Jump to content

Ozmosis

xpamamadeus

By xpamamadeus,
in Ozmosis

 Share
6,231 posts in this topic

Recommended Posts

truemac
truemac
Posted
Posted

 

Nothing, every trying to load my dsdt are failed  :wallbash:  and i don't know why.

02:274 00:000 Base Directory Path :\Efi\Quo\:
02:278 00:004 Local Path          :\Efi\Quo\Darwin\:
02:278 00:000 Common Kexts Path   :\Efi\Quo\Darwin\Extensions\:
02:278 00:000 ACPI Dump Path      :\Efi\Quo\Acpi\Dump:
02:278 00:000 ACPI Load Path      :\Efi\Quo\Acpi\Load:
02:278 00:000 Found Defaults 99F2839C-57C3-411E-ABC3-ADE5267D960D from Fv
02:282 00:004 Acpi Loader Mode 0x004D (Enabled  | Darwin | Windows | Update Legacy)
02:294 00:011 Boot0001 "Mavericks" Already exists.
02:302 00:007 Boot0002 "Recovery HD" Already exists.
02:592 00:289 BootOrder 01 02 03 04 (4)

this a piece of boot code get it with dpcimanager

 

Delete EFI folder restart then mount EFI partition then put your DSDT again in EFI/Quo/ACPI/Load.

if this don't work you make a mistake in the Bios.

i also had the problem.

good luck ^_^

Link to comment
Share on other sites
Aigors
Aigors
Posted
Posted

The bootlog with dpcimanager 

00:000 00:000 Ozmosis 1.01.0894 RELEASE (2013-12-09 21:54:35 VS2013x86) on 2014-04-11 22:11:27
00:000 00:000 Found Firmware UEFI Spec  :2.31:
00:000 00:000 Found Firmware Vendor     :American Megatrends:
00:000 00:000 Found Firmware Revision   :4.653:
00:000 00:000 Detected Aptio 2.x firmware enabling fixes
00:000 00:000 Embedded Mode Detected
02:126 02:126 BootOrder 01 02 03 (3)
02:128 00:001 Found Boot0001 "Mavericks" (0x14)
02:128 00:000 Found Boot0002 "Recovery HD" (0x18)
02:128 00:000 Found Boot0003 "UEFI: C300-CTFDDAC128MAG" (0x32)
02:229 00:101 Found Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz (3A.06.00) Cores 4 Threads 4
02:229 00:000  BusRatio 16 / 34 (36)
02:229 00:000  P-State Coordination Type HW_ALL -> SW_ANY = SW_ANY
02:229 00:000  Disabling Invalid Flex-Ratio F0000 -> E0000 = E0000
02:229 00:000  TurboBusRatio1 38 -> 38 = 38
02:229 00:000  TurboBusRatio2 38 -> 37 = 38
02:229 00:000  TurboBusRatio3 37 -> 36 = 37
02:229 00:000  TurboBusRatio4 36 -> 35 = 36
02:229 00:000 Calculated TSC Frequency 3403MHz (3403347020)
02:229 00:000 Calculated CPU Frequency 3403MHz (3403346994)
02:229 00:000 Calculated FSB Frequency  100MHz (100098441)
02:229 00:000 Found Intel Graphics Controller [8086:0162] [1458:D000] rev 9
02:229 00:000 Found <null string> Lan Controller [1969:1083] [1458:E000] rev 192 00:00:00:00:00:00
02:229 00:000 Found 7 Series SMBUS Controller [8086:1E22] MMIO 0xDFD15000, IOPort 0xF040
02:253 00:024  Slot 1 4096MB DDR3 SDRAM 1333MHz "Kingston" "9905474-060.A00LF" "9C2FFC69"
02:278 00:024  Slot 3 4096MB DDR3 SDRAM 1333MHz "Kingston" "9905474-060.A00LF" "A02F3A69"
02:284 00:006 Found Storage PciRoot(0x0)/Pci(0x1F,0x2)/Sata(0x0,0xFFFF,0x0)/HD(1,GPT,C73033FC-EB78-4A31-AB10-6340160E3B97,0x28,0x64000)
02:284 00:000 Base Directory Path :\Efi\Quo\:
02:289 00:004 Local Path          :\Efi\Quo\Darwin\:
02:289 00:000 Common Kexts Path   :\Efi\Quo\Darwin\Extensions\:
02:289 00:000 ACPI Dump Path      :\Efi\Quo\Acpi\Dump:
02:289 00:000 ACPI Load Path      :\Efi\Quo\Acpi\Load:
02:289 00:000 Found Defaults 99F2839C-57C3-411E-ABC3-ADE5267D960D from Fv
02:294 00:004 Acpi Loader Mode 0x004D (Enabled  | Darwin | Windows | Update Legacy)

