Jump to content

Clover General discussion

ErmaC

By ErmaC,
in Clover

 Share
30,171 posts in this topic

Recommended Posts

nmano
nmano
Posted
Posted

Red color is allowed only for moderators.

 

I didn't understand your post about UUID, DTGP and _DSM. If it is some other manual then read it and follow it. Ask the author why you have a problem.

I give you a link on my instructions and I see you don't follow them.

When done upload DarwinDumper report with your results to discuss what is working and what no.

Hi I don't know about colour code so sorry.

I upload my files DarwinDumper report

 

http://www.mediafire.com/download/4hd7fbj391tphof/005_2016-05-17_22-21-52_MacPro6%2C1.zip

Link to comment
Share on other sites
Slice
Slice
Posted
Posted

Sorry for my ignorance but what is "RefCLK" under Graphics?

It was attempt to boost graphics. Seems not affects.

 

Hi I don't know about colour code so sorry.

I upload my files DarwinDumper report

 

http://www.mediafire.com/download/4hd7fbj391tphof/005_2016-05-17_22-21-52_MacPro6%2C1.zip

The report excluding BIOS and compressed as LZMA occupy 100kb and can be attached to post.

OK, I took it and look now. 

  • Like 1
Link to comment
Share on other sites
nmano
nmano
Posted
Posted

Test with this DSDT

attachicon.gifDSDT.aml.zip

Yes I test your DSDT its work this.

 

pci104c,8235:

 

  Type: IEEE 1394 Open HCI

  Driver Installed: Yes

  MSI: No

  Bus: PCI

  Slot: Ethernet@3,0,0

  Vendor ID: 0x104c

  Device ID: 0x8235

  Subsystem Vendor ID: 0x14db

  Subsystem ID: 0x0000

 

  Revision ID: 0x0001

DarwinDumper_2.9.9.1_AMI_X64_3438_Cap_manoranjan.zip

Link to comment
Share on other sites
Slice
Slice
Posted
Posted

 

Yes I test your DSDT its work this.

 

pci104c,8235:

 

  Type: IEEE 1394 Open HCI

  Driver Installed: Yes

  MSI: No

  Bus: PCI

  Slot: Ethernet@3,0,0

  Vendor ID: 0x104c

  Device ID: 0x8235

  Subsystem Vendor ID: 0x14db

  Subsystem ID: 0x0000

 

  Revision ID: 0x0001

 

To make more devices you have to add

Name (_SUN, 0x6) then 7,8,9,  0xA, 0xB... for each interesting Device()

and then add Slot information into you config.plist Smbios section where you already have device=Nvidia ID=0 not corresponding _SUN property of the device.

Read instructions again.

Link to comment
Share on other sites
nmano
nmano
Posted
Posted

To make more devices you have to add

Name (_SUN, 0x6) then 7,8,9,  0xA, 0xB... for each interesting Device()

and then add Slot information into you config.plist Smbios section where you already have device=Nvidia ID=0 not corresponding _SUN property of the device.

Read instructions again.

what about Built IN Device HDEF ID?

Name (_SUN, 0x6)

Link to comment
Share on other sites
tuanpekoe
tuanpekoe
Posted
Posted

I have just updated OSX to 10.11.5, and got a issue with OsxAptioFixDrv.efi when booting to OSX.

I had to use OsxAptioFix2Drv.efi instead. It worked fine, but i still want to utilize OsxAptioFixDrv.efi

Anyone here have an idea for that?

Link to comment
Share on other sites
nmano
nmano
Posted
Posted

what about Built IN Device HDEF ID?

Name (_SUN, 0x6)

thanks Slice

Its worked now.

Thank you for your hard work.

Its worked auto with sun ID.

I update my DSDT all slot worked but HDEF Slot not show.

post-413859-0-13834200-1463582494_thumb.png

DSDT.aml.zip

Link to comment
Share on other sites
Riley Freeman
Riley Freeman
Posted
Posted

I have just updated OSX to 10.11.5, and got a issue with OsxAptioFixDrv.efi when booting to OSX.

I had to use OsxAptioFix2Drv.efi instead. I worked fine, but i still want to utilize OsxAptioFixDrv.efi

Anyone here have an idea for that?

 

If you have SIP (partially) enabled you need to disable protected nvram to use AptioFixDrv.

Link to comment
Share on other sites
tluck
tluck
Posted
Posted

yup - this has fixed up things for me...

