Jump to content

Ozmosis

xpamamadeus

By xpamamadeus,
in Ozmosis

 Share
6,231 posts in this topic

Recommended Posts

davidm71
davidm71
Posted
Posted

Sorry for the sarcasm. I'm just going to take it back to formula. Start over with a fresh bios file and fresh OZ files. So far I've tried deleting dsdt and kext files in the efi and resetting nvram. Though I'm not completely clueless. I like having a challenge and I'll solve with or without help. Thanks.

 

Edit: After starting over from scratch I had a little luck getting hermitshell working but it was only after a cmos reset and it was random at best.

Link to comment
Share on other sites
alecwild
alecwild
Posted
Posted

Please help! I installed AHCI_Intel_Generic_SATA.kext in EFI/Oz/Darwin/Common/Extensions and suddenly my system will not start - just a black screen. I can't start in Safe Mode or Single User mode. Can't start from El Cap install USB. I can get to Bios settings or EDK shell, but that's it. My EFI volume was disk4s1 when I mounted it from Terminal in OSX.

 

Can I delete that kext from the EDK shell? What can I do?

 

El Cap 10.11.4 Oz 167-Mass F6, GA-Z97xUD7TH, EVGA 960 x2 graphics.

Link to comment
Share on other sites
MacUser2525
MacUser2525
Posted
Posted

I e been using Oz since 894, this is the first time I've run into this kind of problem. Now I cannot get into EDK shell - Gigabyte logo then black screen. I'd appreciate any advice you can give, as I'm trying to become a more advanced user.

 

Firstly never test anything on a machine that is important to you only a testing machine.  If no spare machine then only on a testing drive you boot from. For your problem here remove the drive plug in a machine that has either windows or linux on it so you can access the fat32 formatted EFI partition that is on the disk then delete the offending .kext you installed.

Link to comment
Share on other sites
ammoune78
ammoune78
Posted
Posted

Please help! I installed AHCI_Intel_Generic_SATA.kext in EFI/Oz/Darwin/Common/Extensions and suddenly my system will not start - just a black screen. I can't start in Safe Mode or Single User mode. Can't start from El Cap install USB. I can get to Bios settings or EDK shell, but that's it. My EFI volume was disk4s1 when I mounted it from Terminal in OSX.

 

Can I delete that kext from the EDK shell? What can I do?

 

El Cap 10.11.4 Oz 167-Mass F6, GA-Z97xUD7TH, EVGA 960 x2 graphics.

 

Use your windows to delete it!

Boot into windows, open diskpart and type list disk and select OS X disk, type list partition and select your efi partition, type assign letter D.

Now go to windows task manager select new task and go to refi partition from it and select your kext if it not appear select all files. 

Link to comment
Share on other sites
stehor
stehor
Posted
Posted

@davidm71 ready to flash has smbios iMac14,2  OzDefaults.plist will need to disable sip via recovery. 


fakesmc is current and has agdp fix in config2 aka none and AmdBaffinGraphicsAccelrator for amd rx cards

Z87XUD5H.F9.zip

FakeSMCCompress.ffs.zip

  • Like 1
Link to comment
Share on other sites
davidm71
davidm71
Posted
Posted

@davidm71 ready to flash has smbios iMac14,2  OzDefaults.plist will need to disable sip via recovery. 

fakesmc is current and has agdp fix in config2 aka none and AmdBaffinGraphicsAccelrator for amd rx cards

 

 

OMG!! Thank you! I won't be able to test these out until next week but can't wait!

 

Wheres that rep button! 

 

BTW: I don't have AMD card just nvidia. Thanks.

Link to comment
Share on other sites
Kynyo
Kynyo
Posted
Posted

Try this: 

<key>AAPL,ig-platform-id</key>
<integer>170262534</integer>
 

!! WARNING DisableIntelInjection needs to be set to false to function !!

 

Here its a list of framebuffers used in conjuction with ozmosis:

 

0 =04060000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, Mobile GT1 =67502080

1 = 0c060000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, SDV Mobile GT1 =201719808
2 =04160000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, Mobile GT2 =68550656
3 = 0a160000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, ULT Mobile GT2 =169213952
4 = 0c160000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, SDV Mobile GT2 =202768384
5 = 04260000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, Mobile GT3 =69599232
6 = 0a260000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, ULT Mobile GT3 =170262528
7 = 0c260000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, SDV Mobile GT3 =203816960
8 = 0d260000 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, CRW Mobile GT3 =220594176
9 = 04160002 = 64MB, Pipes: 1, Ports: 1, FBMem: 1, Mobile GT2 =68550658
10 = 0d220003 = 0MB, Pipes: 0, Ports: 0, FBMem: 0, CRW Desktop GT3 =220332035
11 = 0a260005 = 32MB, Pipes: 3, Ports: 3, FBMem: 3, ULT Mobile GT3 =170262533
12 = 0a260006 = 32MB, Pipes: 3, Ports: 3, FBMem: 3, ULT Mobile GT3 =170262534
13 = 0a260006 = 64MB, Pipes: 3, Ports: 4, FBMem: 3, CRW Mobile GT3 =170262534
14 = 0a260007 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, ULT Mobile GT3 =170262535
15 = 0a2e0008 = 64MB, Pipes: 3, Ports: 3, FBMem: 3, ULT Reserved GT3 =170786824