Sorry i forgot to say, no dsdt was harmed during this boot 

post-840738-0-35449400-1397254497_thumb.png

DSDT.zip

GAZ77MX-D3H-TH-OZ894-F7e.ROM.zip

Link to comment
Share on other sites
ammoune78
ammoune78
Posted
Posted

I dont know what makes this error.

My dsdt works great in windows becouse dont apply any patches to dsdt,i fix errors and only add igpu.hdau,hdef and dtgp manualy.

I know that i get this yellow icon if i apply toleda gpu patches and they rename devices and it seems that this makes errors in windows.

Look at my bios dsdt and make same changes and try.

if u dont know what i mean i will make amiboardinfo.ffs for your board in my way after 1 hour i am busy right now.

 

Doo u use hd 4600 or no?

What patches u need if u dont use hd4600,only hdef ? and hdau for gtx 770 ?

 

Yes PLEASE!

I use GTX 770 and sometimes HD4600 for videos encoding!!!!!!!! Please! :drool:  ^_^  :yes:

The bootlog with dpcimanager 


02:128 00:000 Found Boot0003 "UEFI: C300-CTFDDAC128MAG" (0x32)
02:229 00:101 Found Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz (3A.06.00) Cores 4 Threads 4

Sorry i forgot to say, no dsdt was harmed during this boot 

Hi Aigors!

I think you use Windows both with OS X in one HDD? 02:128 00:000 Found Boot0003 "UEFI: C300-CTFDDAC128MAG" (0x32)

And what's this you have Z87N-Wifi and you have 3570k  :wacko: 02:229 00:101 Found Intel® Core i5-3570K CPU @ 3.40GHz (3A.06.00) Cores 4 Threads 4

Z87N-Wifi=> HASWELL

i5 3570K=> IvyBridge  :surprised:  :wacko:  :whistle: 

Link to comment
Share on other sites
ammoune78
ammoune78
Posted
Posted

does not matter :yes:

Yes i'm totally agree with you!

But this: 02:229 00:101 Found Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz (3A.06.00) Cores 4 Threads 4, even if he use Z87N-Wifi?????

