pepto Posted November 22, 2013 Author Share Posted November 22, 2013 The clover install works right now only not for my 4k 500GB HDD so now i am using chameleon but when clover works with my 4K HDD i will switch to clover. If the recovery works i have to test it, but i need it for find my mac. Link to comment Share on other sites More sharing options...
lukin Posted November 22, 2013 Share Posted November 22, 2013 The clover install works right now only not for my 4k 500GB HDD so now i am using chameleon but when clover works with my 4K HDD i will switch to clover. If the recovery works i have to test it, but i need it for find my mac. What about Wake/Sleep using my DSDT?, Do you have an install guide using Clover, I`d like to try (so sorry can`t wait until you figure out 4K HDD issue...) Thx so much!... Link to comment Share on other sites More sharing options...
pepto Posted November 22, 2013 Author Share Posted November 22, 2013 Clover is just a bootloader like chameleon only you must configure your config.plist with the clover configurator thats all. First install osx on your HDD after that install clover on you HDD just like chameleon.During installation clover choose customise boot loader - install boot0af in MBR and install it, then with the clover configurator create your config.plist for dell thats it. Or use the config.plist in this post. Link to comment Share on other sites More sharing options...
lukin Posted November 22, 2013 Share Posted November 22, 2013 I don`t see any "config.plist" anywhere, can you attach it please so I can have a look?, almost forgot..again, i have to insist, sorry!, What about Wake/Sleep using my DSDT? Thx! Link to comment Share on other sites More sharing options...
lalakobe Posted November 22, 2013 Share Posted November 22, 2013 sleep/wake wth your DSDT is working flawlessly had to add <key>DSDT</key> <string>/Extra/DSDT.aml</string> to my org.chameleon.boot.plist everything works with only 5 extra kexts: voodoohda - sound appleintele1000e - lan eliottforcelegacyrtc - no bios reset fakesmc - kernel panic nullcpupowermanagement - kernel panic now boots without -f switch - speeding up boot process significantly overall performance seems higher than without dsdt Link to comment Share on other sites More sharing options...
lukin Posted November 22, 2013 Share Posted November 22, 2013 sleep/wake wth your DSDT is working flawlessly had to add <key>DSDT</key> <string>/Extra/DSDT.aml</string> to my org.chameleon.boot.plist everything works with only 5 extra kexts: voodoohda - sound appleintele1000e - lan eliottforcelegacyrtc - no bios reset fakesmc - kernel panic nullcpupowermanagement - kernel panic now boots without -f switch - speeding up boot process significantly overall performance seems higher than without dsdt Thx so much for reporting back, I know my DSDT works fine with Chameleon, I was referring to Pepto`s install using Clover. Link to comment Share on other sites More sharing options...
ernani Posted November 22, 2013 Share Posted November 22, 2013 Thank you all very much for your support! After an extremely hectic week, with lots of formatting and system installations (a couple of systems at work started to malfunction at the same time), I found some time and gave another shot on Mavericks for my Dell 780. Everything works flawlessly!!! Audio, Graphics (I purchased a HD 5450 Sapphire), Network, AppStore updates and Sleep / Wake, thanks to lukin's DSDT and instructions at post #68 (thanks man ). My only problem is that when my system wakes from sleep, ethernet doesn't wake up as well. No matter what I do, network is gone. I'm using AppelIntelE1000e.kext from Pepto's original post. Any idea how to correct it? Link to comment Share on other sites More sharing options...
lalakobe Posted November 22, 2013 Share Posted November 22, 2013 My only problem is that when my system wakes from sleep, ethernet doesn't wake up as well. No matter what I do, network is gone. I'm using AppelIntelE1000e.kext from Pepto's original post. Any idea how to correct it? thats strange - i use the same kext and my lan is working after sleep/wake. maybe you do not have "EthernetBuiltIn=Yes" string in your config? also you can try intel lan kext from post #30 i was able to boot without nullcpupowermanagement kext, so now i am using only 4 non-original: voodoohda - sound appleintele1000e - lan eliottforcelegacyrtc - no bios reset fakesmc - kernel panic, sleep etc Link to comment Share on other sites More sharing options...
