k.panic Posted August 1, 2015 Share Posted August 1, 2015 mckay_kernel -v cpus=2 busratio=27 => stuck at PCI Configuration Begin then boot with npci=0x2000 or npci=0x3000 (...es wird schon gelingen :-)), nicht ärgern) Edit: I suspect that the information for busratio are too high! check this information! probably > 20 my dsdt (thanks!) I'm trying with busratio=20.. EDIT: mckay_kernel -v cpus=2 PCIRootUID=1 npci=0x3000 (or 2000) stuck at System uptime in nanoseconds.. (A4-3400 have 100x27 = 2700?) In bios we have CPU Clock Ratio [Auto] 2700MHz CPU MB Clock Divisor [Auto] 720MHz CPU Host Clock Control [Auto] CPU Frequency [100] Link to comment Share on other sites More sharing options...
spakk Posted August 1, 2015 Share Posted August 1, 2015 there were a few errors in the included dsdt - now adjusted. If your system is running, then make a ioreg-file to modify the other values my dsdt (thanks!) I'm trying with busratio=20.. EDIT: mckay_kernel -v cpus=2 PCIRootUID=1 npci=0x3000 (or 2000) stuck at System uptime in nanoseconds.. (A4-3400 have 100x27 = 2700?) In bios we have CPU Clock Ratio [Auto] 2700MHz CPU MB Clock Divisor [Auto] 720MHz CPU Host Clock Control [Auto] CPU Frequency [100] Sorry, the busratio value seemed to be high, ie 27 and not 20 stuck at System uptime in nanoseconds. .... then make an image of the kernel panic and upload it here modified_dsdt_ifmg.zip 1 Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 thanks! this is the KP Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 Bronya will be able to tell you with great certainty what the cause of this panic message is. or you wait a little while until it comes back online.but you can try following:In annexed, I have a few drivers that I use for my Gigibyte Board, possibly you do not have the chipset drivers.?extract the attachment and install the contents of the Extensions folder to /Extra/Extensions/then edit the bootargs in your org.chameleon.boot.plist with the additional change: -v -f npci=0x3000 CPUs=2 busratio=27 fsb=100 UseKernelCache=NO and test it with : GraphicsEnabler=NO PCIRootUID=1 or PCIRootUID=0 Extensions.zip 1 Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 Bronya will be able to tell you with great certainty what the cause of this panic message is. or you wait a little while until it comes back online. but you can try following: In annexed, I have a few drivers that I use for my Gigibyte Board, possibly you do not have the chipset drivers.? extract the attachment and install the contents of the Extensions folder to /Extra/Extensions/ then edit the bootargs in your org.chameleon.boot.plist with the additional change: -v -f npci=0x3000 CPUs=2 busratio=27 fsb=100 UseKernelCache=NO and test it with : GraphicsEnabler=NO PCIRootUID=1 or PCIRootUID=0 I've changed Kernel and with your Extensions and flags "-v -f npci=0x3000 CPUs=2 busratio=27 fsb=100 UseKernelCache=NO PCIRootUID=1/0" I've a White Screen with a black cursor! It's a big progress! Thanks! Now, why I can't see anything, in addition to the white screen? EDIT: take me few minutes pls.. 1 Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 (edited) that's once a big step forward . Please upload your complete /Extra/ folder as a zip file . Edit: I want to check whether you have everything installed correctly. Edited August 2, 2015 by spakk 1 Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 (edited) I need a few minutes, in the meantime I can tell you which folder Extra I only put: your Kext in /extensions 1002_9644.rom dsdt.aml My Extra folder EDIT: with APU on VGA Port (flags -v -f npci=0x300 cpus=2 busratio=27 fsb=100 UseKernelCache=No PCIRootUID=1) stuck at [iOBluetoothHCIController][start]-- completed with GT210 on VGA Port (flags -v -f npci=0x300 cpus=2 busratio=27 fsb=100 UseKernelCache=No PCIRootUID=1) white screen and black cursor Edited August 2, 2015 by lfmg Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 sorry, had been busy with something else, use the contents of the notes. After booting press Enter and report. Extra.zip 1 Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 (edited) sorry, had been busy with something else, use the contents of the notes. After booting press Enter and report. don't worry! I'm trying now to boot Edit: the GT210 should work with Mountain Lion or Mavericks ... although it is not the Burner, but okay ....do you have created the USB Installer with myhack.app? If so, then no problem ... otherwise you need later to connect the HDD on an OS X system..... to install the other things like as bootloader, Extra folder, amd kernel. Edited August 2, 2015 by spakk Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 another big step! did I do something wrong? 1 Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 What happened? 1 Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 after select Language, it says which can not complete the installation.. Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 (edited) the system is frozen. If the system is frozen, then boot again, then format the target partition where you want to install OS X. then let show only the errors messages (you can select at the top) so that we know whether any data packet is corrupted under /System/Library/install/package/... into USB installer .. etc ...then we can to fix the problem. Edit: is the target HDD empty? or is there your Windows operation system installed? watch out. otherwise clamp the Windows HDD on the SATA slot, not that you accidentally make a mistake. - No idea how much OS X knowledge you have. Edit: I think that the USB Installer is not installed correctly , therefore the system freeze . I think you should create the USB again . use myhack.app Edited August 2, 2015 by spakk Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 yes, I use myhack.app.. http://www.filedropper.com/outlookcom after initializing the hard drive from NTFS to HFS +, after restarting the system crashes at [iOBluetoothHCIController][start]-- completed Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 Boot with: -x and the other flags or boot with usb stick and repair the permissions and start again Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 (edited) Boot with: -x and the other flags yes, I've booted with that flags.. EDIT: I'm trying with another usbdrive.. Edited August 2, 2015 by lfmg Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 look here, might it can help you, to resolve the problem: : https://m.youtube.com/watch?v=sYLTcd5TwGk Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 look here, might it can help you, to resolve the problem: : https://m.youtube.com/watch?v=sYLTcd5TwGk sorry, my fault.. I'm here now.. http://www.filedropper.com/outlookcom Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 Have you saved the log? In the pictures you can see little. Probably a problem, the files will not be written entirely on your target HDD. start from the beginning: install the myhack3.3.1 version, create the usb installer .... etc .. 2.boot with USB Installer and reformat your target disk with the "GUID" partition table ... The format of HDD should "Mac OS X Extended (Journaled)" to be. If you've done all that, then you should be able to install. Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 (edited) Have you saved the log? In the pictures you can see little. Probably a problem, the files will not be written entirely on your target HDD. start from the beginning: install the myhack3.3.1 version, create the usb installer .... etc .. 2.boot with USB Installer and reformat your target disk with the "GUID" partition table ... The format of HDD should "Mac OS X Extended (Journaled)" to be. If you've done all that, then you should be able to install. It crashed before I can choose partition.. Just after language selection.. No, I can't, in no way, to save Log File, even on an external memory stick! EDIT: I finally managed to save the Log http://www.filedropper.com/resocontoinstallazione2-aug-2015 Edited August 2, 2015 by lfmg Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 Then, the problem occurred in the preparation of USB Installer! That would not be the first time. We all have had that before. One more time, create a new USB Installer !! either myhack 3.3.1.app or with the Disk Utility (there are many good and simple examples on youtube) then add the Extra folder, and then install the current bootloader see here Then your system will be installed correctly, I think. Edit: I'll be looking at equal your protocol myHack 3.3.1.zip Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 Then, the problem occurred in the preparation of USB Installer! That would not be the first time. We all have had that before. One more time, create a new USB Installer !! either myhack 3.3.1.app or with the Disk Utility (there are many good and simple examples on youtube) then add the Extra folder, and then install the current bootloader see here Then your system will be installed correctly, I think. Edit: I'll be looking at equal your protocol I am preparing (with myhack 3.3.1) a new USB Installer with another InstallESD.dmg of mavericks .. to take away any doubt! 1 Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 It's not easy for me to make a statement from the log. (possibly wait until Bronya again is online.)??what happens when you booting without cpus=2 ?have you trying to boot with: arch=x86_64 ? Link to comment Share on other sites More sharing options...
k.panic Posted August 2, 2015 Share Posted August 2, 2015 (edited) It's not easy for me to make a statement from the log. (possibly wait until Bronya again is online.)?? what happens when you booting without cpus=2 ? have you trying to boot with: arch=x86_64 ? same error/crash.. Have I to install Enoch on USB Installer? p.s. I have no hurry ;) Edited August 2, 2015 by lfmg Link to comment Share on other sites More sharing options...
spakk Posted August 2, 2015 Share Posted August 2, 2015 Yes use Enoch, I also use Enoch for Yosemite 1 Link to comment Share on other sites More sharing options...
Recommended Posts