<key>RtVariables</key>
<dict>
  <key>BooterConfig</key>
  <string>0x28</string>
  <key>CsrActiveConfig</key>
  <string>0x43</string>
Link to comment
Share on other sites
Slice
Slice
Posted
Posted

thanks Slice

Its worked now.

Thank you for your hard work.

Its worked auto with sun ID.

I update my DSDT all slot worked but HDEF Slot not show.

Looks like HDEF and HDMI have another rules to shown or not here.

Link to comment
Share on other sites
Philip Petev
Philip Petev
Posted
Posted

 

....................

Building ... /Users/philip/Repo/CloverGrowerPro/edk2/Clover/Library/OsxBdsPlatformLib/PlatformBds.inf [X64]

[CC] AutoGen

[sLINK] CustomizedDisplayLib

Building ... /Users/philip/Repo/CloverGrowerPro/edk2/MdePkg/Library/BasePciCf8Lib/BasePciCf8Lib.inf [X64]

[CC] HiiLanguage

/bin/sh: /Users/philip/src/opt/local/bin/nasm: No such file or directory

[sLINK] UefiHiiLib

make: *** [/users/philip/Repo/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC49/X64/MdePkg/Library/BaseLib/BaseLib/OUTPUT/X64/Thunk16.obj] Error 127

 

 

build.py...

 : error 7000: Failed to execute command

    make tbuild [/users/philip/Repo/CloverGrowerPro/edk2/Build/Clover/RELEASE_GCC49/X64/MdePkg/Library/BaseLib/BaseLib]

 

 

build.py...

 : error F002: Failed to build module

    /Users/philip/Repo/CloverGrowerPro/edk2/MdePkg/Library/BaseLib/BaseLib.inf [X64, GCC49, RELEASE]

 

- Failed -

Build end time: 23:29:10, May.18 2016

Build total time: 00:00:17

 

Cloverx64 release  ERROR!!

 

 

Ejecting RAM disk

"disk1" unmounted.

"disk1" ejected.

 

Why the hell it looks for nasm in /Users/philip/src/opt/local/bin/? It's not there, it's in /Users/philip/Repo/CloverGrowerPro/toolchain/bin.

Link to comment
Share on other sites
Slice
Slice
Posted
Posted

Why the hell it looks for nasm in /Users/philip/src/opt/local/bin/? It's not there, it's in /Users/philip/Repo/CloverGrowerPro/toolchain/bin.

Because nobody supported CloverGrowerPro.

  • Like 1
Link to comment
Share on other sites
Rodion2010
Rodion2010
Posted
Posted

Why the hell it looks for nasm in /Users/philip/src/opt/local/bin/? It's not there, it's in /Users/philip/Repo/CloverGrowerPro/toolchain/bin.

Because it is exactly in /src/opt/local/bin/

 ​Don't use ClowerGrover and it will be OK   :)

Link to comment
Share on other sites
Denicio
Denicio
Posted
Posted

Because Is not :D.  (virtual box && grub only)

 

Just did a clean install on the EFI partition with Clover r3526. Look at the default "drivers64UEFI" folder after the installation.

post-99742-0-71096800-1463610652_thumb.jpg

Link to comment
Share on other sites
Micky1979
Micky1979
Posted
Posted

you are right!

        <choice
		id="HFSPlus.UEFI"
		title="HFSPlus.UEFI_title"
		description="HFSPlus.UEFI_description"
		start_visible="false" start_selected="true">
		<pkg-ref id="org.clover.drivers64uefi.mandatory.hfsplus.uefi"/>
	</choice>

invisible and selected. :blink:, I think is unwanted  ^_^

Link to comment
Share on other sites
benww
benww
Posted
Posted

Hi, I don't know if it's suitable to ask something about CPU speedstep with Clover here.

 

My issue is described here: https://github.com/Piker-Alpha/ssdtPRGen.sh/issues/215 (Sorry for putting a link here but that contains some details that are too long to repost here.)

It's about turboboost not working correctly. With Clover, not selecting anything in ACPI->SSDT, only 2 steps above normal clock speed can be reached. Tried selecting some options there but with no luck.