ernani Posted November 22, 2013 Share Posted November 22, 2013 I'll try the Intel kext as well. It seems though that a lot of people are facing this problem. In the hackintosh community I read that it manifests itself when the PC is connected to a gigabit switch (my case as well). But I found a lot of complaints from iMac and Macbook users. I'll have to try and see. FYI, the network I am accessing is not connected to the internet (office lan), and I'm connected with a static IP. Even ping is not working... Link to comment Share on other sites More sharing options...
lukin Posted November 22, 2013 Share Posted November 22, 2013 I'll try the Intel kext as well. It seems though that a lot of people are facing this problem. In the hackintosh community I read that it manifests itself when the PC is connected to a gigabit switch (my case as well). But I found a lot of complaints from iMac and Macbook users. I'll have to try and see. FYI, the network I am accessing is not connected to the internet (office lan), and I'm connected with a static IP. Even ping is not working... I`m glad it went well this time around, put it to good use now ...our beast is a robust machine, don`t just take my word for it, can`t even remember last time i rebooted or shut it down (if i don`t really have to)...whenever i get tired of it, i just put it to sleep...and then with a click of a button, it`s there waiting for more tinkering...that`s how stable it is... I had that ethernet problem, fixed it with "Intel82566MM.kext" (#post30). Link to comment Share on other sites More sharing options...
pepto Posted November 23, 2013 Author Share Posted November 23, 2013 He Lukin sorry i was forgot to attach the config.plist but here he is. Greetz pepto config.plist.zip 1 Link to comment Share on other sites More sharing options...
ernani Posted November 23, 2013 Share Posted November 23, 2013 I`m glad it went well this time around, put it to good use now ...our beast is a robust machine, don`t just take my word for it, can`t even remember last time i rebooted or shut it down (if i don`t really have to)...whenever i get tired of it, i just put it to sleep...and then with a click of a button, it`s there waiting for more tinkering...that`s how stable it is... I had that ethernet problem, fixed it with "Intel82566MM.kext" (#post30). Tried it myself today. Works like a charm! If only I could find a driver for a rather old Panasonic Workio MFP we have at the office, which is our main printer, I would completely format my Windows installation . But you're right. It boots in seconds (under a minute), and it shuts down / sleeps almost instantly! The Windows 7 installation I was talking about, although quite fresh (I have it a couple of days), and with the most basic programs we need at the office, just takes ages to become responsive after booting / waking up... 1 Link to comment Share on other sites More sharing options...
morpheousman Posted November 27, 2013 Share Posted November 27, 2013 A DSDT Edit for the Radeon 5450 would prevent the need to reinstall edited kexts after an update. This is not within my skill set at the moment. http://www.insanelymac.com/forum/topic/293049-guide-mavericks-amd-radeon-hd5450 Link to comment Share on other sites More sharing options...
Guest Posted November 29, 2013 Share Posted November 29, 2013 My 780 is not booting to the setup but only to the installation options. Any idea what could be the solution? Link to comment Share on other sites More sharing options...
morpheousman Posted November 29, 2013 Share Posted November 29, 2013 My 780 is not booting to the setup but only to the installation options. Any idea what could be the solution? Make sure that after you do the the installation process and reboot, you choose to boot into your Mac installation on your Hard Drive, not back into your USB drive. Link to comment Share on other sites More sharing options...
Guest Posted November 29, 2013 Share Posted November 29, 2013 Make sure that after you do the the installation process and reboot, you choose to boot into your Mac installation on your Hard Drive, not back into your USB drive. Thank you. That brought me to the idea to push Enter during bootup. In the guide this is optional but it seems to mandatory to get the boot option list. Thanks again. Link to comment Share on other sites More sharing options...
morpheousman Posted November 29, 2013 Share Posted November 29, 2013 Thank you. That brought me to the idea to push Enter during bootup. In the guide this is optional but it seems to mandatory to get the boot option list. Thanks again. The Guide needs to be tweaked a little. Happy to help! Link to comment Share on other sites More sharing options...
