X shown in my post #210 here. If boot by Chameleon I can get only 2 monitors at the same time that means only one HDMI dispaly from AMD 290X and the other one from Intel HD4600. Edited June 29, 2015 by jsl Link to comment Share on other sites More sharing options...
htebmal Posted June 29, 2015 Share Posted June 29, 2015 All working on HP Probook 450 G2; anyone else having trouble with sleep though? I'm sure I'm just forgetting a step but wondered if they Apple with things a bit... EDIT: to clarify, No changes to system as shipped except SSD/AR9280; using clover and PBI. System Power Settings: AC Power: System Sleep Timer (Minutes): 0 Disk Sleep Timer (Minutes): 0 Display Sleep Timer (Minutes): 0 Wake on LAN: No AutoPowerOff Delay: 14400 AutoPowerOff Enabled: 1 Current Power Source: Yes DarkWakeBackgroundTasks: 0 Display Sleep Uses Dim: Yes Hibernate Mode: 0 PrioritizeNetworkReachabilityOverSleep: 0 Standby Delay: 10800 Standby Enabled: 1 Battery Power: System Sleep Timer (Minutes): 0 Disk Sleep Timer (Minutes): 0 Display Sleep Timer (Minutes): 0 AutoPowerOff Delay: 14400 AutoPowerOff Enabled: 1 DarkWakeBackgroundTasks: 0 Display Sleep Uses Dim: Yes Hibernate Mode: 0 Reduce Brightness: Yes Standby Delay: 10800 Standby Enabled: 1 Link to comment Share on other sites More sharing options...
Matthew82 Posted June 29, 2015 Share Posted June 29, 2015 My primary display is Intel HD4600 and AMD 290X is the secondary display. Boot by Clover I can get 4 monitors at the same time while 3 from AMD 290X shown in my post #210 here. If boot by Chameleon I can get only 2 monitors at the same time that means only one HDMI dispaly from AMD 290X and the other one from Intel HD4600. But when 280x is primary the performance of 290x is worse and GPUs is more heat. Whet 290x is primary everything is faster, cooler, and quieter (y) Link to comment Share on other sites More sharing options...
iEric Posted June 29, 2015 Share Posted June 29, 2015 Hey, I'm new in the forum sorry if i'm asking a stupid question but, Has anyone succeded on booting OS X El Capitan DP1 with an Intel HD Graphics 4000? I'm having this problem since Yosemite although everything works fine using Chameleon with GraphicsEnabler=Yes, but never seemed to work properly with Clover, the screen goes black when it boots. I've never used Clover before, but I suppose Intel HD Graphics 4000 should be natively supported by OS X, and i've never had a problem using it with Chameleon. I'm using a simple laptop with an i3 3217U Ivy Brigde chipset. Also, is Chameleon booting El Capitan yet? Link to comment Share on other sites More sharing options...
PHV Posted June 29, 2015 Share Posted June 29, 2015 My attempt to install El Capitan failed on the Clover side. What should I click in the Clover installer or this rig: Asus P5Q Deluxe Intel Q6600 Nvidia GTX 275 SATA HDD Link to comment Share on other sites More sharing options...
jsl Posted June 30, 2015 Share Posted June 30, 2015 (edited) But when 280x is primary the performance of 290x is worse and GPUs is more heat. Whet 290x is primary everything is faster, cooler, and quieter (y) In my Asus Z87 Deluxe/Dual MB : When 290X is the primary and only display the test score in LuxMark is about 1% higher (3001 vs. 2966) than 290X is the secondary display. I would say there is no significant difference for OpenCL performance by LuxMark 2.1. Regarding OpenGL bench test by CineBench R15 the difference was increased (117.14 fps vs. 110.34 fps) to 5~6 %. Hey, I'm new in the forum sorry if i'm asking a stupid question but, Has anyone succeded on booting OS X El Capitan DP1 with an Intel HD Graphics 4000? I'm having this problem since Yosemite although everything works fine using Chameleon with GraphicsEnabler=Yes, but never seemed to work properly with Clover, the screen goes black when it boots. I've never used Clover before, but I suppose Intel HD Graphics 4000 should be natively supported by OS X, and i've never had a problem using it with Chameleon. I'm using a simple laptop with an i3 3217U Ivy Brigde chipset. Also, is Chameleon booting El Capitan yet? 1. El Capitan 10.11 DP1/DP2 can be booted by Chameleon (Enoch v.2725) at http://www.insanelymac.com/forum/files/file/71-enoch/ 2. Both Clover and Chameleon need correct DSDT.aml in which support Intel HD 4000 & patched AppleHDA.kext. in Asus Z77 with Intel HD4000 both methods are working for me. 3. Rollback to 10.10.3's AppleIntelFramebufferCapri.kext and AppleHDA.kext are required in my Asus Z77 MB. Edited June 30, 2015 by jsl Link to comment Share on other sites More sharing options...
