spakk Posted November 2, 2015 Share Posted November 2, 2015 @spakk Thanks for the information, I installed the attachment you gave, now I get "unable to find driver for this platform acpi..." error and even if I replace the original kexts back from Windows it won't boot because I can't repair permissions from Windows, however I can boot to my USB Installation for Yosemite and I can use the terminal there. Is there a command that I can use in terminal to rebuild cache and repair permissions? In Terminal: sudo rm -r /System/Library/Caches/com.apple.kext.caches or use kext Wizard  Link to comment Share on other sites More sharing options...
Shaneee Posted November 5, 2015 Share Posted November 5, 2015 Occasionally I'm getting stuck at AppleKeyStore on boot. Have to hard reboot and use -f to bypass. Tried different versions of FakeSMC but still happening. Would disabling the kernels decryptor help? Â Link to comment Share on other sites More sharing options...
jaylex Posted November 6, 2015 Share Posted November 6, 2015 now I was able to update to the newest enorch chameleon bootloader and the osx boots but at the beginning I get a error message that saids Error encountered while starting up the computer starting in 5 seconds and then it starts and it works normally any ideas?? Link to comment Share on other sites More sharing options...
spakk Posted November 6, 2015 Share Posted November 6, 2015 now I was able to update to the newest enorch chameleon bootloader and the osx boots but at the beginning I get a error message that saids Error encountered while starting up the computer starting in 5 seconds and then it starts and it works normally any ideas?? Â I think that the problem is caused by an incorrect install-settings of Enoch. check how do you have installed Enoch, check according to which content in /Extra/ modules/ is installed. 1 Link to comment Share on other sites More sharing options...
jaylex Posted November 6, 2015 Share Posted November 6, 2015 I think that the problem is caused by an incorrect install-settings of Enoch. check how do you have installed Enoch, check according to which content in /Extra/ modules/ is installed. Thanks for the reponse but this happen after I format one of the partition in the same hard drive after the error it boots fine and everything works fine any ideas? Link to comment Share on other sites More sharing options...
spakk Posted November 7, 2015 Share Posted November 7, 2015 boot your system with an USB flash drive, choose the Yosemite partition, give manually the boot flags and start your system, when you are successful in the system, then open the terminal and give the following code:. diskutil list Then upload the table of diskutil list Link to comment Share on other sites More sharing options...
Bronya Posted November 7, 2015 Share Posted November 7, 2015 Occasionally I'm getting stuck at AppleKeyStore on boot. Have to hard reboot and use -f to bypass. Tried different versions of FakeSMC but still happening. Would disabling the kernels decryptor help? Â IMG_20151105_125203416.jpg try flag -nodecryptor 1 Link to comment Share on other sites More sharing options...
jaylex Posted November 8, 2015 Share Posted November 8, 2015 boot your system with an USB flash drive, choose the Yosemite partition, give manually the boot flags and start your system, when you are successful in the system, then open the terminal and give the following code:. diskutil list Then upload the table of diskutil list  here it is and the partition that is giving me errors is the mac 2.  thanks Link to comment Share on other sites More sharing options...
spakk Posted November 8, 2015 Share Posted November 8, 2015 You can correct me, but I mean that should be the setting for AMD so: PatchAPIC key> No string> because if I want to start my system with chameleon bootloader with ACPI Patcher.dylib (in folder modules) then my system, does not work. Therefore, take this change in your config.plist and start again your system. Your partition is active, I was assuming that the partition is not active. 1 Link to comment Share on other sites More sharing options...
jaylex Posted November 8, 2015 Share Posted November 8, 2015 You can correct me, but I mean that should be the setting for AMD so: <key>PatchAPIC</ key> <string>No</ string> because if I want to start my system with chameleon bootloader with ACPI Patcher.dylib (in folder modules) then my system, does not work. Therefore, take this change in your config.plist and start again your system. Your partition is active, I was assuming that the partition is not active. I cant find the config.plist and im not using clover im just using enorch chameleon bootloader only. do you know where it is? thanks for all the help!! Link to comment Share on other sites More sharing options...
spakk Posted November 8, 2015 Share Posted November 8, 2015 That's easy. The ACPIPatcher.dylib In the folder /Extra/modules/ if should there, then be removed and restart 1 Link to comment Share on other sites More sharing options...
jaylex Posted November 8, 2015 Share Posted November 8, 2015 That's easy. The ACPIPatcher.dylib In the folder /Extra/modules/ if should there, then be removed and restart nope, the file is not there Link to comment Share on other sites More sharing options...