 

Here is my boot.log:

0:100  0:100  MemLog inited, TSC freq: 1873193743
0:100  0:000  LegacyRegion2: Chipset/proc: 0xD1308086
0:100  0:000   Core i7 processors (PAM 0x40-0x47)
0:100  0:000   Test PAM1=(0x41=11, 0x5a=00, 0x81=0D, 0x91=11) at chipset D1308086
0:100  0:000  , Install = Success
0:115  0:015  BiosVideoDriverBindingStart!
0:115  0:000  BiosVideoCheckForVbe
0:115  0:000  EdidOverride not found
0:147  0:032   Edid1+
0:147  0:000   found Detail Timing 2597x90
0:147  0:000   found Detail Timing 2645x90
0:147  0:000   found Detail Timing 2645x90
0:147  0:000   found Detail Timing 2645x90
0:180  0:032   Edid0+
0:180  0:000   found Detail Timing 1920x1080
0:180  0:000   found Detail Timing 1280x720
0:236  0:056     0 640x480 attr=3BF - ok, edid+, 640x480, working, highest, pref=0
0:238  0:002     1 800x600 attr=3BF - ok, edid+, 800x600, working, highest, pref=1
0:241  0:002     2 1024x768 attr=3BF - ok, edid+, 1024x768, working, highest, pref=2
0:243  0:002     3 1280x1024 attr=3BF - ok, edid+, working, highest, pref=3
0:255  0:011     4 1280x800 attr=3BF - ok, edid+, working
0:255  0:000  BV new mode: 3 1280x1024
0:531  0:276   SetMode pref 3 (3) = Success
2:208  1:677  
2:208  0:000  Now is 21.5.2016,  16:58:47 (GMT)
2:208  0:000  Starting Clover rev 3504 on CLOVER EFI
2:208  0:000  Build with: [Args: ./ebuild.sh | Command: build -D USE_LOW_EBDA -p Clover/Clover.dsc -a X64 -b RELEASE -t XCODE5 -n 5 | OS: 10.11.5 | XCODE: 7.3]
2:208  0:000  SelfDevicePath=PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,38632112-1922-4A5E-81C1-BCBF7876AEBE,0x800,0xFA000) @DE87C798
2:208  0:000  SelfDirPath = \EFI\CLOVER
2:208  0:000  Total Memory Slots Count = 4
2:208  0:000  Type 17 Index = 0
2:208  0:000  SmbiosTable.Type17->Speed = 1333MHz
2:208  0:000  SmbiosTable.Type17->Size = 4096MB
2:208  0:000  SmbiosTable.Type17->Bank/Device = BANK0 DIMM0
2:208  0:000  SmbiosTable.Type17->Vendor = Manufacturer0
2:208  0:000  SmbiosTable.Type17->SerialNumber = SerNum0
2:208  0:000  SmbiosTable.Type17->PartNumber = PartNum0
2:208  0:000  Type 17 Index = 1
2:208  0:000  Ignoring insane frequency value 0MHz
2:208  0:000  SmbiosTable.Type17->Speed = 0MHz
2:208  0:000  SmbiosTable.Type17->Size = 0MB
2:208  0:000  SmbiosTable.Type17->Bank/Device = BANK1 DIMM1
2:208  0:000  SmbiosTable.Type17->Vendor = <null string>
2:208  0:000  SmbiosTable.Type17->SerialNumber = <null string>
2:208  0:000  SmbiosTable.Type17->PartNumber = <null string>
2:208  0:000  Type 17 Index = 2
2:208  0:000  Ignoring insane frequency value 0MHz
2:208  0:000  SmbiosTable.Type17->Speed = 0MHz
2:208  0:000  SmbiosTable.Type17->Size = 0MB
2:208  0:000  SmbiosTable.Type17->Bank/Device = BANK2 DIMM2
2:208  0:000  SmbiosTable.Type17->Vendor = <null string>
2:208  0:000  SmbiosTable.Type17->SerialNumber = <null string>
2:208  0:000  SmbiosTable.Type17->PartNumber = <null string>
2:208  0:000  Type 17 Index = 3
2:208  0:000  Ignoring insane frequency value 0MHz
2:208  0:000  SmbiosTable.Type17->Speed = 0MHz
2:208  0:000  SmbiosTable.Type17->Size = 0MB
2:208  0:000  SmbiosTable.Type17->Bank/Device = BANK3 DIMM3
2:208  0:000  SmbiosTable.Type17->Vendor = <null string>
2:208  0:000  SmbiosTable.Type17->SerialNumber = <null string>
2:208  0:000  SmbiosTable.Type17->PartNumber = <null string>