Link to comment
Share on other sites
truemac
truemac
Posted
Posted

The bootlog with dpcimanager 

00:000 00:000 Ozmosis 1.01.0894 RELEASE (2013-12-09 21:54:35 VS2013x86) on 2014-04-11 22:11:27
00:000 00:000 Found Firmware UEFI Spec  :2.31:
00:000 00:000 Found Firmware Vendor     :American Megatrends:
00:000 00:000 Found Firmware Revision   :4.653:
00:000 00:000 Detected Aptio 2.x firmware enabling fixes
00:000 00:000 Embedded Mode Detected
02:126 02:126 BootOrder 01 02 03 (3)
02:128 00:001 Found Boot0001 "Mavericks" (0x14)
02:128 00:000 Found Boot0002 "Recovery HD" (0x18)
02:128 00:000 Found Boot0003 "UEFI: C300-CTFDDAC128MAG" (0x32)
02:229 00:101 Found Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz (3A.06.00) Cores 4 Threads 4
02:229 00:000  BusRatio 16 / 34 (36)
02:229 00:000  P-State Coordination Type HW_ALL -> SW_ANY = SW_ANY
02:229 00:000  Disabling Invalid Flex-Ratio F0000 -> E0000 = E0000
02:229 00:000  TurboBusRatio1 38 -> 38 = 38
02:229 00:000  TurboBusRatio2 38 -> 37 = 38
02:229 00:000  TurboBusRatio3 37 -> 36 = 37
02:229 00:000  TurboBusRatio4 36 -> 35 = 36
02:229 00:000 Calculated TSC Frequency 3403MHz (3403347020)
02:229 00:000 Calculated CPU Frequency 3403MHz (3403346994)
02:229 00:000 Calculated FSB Frequency  100MHz (100098441)
02:229 00:000 Found Intel Graphics Controller [8086:0162] [1458:D000] rev 9
02:229 00:000 Found <null string> Lan Controller [1969:1083] [1458:E000] rev 192 00:00:00:00:00:00
02:229 00:000 Found 7 Series SMBUS Controller [8086:1E22] MMIO 0xDFD15000, IOPort 0xF040
02:253 00:024  Slot 1 4096MB DDR3 SDRAM 1333MHz "Kingston" "9905474-060.A00LF" "9C2FFC69"
02:278 00:024  Slot 3 4096MB DDR3 SDRAM 1333MHz "Kingston" "9905474-060.A00LF" "A02F3A69"
02:284 00:006 Found Storage PciRoot(0x0)/Pci(0x1F,0x2)/Sata(0x0,0xFFFF,0x0)/HD(1,GPT,C73033FC-EB78-4A31-AB10-6340160E3B97,0x28,0x64000)
02:284 00:000 Base Directory Path :\Efi\Quo\:
02:289 00:004 Local Path          :\Efi\Quo\Darwin\:
02:289 00:000 Common Kexts Path   :\Efi\Quo\Darwin\Extensions\:
02:289 00:000 ACPI Dump Path      :\Efi\Quo\Acpi\Dump:
02:289 00:000 ACPI Load Path      :\Efi\Quo\Acpi\Load:
02:289 00:000 Found Defaults 99F2839C-57C3-411E-ABC3-ADE5267D960D from Fv
02:294 00:004 Acpi Loader Mode 0x004D (Enabled  | Darwin | Windows | Update Legacy)

Sorry i forgot to say, no dsdt was harmed during this boot 

try using without this Module |006|FileSystem     |93022F8C-1F09-47EF-BBB2-5814FF609DF5|0003FE9F|007EA1|DRVR|

I do not know if it's good to use FileSystem and EnhancedFat in same time. :no: 

But this: 02:229 00:101 Found Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz (3A.06.00) Cores 4 Threads 4, even if he use Z87N-Wifi?????

is another build than in the signature :)

  • Like 1
Link to comment
Share on other sites
Aigors
Aigors
Posted
Posted

Hello,

 

Just to say i get success with inserting bigger dsdt in bios.  :yes:

I must now write the code to automate this.

 

Fred

GENIUS!!!!! you have a payed beer when wil come in Roma 

Link to comment
Share on other sites
ammoune78
ammoune78
Posted
Posted

 

try using without this Module |006|FileSystem     |93022F8C-1F09-47EF-BBB2-5814FF609DF5|0003FE9F|007EA1|DRVR|

I do not know if it's good to use FileSystem and EnhancedFat in same time. :no: 

is another build than in the signature :)

 

 

AHH Ok!

Now understanding, excuse my stupidity :blush:  :D

Yesterday I made ​​a bad DSDT in AmiBoardInfo, because I was using a modded bios already, and it took me two hours to pass a boot my computer, and the problem was that I did not delete the entire Scope TZ. 

Please again truesoldier!

Can you tell me what i could delete from DSDT without Scope TZ :drool:  :blush:

Hello,

 

Just to say i get success with inserting bigger dsdt in bios.  :yes:

I must now write the code to automate this.

 

Fred

Congratulations our beloved Fred! You are genius, like Aigors said!

Yesterday i've buggered my PC for two ours because i've integrate one damaged DSDT to my AmiBoardInfo, after flash, my PC keep restarting without any shutdown and even if i reboot from the BackUp Bios  :wallbash:  :mad: 

But now it's OK after clearing CMOS :D  :D  :D! And the DSDT with large size will be very useful for us  :yes:  :D  ^_^  :lol:   

Link to comment
Share on other sites
Aigors
Aigors
Posted
Posted

Can you send me you bios and new dsdt to integrate ? i must check for other bios.