PHV Posted June 30, 2015 Share Posted June 30, 2015 Duuudes please help. Link to comment Share on other sites More sharing options...
Bruxo Posted June 30, 2015 Share Posted June 30, 2015 I'm sick enough !! It is the 4th installation and whenever it happens !!! Link to comment Share on other sites More sharing options...
jsl Posted July 1, 2015 Share Posted July 1, 2015 My attempt to install El Capitan failed on the Clover side. What should I click in the Clover installer or this rig: Asus P5Q Deluxe Intel Q6600 Nvidia GTX 275 SATA HDD Please try my config.plist. Replaced P5Q01.aml by your DSDT.aml for fully compatibility. I'm sick enough !! It is the 4th installation and whenever it happens !!! If you really want to get help here, please translate this alert in English ! config.plist.zip Link to comment Share on other sites More sharing options...
Allan Posted July 1, 2015 Share Posted July 1, 2015 If you really want to get help here, please translate this alert in English ! @Bruxo, maybe your HDD is in end of life. You can try check and repair the system preferences via Penboot. And do a check with another software for make sure, if the problem really are your HDD. Link to comment Share on other sites More sharing options...
mendietinha Posted July 1, 2015 Share Posted July 1, 2015 i have random KP when booting. from applesmartbattery, to acpi... totally random. most of times boots in the first attempt. sometimes not. anyone else having those random KP when booting? Link to comment Share on other sites More sharing options...
jsl Posted July 2, 2015 Share Posted July 2, 2015 In Asus Z77 MB with Intel HD 4000 & Nvidia GTX780: Need replaced by 10.10.3's AppleIntelFramebufferCapri.kext (10.6.20) & patched AppleHDA.kext (267.0) from Mirone (http://www.insanelymac.com/forum/topic/298663-applehda-for-yosemite/) Then both Intel HD4000 and GTX 780 (including HDMI audio) display and ALC-898 sound are working now. Both bootloader (Chameleon & Clover) booted successfully. Thanks for those contributed here ! Recently I found a better way to install 10.11DP1 or DP2 in Asus Z77 MB with Intel HD4000 & Nvidia GTX 780: At first disable Intel HD4000 display in BIOS then boot by Chameleon with display by Nvidia GTX780 patching AppleHDA.kext by Toleda's command 110_v1.0c reboot after enabled Intel HD4000 in BIOS then everything for ALC-898 and HDMI audios from Intel HD4000 & GTX 780 are working now. No need to rollback of AppleHDA or AppleIntelFramebufferCapri ! This method also worked for upgrade from 10.10.3 to 10.10.4 ! Link to comment Share on other sites More sharing options...
falanx Posted July 2, 2015 Share Posted July 2, 2015 Hey, I'm new in the forum sorry if i'm asking a stupid question but, Has anyone succeded on booting OS X El Capitan DP1 with an Intel HD Graphics 4000? I'm having this problem since Yosemite although everything works fine using Chameleon with GraphicsEnabler=Yes, but never seemed to work properly with Clover, the screen goes black when it boots. I've never used Clover before, but I suppose Intel HD Graphics 4000 should be natively supported by OS X, and i've never had a problem using it with Chameleon. I'm using a simple laptop with an i3 3217U Ivy Brigde chipset. Also, is Chameleon booting El Capitan yet? Post your config.plist. I'd like to see it because I have the same CPU and GPU and for sure I had almost to none problems with it. Link to comment Share on other sites More sharing options...
Bruxo Posted July 2, 2015 Share Posted July 2, 2015 @Bruxo, maybe your HDD is in end of life. You can try check and repair the system preferences via Penboot. And do a check with another software for make sure, if the problem really are your HDD. HD is good working perfectly with Yosemite but when installing El Captan he always is malfunctioning after system reboot If foce the Pentium processor Haswell then give KP I do not know what the defect after installation, it always happens indefinitely what the HD partitions or other drives Link to comment Share on other sites More sharing options...
Recommended Posts