2:208  0:000  Boot status=0
2:208  0:000  Clover revision: 3504  running on System Product Name
2:208  0:000  ... with board P7H55
2:208  0:000  CPU Vendor = 756E6547 Model=106E5
2:208  0:000  got cores from CPUID_1 = 0
2:208  0:000  The CPU supported turbo
2:208  0:000  BrandString = Intel(R) Xeon(R) CPU           L3426  @ 1.87GHz
2:208  0:000  FSBFrequency=133MHz DMIvalue=133330kHz
2:208  0:000  Corrected FSBFrequency=133MHz
2:208  0:000  Vendor/Model/Stepping: 0x756E6547/0x1E/0x5
2:208  0:000  Family/ExtFamily: 0x6/0x0
2:208  0:000  MaxDiv/MinDiv: 14.0/9
2:208  0:000  Turbo: 16/16/23/24
2:208  0:000  Features: 0xBFEBFBFF
2:208  0:000  Threads: 8
2:208  0:000  Cores: 4
2:208  0:000  FSB: 133 MHz
2:208  0:000  CPU: 1866 MHz
2:208  0:000  TSC: 1866 MHz
2:208  0:000  PIS: 533 MHz
2:208  0:000  PCI (00|00:00.00) : 8086 D130 class=060000
2:208  0:000  PCI (00|00:03.00) : 8086 D138 class=060400
2:208  0:000  PCI (00|01:00.00) : 10DE 0DE1 class=030000
2:208  0:000  Found NVidia model=nVidia GeForce GT 430 family #x
2:208  0:000  PCI (00|01:00.01) : 10DE 0BEA class=040300
2:208  0:000  PCI (00|00:08.00) : 8086 D155 class=088000
2:208  0:000  PCI (00|00:08.01) : 8086 D156 class=088000
2:208  0:000  PCI (00|00:08.02) : 8086 D157 class=088000
2:208  0:000  PCI (00|00:08.03) : 8086 D158 class=088000
2:208  0:000  PCI (00|00:10.00) : 8086 D150 class=088000
2:208  0:000  PCI (00|00:10.01) : 8086 D151 class=088000
2:208  0:000  PCI (00|00:1A.00) : 8086 3B3C class=0C0320
2:208  0:000  PCI (00|00:1B.00) : 8086 3B56 class=040300
2:208  0:000  PCI (00|00:1C.00) : 8086 3B42 class=060400
2:208  0:000  PCI (00|00:1C.05) : 8086 3B4C class=060400
2:208  0:000  PCI (00|02:00.00) : 10EC 8168 class=020000
2:208  0:000  LAN 0, Vendor=10EC, MMIO=E800
2:208  0:000  PCI (00|00:1D.00) : 8086 3B34 class=0C0320
2:209  0:000  PCI (00|00:1E.00) : 8086 244E class=060401
2:209  0:000  PCI (00|00:1F.00) : 8086 3B06 class=060100
2:209  0:000  PCI (00|00:1F.02) : 8086 3B22 class=010601
2:209  0:000  PCI (00|00:1F.03) : 8086 3B30 class=0C0500
2:209  0:000  PCI (00|3F:00.00) : 8086 2C50 class=060000
2:209  0:000  PCI (00|3F:00.01) : 8086 2C81 class=060000
2:209  0:000  PCI (00|3F:02.00) : 8086 2C90 class=060000
2:209  0:000  PCI (00|3F:02.01) : 8086 2C91 class=060000
2:209  0:000  PCI (00|3F:03.00) : 8086 2C98 class=060000
2:209  0:000  PCI (00|3F:03.01) : 8086 2C99 class=060000
2:209  0:000  PCI (00|3F:03.02) : 8086 2C9A class=060000
2:209  0:000  PCI (00|3F:03.04) : 8086 2C9C class=060000
2:209  0:000  PCI (00|3F:04.00) : 8086 2CA0 class=060000
2:209  0:000  PCI (00|3F:04.01) : 8086 2CA1 class=060000
2:209  0:000  PCI (00|3F:04.02) : 8086 2CA2 class=060000
2:209  0:000  PCI (00|3F:04.03) : 8086 2CA3 class=060000
2:209  0:000  PCI (00|3F:05.00) : 8086 2CA8 class=060000
2:209  0:000  PCI (00|3F:05.01) : 8086 2CA9 class=060000
2:209  0:000  PCI (00|3F:05.02) : 8086 2CAA class=060000
2:209  0:000  PCI (00|3F:05.03) : 8086 2CAB class=060000
2:209  0:000  Clover load options size = 0 bytes
2:210  0:001  Using OEM config.plist at path: EFI\CLOVER\config.plist
2:210  0:000  EFI\CLOVER\config.plist loaded: Success
2:211  0:000  Found theme directory: embedded
2:212  0:000  Found theme directory: random
2:213  0:000  Found theme directory: bootcamp2.0