 

Fred

Ok Fred, i have to prepare DSDT for board in with working on, give me some time and i prepare everything and send you 

Link to comment
Share on other sites
Thunderbolt
Thunderbolt
Posted
Posted

Ok Fred, i have to prepare DSDT for board in with working on, give me some time and i prepare everything and send you 

 

 

Hey did you mean by saying that it will not work on motherboard because mmtool does not allow the bios file to be loaded ? as thats what is happening. 

 

And Definitely my board is UEFI as I boot Mavericks with UEFI.

 

The is my board

 

ga880gm-usb 3 rev 3.1  (the BIOS is FFe currently in Beta in almost 1 year and I doubt they make a final BIOS for it. But i can try the lower version BIOS).

Link to comment
Share on other sites
xpamamadeus
xpamamadeus
Posted
  • Author
Posted

Hey did you mean by saying that it will not work on motherboard because mmtool does not allow the bios file to be loaded ? as thats what is happening. 

 

And Definitely my board is UEFI as I boot Mavericks with UEFI.

 

The is my board

 

ga880gm-usb 3 rev 3.1  (the BIOS is FFe currently in Beta in almost 1 year and I doubt they make a final BIOS for it. But i can try the lower version BIOS).

Hi,u can replace your dsdt in bios but u cannot use ozmosis from firmware since your bios its award 6 bios.

u can make modification in dsdt using awardtool152 its easier than we have for ami aptio.

use awardtool152 open bios,choose some slic file,go advanced and then dsdt,then choose allow dsdt modification,then edit dsdt_new.dsl and when u done with modification continue and u have done.

Link to comment
Share on other sites
Thunderbolt
Thunderbolt
Posted
Posted

Hi,u can replace your dsdt in bios but u cannot use ozmosis from firmware since your bios its award 6 bios.

u can make modification in dsdt using awardtool152 its easier than we have for ami aptio.

use awardtool152 open bios,choose some slic file,go advanced and then dsdt,then choose allow dsdt modification,then edit dsdt_new.dsl and when u done with modification continue and u have done.

 

 

What ? but there is not dsdt for an AMD Motherboard. And what do you mean by I can replace the dsdt in the BIOS ?  

 

I only have a DSDT which i extracted with DPCIManager but then again it would need patching and there are non for an AMD.

 

But let me try the award tool.

 

I did something and it came with popups that you can edit the dsdt and acpi files and it also created the bios flie. Now what do I do ? do Insert this in the BIOS

 

I honestly don't know how to edit the dsdt and those two ACPI files 

Link to comment
Share on other sites
xpamamadeus
xpamamadeus
Posted
  • Author
Posted

What ? but there is not dsdt for an AMD Motherboard. And what do you mean by I can replace the dsdt in the BIOS ?  

 

I only have a DSDT which i extracted with DPCIManager but then again it would need patching and there are non for an AMD.

 

But let me try the award tool.

 

I did something and it came with popups that you can edit the dsdt and acpi files and it also created the bios flie. Now what do I do ? do Insert this in the BIOS

when u get that popup then just leave this tool like it is.

Go to folder that it display in this popup and there u find dsdt_new.dsl and edit this file,when u done editing this dsl press ok on award tool and u will get bios file that u can flash.

Done.

Link to comment
Share on other sites
Thunderbolt
Thunderbolt
Posted
Posted

when u get that popup then just leave this tool like it is.

Go to folder that it display in this popup and there u find dsdt_new.dsl and edit this file,when u done editing this dsl press ok on award tool and u will get bios file that u can flash.

Done.

 

 

LOL ok but how to edit the new_dsdt which app ? and what changes I should be making in that is what I don't know, And yes it has created a bios file which i guess can be flashed by using the bios flasher from gigabyte

Link to comment
Share on other sites
xpamamadeus
xpamamadeus
Posted
  • Author
Posted

LOL ok but how to edit the new_dsdt which app ? and what changes I should be making in that is what I don't know, And yes it has created a bios file which i guess can be flashed by using the bios flasher from gigabyte

What u want to achieve?

Whats your goal ?

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...