  • Like 1
Link to comment
Share on other sites
davidm71
davidm71
Posted
Posted

Well almost about to give up. My Sierra partition fails to load stopping or rebooting at motherboard LED error code 'Ad' where as

El Capitan continues to 'A0'.  Its got to be a bios setting conflicting?

Link to comment
Share on other sites
mhaeuser
mhaeuser
Posted
Posted

Sorry if I did not understand if it was a pun or is serious. Because I found nothing about OpenCore.

 

http://www.insanelymac.com/forum/topic/285920-new-os-x-compatible-motherboard-quo/page-153?do=findComment&comment=2302024

 

Hi 

Can any one help me to inject Device id for HD 4400 to attached DSDT.aml?? I need to enable internal HD4400 graphics.

Device Id = 0x0412

https://mega.nz/#!BslAnDZL!LwBXxK0CUx88n6hZlQ5Cj_qozawxvxcwUC5X-WirQvM

 

Thank you

 

This is the Ozmosis thread, not the "DSDT patch request thread"...

 

Well almost about to give up. My Sierra partition fails to load stopping or rebooting at motherboard LED error code 'Ad' where as

El Capitan continues to 'A0'.  Its got to be a bios setting conflicting?

 

Check what these codes mean. There should be a section in your manual, or a list on your board vendor's website.

Check if the motherboard LED code actually changes between boot menu and pre-reboot, it might be, it's only telling you it booted a bootloader/exited Boot Services.

Link to comment
Share on other sites
LAbyOne
LAbyOne
Posted
Posted

Hi 

Can any one help me to inject Device id for HD 4400 to attached DSDT.aml?? I need to enable internal HD4400 graphics.

Device Id = 0x0412

https://mega.nz/#!BslAnDZL!LwBXxK0CUx88n6hZlQ5Cj_qozawxvxcwUC5X-WirQvM

 

Thank you

 

knowing your HW would help better anyway 

this one worked f0r me

# Insert method _DSM into device with _ADR 0x00020000
#
into method label _DSM parent_adr 0x00020000 remove_entry;
into device name_adr 0x00020000 insert
begin
Method (_DSM, 4, NotSerialized)  // _DSM: Device-Specific Method\n
                    {\n
                        If (LEqual (Arg2, Zero))\n
                        {\n
                            Return (Buffer ()\n
                            {\n
                                 0x03                                             /* . */\n
                            })\n
                        }\n

                        Return (Package ()\n
                        {\n
                            "AAPL,snb-platform-id", \n
                            Buffer ()\n
                            {\n
                                 0x12, 0x04, 0x00, 0x00                           /* .... */\n
                            }, \n

                            "AAPL,ig-platform-id", \n
                            Buffer ()\n
                            {\n
                                 0x03, 0x00, 0x22, 0x0d                           /* ..f. */\n
                            }, \n

                            "hda-gfx", \n
                            Buffer ()\n
                            {\n
                                "onboard-1"\n
                            }, \n

                            "model", \n
                            Buffer ()\n
                            {\n
                                "Intel HD 4400"\n
                            }\n
                        })\n
                    }\n
end

hope it helps

to use it copy/paste + save as .txt  file to use with maciasl

Link to comment
Share on other sites
MattsCreative
MattsCreative
Posted
Posted

https://drive.google.com/drive/folders/0B3y5hldpEFDYeWczaTNCNXd1VjQ?usp=sharinghey been a long time crusher if you see this can you make me a oz bios for with the bios ilinked please with the hd4600 ig platform id and imac 15,1 smbios add what you want into the rom thanks man 

Link to comment
Share on other sites
davidm71
davidm71
Posted
Posted

 

 

Check what these codes mean. There should be a section in your manual, or a list on your board vendor's website.

Check if the motherboard LED code actually changes between boot menu and pre-reboot, it might be, it's only telling you it booted a bootloader/exited Boot Services.

 

Well I looked up that LED post code and it says "issue Ready To Boot event for OS Boot" which means the system is ready to load the OS I suppose. Whats weird about this complete stall out on the Apple logo without progress bar is that I can still load El Cap 11.3 and even weirder is that on the stock bios Clover is also having an issue loading the sierra installer or that partition for that matter. So I don't think its my Ozmosis bios at fault but some conflict with hardware. Wonder what that could be..

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...