2:214  0:001  Found theme directory: b&b
2:216  0:001  Loading early settings
2:216  0:000  timeout set to 3
2:216  0:000  Custom boot CUSTOM_BOOT_DISABLED (0x0)
2:216  0:000  KextsToPatch: 1 requested
2:216  0:000  KextsToPatch 0: AppleAHCIPort (External icons patch) Kext bin patch, data len: 8
2:216  0:000  Default theme: b&b
2:216  0:000  Hiding entries with string Software
2:216  0:000  Hiding entries with string Media
2:216  0:000  Hiding entries with string \EFI\BOOT\BOOTX32.EFI
2:216  0:000  Hiding entries with string \EFI\BOOT\BOOTX64.EFI
2:216  0:000  Hiding entries with string Game
2:216  0:000  CustomEDID ok
2:216  0:000  LoadDrivers() start
2:216  0:000  Loading FSInject-64.efi  status=Success
2:217  0:000  Loading VBoxHfs-64.efi  status=Success
2:217  0:000   - driver needs connecting
2:217  0:000  Loading CsmVideoDxe-64.efi  status=Success
2:218  0:001   - driver needs connecting
2:218  0:000  Video bios patch requested or CustomEDID - forcing video reconnect
2:218  0:000  3 drivers needs connecting ...
2:218  0:000  PlatformDriverOverrideProtocol->GetDriver overriden
2:218  0:000  Video driver loaded: disconnect Success
2:314  0:095  VideoBiosPatchNativeFromEdid:
2:314  0:000   Bios: nVidia, nv_data_table_offset: 0x267, nv_data_table: 0xC0269, std_vesa: 0xC41B5, nv_mode_table: 0xC41BA, mode_table_size: 0x10
2:314  0:000   VideoBiosPatchInit(LegacyRegion = Not Found, LegacyRegion2 = Success) = Success
2:314  0:000   VideoBiosUnlock:  unlocked
2:314  0:000   Patching: BT_NVDA
2:314  0:000   Parse Edid: descriptor block 0 is timing descriptor (h_active: 1920, v_active: 1080, h_sync_offset: 88, h_sync_width: 44, h_blanking: 280, v_blanking: 45, pixel_clock: 14850, v_sync_offset: 4, v_sync_width: 5)
2:315  0:000   patch 0: patched 1 time(s)
2:315  0:000   patch 1: patched 1 time(s)
2:315  0:000   patch 2: patched 1 time(s)
2:316  0:000   patch 3: patched 1 time(s)
2:316  0:000   VideoBiosLock: Success
2:325  0:008  BiosVideoDriverBindingStart!
2:325  0:000  BiosVideoCheckForVbe
2:325  0:000  EdidOverrideFound!
2:325  0:000   found Detail Timing 1920x1080
2:325  0:000   found Detail Timing 1280x720
2:382  0:057     0 640x480 attr=3BF - ok, edid+, 640x480, working, highest, pref=0
2:384  0:002     1 800x600 attr=3BF - ok, edid+, 800x600, working, highest, pref=1
2:386  0:002     2 1024x768 attr=3BF - ok, edid+, 1024x768, working, highest, pref=2
2:388  0:002     3 1280x1024 attr=3BF - ok, edid+, working, highest, pref=3
2:399  0:010     4 1920x1080 attr=3BF - ok, edid+, working, highest, pref=4
2:401  0:002     5 1280x800 attr=3BF - ok, edid+, working
2:401  0:000  BV new mode: 4 1920x1080
2:819  0:417   SetMode pref 4 (4) = Success
3:207  0:387  LoadDrivers() end
3:207  0:000  SetScreenResolution: 1920x1080 - already set
3:207  0:000  Console modes reported: 4, available modes:
3:207  0:000    Mode 1: 80x25
3:207  0:000    Mode 2: 80x50
3:207  0:000    Mode 3: 100x31
3:207  0:000    Mode 4: 240x56 (current mode)
3:207  0:000  SetScreenResolution: 1920x1080 - already set
3:207  0:000  reinit: self device path=PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,38632112-1922-4A5E-81C1-BCBF7876AEBE,0x800,0xFA000)
3:208  0:001  ScanSPD() start
3:208  0:000  SMBus CmdReg: 0x103