Dunnowhat Posted December 15, 2013 Share Posted December 15, 2013 I didn't seem to be able to install on mbr using this guide. I tried to replace some other versions of OSInstall but no juice. I noticed all other OSInstalls are for OSX 13A603 version, but somehow mine is 13A602. Will that make any differences? 1 Link to comment Share on other sites More sharing options...
Guest Posted December 17, 2013 Share Posted December 17, 2013 Just FYI. I did an App Store update from 10.9 to 10.9.1 and had no problems at all. Everything seems to be working as normal. Link to comment Share on other sites More sharing options...
morpheousman Posted December 18, 2013 Share Posted December 18, 2013 Just FYI. I did an App Store update from 10.9 to 10.9.1 and had no problems at all. Everything seems to be working as normal. Thanks for the info. I just took the update as well, and I see no problems. (knock on wood). 1 Link to comment Share on other sites More sharing options...
ernani Posted December 20, 2013 Share Posted December 20, 2013 Yup! I updated too. Everything is working just fine Link to comment Share on other sites More sharing options...
Dunnowhat Posted December 22, 2013 Share Posted December 22, 2013 Does any of you have trouble with ethernet being disabled after wake from sleep? Has anybody solve that problem yet? yes I tried post #30. btw my specs is optiplex 760. Thanks Link to comment Share on other sites More sharing options...
Grim Reaper Posted December 23, 2013 Share Posted December 23, 2013 Install the Ethernet kext from post #30, make sure you remove the IntelE1000.kext, and fix permissions 10.9.1 update works perfectly, no reinstalls required. 1 Link to comment Share on other sites More sharing options...
osanda Posted December 25, 2013 Share Posted December 25, 2013 I`ve already uploaded all the kexts that I`m using right now....except maybe for those that come with myhack (which I used to create my installer)...anyway here goes; AppleACPIPlatform.kext-------->>> without it, my system won`t boot! AppleHDADisabler.kext--------->>> sound fix works with VoodooHDA VoodooHDA.kext---------------->>> sound fix AppleLPC.kext------------------->>> edited infoplist to avoid dsdt hack FakeSMC.kext------------------->>> Mandatory but also used for smbios and powernap IOPlatformPluginFamily.kext---->>> PowerNap fix Intel82566MM.kext-------------->>> Ethernet fix lspcidrv.kext---------------------->>> Myhack Patched_10.7_AppleRTC.kext-->>> Myhack Thanks for this, days of frustration ended right here 2 Link to comment Share on other sites More sharing options...
horiarave Posted January 10, 2014 Share Posted January 10, 2014 Hello everybody, just want to say thanks for this great tutorial, I have the same config as Pepto, Dell780/Saphire HD5450 1Gb. After the install I couldn't get the VGA to work with just the settings provided in the tutorial, after modifying the video kexts I had to add the below to org.chameleon.Boot.plist witch got the VGA to work perfectly, full resolution and QE/CI: <key>AtiConfig</key> <string>Eulemur</string> Another issue I had was the volume, it didn't work when moving the slider, which I fixed by installing the attached kext. Also, I created the install disk with MyHack, using Mavericks 10.9 downloaded from AppStore and I also updated to 10.9.1 from AppStore with no issues. I have 2 issues that I can't fix and I hope you can help me: I fixed the Sleep/Wake problem with the DSDT provided in this thread but when the computer comes back from sleep my ethernet doesn't work anymore and I have to restart to get it to work. I installed the Intel82566MM.kext but didn't fix my problem, I have the ethernet built in set to yes. Another thing that doesn't work for me is iMessage, can't login, I receive a message "Your Apple ID can't be used to set up iMessage at this time" when trying to login, I installed the FileNVRAM, reset the network profile, put my network on top of the list in network preferences, reset my Apple ID password, entered the ethernet hex to org.chameleon.Boot.plist etc but nothing worked, still get the same message, my account is working on my macbook and iPhone so the problem is not the account itself. My iCloud and AppStore are working. Happy New Year for everybody, cause this is the first post in 2014 , and hope you can help me with my issues. VoodooHDA.kext.zip Link to comment Share on other sites More sharing options...
Recommended Posts