spakk Posted November 8, 2015 Share Posted November 8, 2015 hmmm. I do not understand. Please load your org.chameleon.boot.plist here. and I start my computer, on the phone display is not all easy to recognize. 1 Link to comment Share on other sites More sharing options...
jaylex Posted November 8, 2015 Share Posted November 8, 2015 hmmm. I do not understand. Please load your org.chameleon.boot.plist here. and I start my computer, on the phone display is not all easy to recognize. Â here it is!! Link to comment Share on other sites More sharing options...
spakk Posted November 8, 2015 Share Posted November 8, 2015 I would modify the flags in: -f -v kext-dev-mode=1 npci=0x2000 ....... (make the first boot with -v -f .. later then you can remove these flags) ...chouse your osx ..... throw out the {censored} ... uninteresting but your system booted earlier, what have you done for changes? Note once, never test on the main partition! only on a test partition or better on a external hdd! because the {censored} work to fix the problems you have later. 1 Link to comment Share on other sites More sharing options...
jaylex Posted November 8, 2015 Share Posted November 8, 2015 I would modify the flags in: -f -v kext-dev-mode=1 npci=0x2000 ....... (make the first boot with -v -f .. later then you can remove these flags) ...chouse your osx ..... throw out the {censored} ... uninterestingbut your system booted earlier, what have you done for changes? All I did was delete a maverick partition because I realized that the maverick chameleon boot loader was the one that was booting the Yosemite partition and I didn't want the maverick partition anymore so I delete it. Link to comment Share on other sites More sharing options...
spakk Posted November 8, 2015 Share Posted November 8, 2015 If you have formatted your Main Partition "also Mavericks Partition"Â in this state can your system not boot, this is logical ... so you have now to install Enoch bootloader on your Yosemite Partition, so that your system can be booted. Link to comment Share on other sites More sharing options...
jaylex Posted November 8, 2015 Share Posted November 8, 2015 If you have formatted your Main Partition "also Mavericks Partition"Â in this state can your system not boot, this is logical ... so you have now to install Enoch bootloader on your Yosemite Partition, so that your system can be booted. That's What I did and it works but at boot I get that error and after 5 seconds then it boots normally!! Link to comment Share on other sites More sharing options...
Shaneee Posted November 8, 2015 Share Posted November 8, 2015 @jaylex what partition shown here is Enoch installed on? Bootloader should be installed on the first partition in your case its "DISCO" (disk2s2) 1 Link to comment Share on other sites More sharing options...
jaylex Posted November 8, 2015 Share Posted November 8, 2015 @jaylex what partition shown here is Enoch installed on? Bootloader should be installed on the first partition in your case its "DISCO" (disk2s2)I don't want that partition anymore can i change MAC 2 Partition to disk2s2?  Thanks in advance! Link to comment Share on other sites More sharing options...
atlee Posted November 9, 2015 Share Posted November 9, 2015 All the newer kernels seem incomptible with VoodooHDA in my Hackintosh. Why not hex edit latest AppleHDA binary and create your own mapping so you get better sound (Chances are someone has already created one for ALC-887)? i.e. do a linux dump of ALC 887, convert verbs to a readable format then do abit of tweaking and testing (yes process is a little more detailed then what I have said). Link to comment Share on other sites More sharing options...
spakk Posted November 9, 2015 Share Posted November 9, 2015 Why not hex edit latest AppleHDA binary and create your own mapping so you get better sound (Chances are someone has already created one for ALC-887)? i.e. do a linux dump of ALC 887, convert verbs to a readable format then do abit of tweaking and testing (yes process is a little more detailed then what I have said). that will not work with any internal sound card on AMD Hackintosh! Link to comment Share on other sites More sharing options...
spakk Posted November 9, 2015 Share Posted November 9, 2015 put your second partition active, similarly is described here. http://www.insanelymac.com/forum/topic/22844-how-to-setting-your-partition-active-using-fdisk-in-macosx/or create a clone of your second partition on your first partition, and finally install the bootloader on it. Link to comment Share on other sites More sharing options...
jaylex Posted November 9, 2015 Share Posted November 9, 2015 put your second partition active, similarly is described here. http://www.insanelymac.com/forum/topic/22844-how-to-setting-your-partition-active-using-fdisk-in-macosx/or create a clone of your second partition on your first partition, and finally install the bootloader on it. I really don't know what is going on I erase the whole disk to start from Scratch and it still showing the same error. Please help!!! Link to comment Share on other sites More sharing options...
Mr. Xtreme Posted November 9, 2015 Share Posted November 9, 2015 Screen record a video of what your doing with say obs (open broadcaster software). Link to comment Share on other sites More sharing options...
Recommended Posts