3:208  0:000  Scanning SMBus [8086:3B30], mmio: 0xF5FFC004, ioport: 0x400, hostc: 0x1
3:208  0:000  Slots to scan [8]...
3:209  0:000  SPD[0]: Type 11 @0x50 
3:227  0:018  DDR speed 1333MHz 
3:227  0:000  Slot: 0 Type 24 4096MB 1333MHz Vendor=Kingston PartNo=99P5474-014.A00LF SerialNo=0809010C0E0C070B 
3:228  0:001  ScanSPD() end
3:228  0:000  Get Acpi Tables List from RSDT:
3:228  0:000   Found table: FACP  TC-5H    len=132
3:228  0:000   Found table: SLIC  TC-5H    len=374
3:228  0:000   Found table: APIC  APIC1349 len=204
3:228  0:000   Found table: MCFG  OEMMCFG  len=60
3:228  0:000   Found table: OEMB  OEMB1349 len=114
3:228  0:000   Found table: HPET  OEMHPET  len=56
3:228  0:000   Found table: SSDT  CpuPm len=867
3:228  0:000  Calibrated TSC frequency =1873193743 =1873MHz
3:229  0:000  Loading main settings
3:229  0:000  Config set Fixes will override FixMask mask!
3:229  0:000     final mask=00008071
3:229  0:000  Config set ChassisType=0x6
3:229  0:000  Config set CpuType=501
3:229  0:000  found 9 volumes with blockIO
3:229  0:000   0. Volume:
3:229  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)
3:230  0:000    Result of bootcode detection: bootable unknown (legacy)
3:230  0:000   1. Volume:
3:230  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x1,0x0,0x0)
3:230  0:000   2. Volume:
3:230  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,38632112-1922-4A5E-81C1-BCBF7876AEBE,0x800,0xFA000)
3:230  0:000    Result of bootcode detection: bootable Clover (clover)
3:230  0:000    This is SelfVolume !!
3:230  0:000   3. Volume:
3:230  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(2,GPT,574A2654-5284-4D71-81C1-BCBF78739A8A,0xFA800,0x15A29800)
3:230  0:000    Result of bootcode detection: bootable Windows (vista,win)
3:230  0:000   4. Volume:
3:230  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(3,GPT,4185242B-76F6-42FA-B906-17490DA82D94,0x15B24000,0x628A568)
3:231  0:000   5. Volume:
3:231  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(4,GPT,7EC35348-4005-4229-A7BE-998D79EC7F6C,0x1BDEE568,0x135F20)
3:231  0:000   6. Volume:
3:231  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x1,0x0,0x0)\HD(1,GPT,70B144FC-701B-45BE-91CE-26D1E706C7F8,0x800,0xC8000)
3:232  0:000    Result of bootcode detection: bootable Windows (win)
3:233  0:001   7. Volume:
3:233  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x1,0x0,0x0)\HD(2,GPT,CDEC99F5-8FC6-42F2-B8F1-7E7520E71EEF,0x12C028,0xE64D9F99)
3:233  0:000    Result of bootcode detection: bootable Windows (vista,win)
3:233  0:000   8. Volume:
3:233  0:000    PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x1,0x0,0x0)\HD(3,GPT,AC2C71FD-2EE7-44F1-A279-ADD243C3D7CD,0xE6606A8D,0x2800A34)
3:234  0:000    Result of bootcode detection: bootable Windows (vista,win)
3:235  0:001  PutNvramPlistToRtVars: nvram.plist not found
3:235  0:000  Using theme 'b&b' (EFI\CLOVER\themes\b&
3:235  0:000  Warning! Character width should be even!
3:251  0:015  Choosing theme b&b
3:251  0:000  Custom entries start
3:251  0:000  Custom entry 0 FullTitle:"Windows 10" Path:"\EFI\Microsoft\bootmgr.efi" Options:"-s -h" Type:7 Flags:0x0 matching Volume:"C12A7328-F81F-11D2-BA4B-00A0C93EC93B"
3:251  0:000      Checking volume "EFI" (PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,38632112-1922-4A5E-81C1-BCBF7876AEBE,0x800,0xFA000)) ... skipped
3:251  0:000      Checking volume "El Capitan" (PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(3,GPT,4185242B-76F6-42FA-B906-17490DA82D94,0x15B24000,0x628A568)) ... skipped
3:251  0:000      Checking volume "Recovery HD" (PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(4,GPT,7EC35348-4005-4229-A7BE-998D79EC7F6C,0x1BDEE568,0x135F20)) ... skipped
3:251  0:000      Checking volume "EFI" (PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x1,0x0,0x0)\HD(1,GPT,70B144FC-701B-45BE-91CE-26D1E706C7F8,0x800,0xC8000)) ... skipped
3:251  0:000  Custom entries finish
3:251  0:000  Scanning loaders...
3:251  0:000   0: 'Whole Disc Boot' no file system
3:251  0:000   1: 'Whole Disc Boot' no file system
3:251  0:000   2: 'EFI'
3:252  0:000      AddLoaderEntry for Volume Name=EFI
3:273  0:021   3: 'Legacy HD2' no file system
3:273  0:000   4: 'El Capitan'
3:275  0:002      AddLoaderEntry for Volume Name=El Capitan
3:277  0:002      Check if volume Is Hibernated:
3:277  0:000      Check sleep image 'by signature':
3:280  0:002      read prefs \Library\Preferences\SystemConfiguration\com.apple.PowerManagement.plist status=Success
3:280  0:000      SleepImage name from pref: ImageVolume = 'El Capitan', ImageName = '\private\var\vm\sleepimage'
3:281  0:001      sleepimage not found -> Not Found
3:281  0:000       hibernated: no - sign
3:301  0:019   5: 'Recovery HD'
3:301  0:000      AddLoaderEntry for Volume Name=Recovery HD
3:319  0:017   6: 'EFI'
3:319  0:000   7: 'Legacy HD2' no file system
3:319  0:000   8: 'Legacy HD3' no file system
3:319  0:000  Custom legacy start
3:319  0:000  Custom legacy end
3:324  0:004  GetEfiBootDeviceFromNvram: efi-boot-device-data not found
3:324  0:000  EfiBootVolume not found
3:324  0:000   found entry 0. 'Boot Microsoft EFI boot menu from EFI', Volume 'EFI', DevicePath 'PcieRoot(0x0)\Pci(0x1F,0x2)\Sata(0x0,0x0,0x0)\HD(1,GPT,38632112-1922-4A5E-81C1-BCBF7876AEBE,0x800,0xFA000)\EFI\microsoft\Boot\bootmgfw.efi'
3:324  0:000  DefaultIndex=0 and MainMenu.EntryCount=7
3:730  0:406  Found Mouse device:
3:734  0:004  GUI ready
11:986  8:251  BootOption of the entry is empty
11:986  0:000  StartLoader() start
11:986  0:000  Entry->Settings: <null string>
11:986  0:000  Finally: Bus=133799kHz CPU=1873MHz
11:986  0:000  KernelAndKextPatches copyed to started entry
11:986  0:000  Kernel and Kext Patches at DEC9A9D8:
11:986  0:000  	Allowed: y
11:986  0:000  	Debug: n
11:986  0:000  	KernelCpu: n
11:986  0:000  	Lapic: n
11:986  0:000  	Haswell-E: n
11:986  0:000  	AICPUPM: y
11:986  0:000  	AppleRTC: y
11:986  0:000  	KernelPm: y
11:986  0:000  	FakeCPUID: 0x0
11:986  0:000  	ATIController: null
11:986  0:000  	ATIDataLength: 0
11:986  0:000  	0 Kexts to load
11:986  0:000  	1 Kexts to patch
11:986  0:000  	  KextPatch[0]: 8 bytes, AppleAHCIPort
11:986  0:000  Loading boot.efi  status=Success
12:319  0:333  GetOSVersion: : 10.11.5
12:320  0:000  insert table 9 for dev 0:0
12:320  0:000  insert table 9 for dev 0:1
12:320  0:000  insert table 9 for dev 0:0
12:321  0:001  Channels: 1
12:321  0:000  Interleave: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
12:321  0:000  SMBIOS Type 17 Index = 0 => 0 0:
12:321  0:000   DIMM1 1333MHz 4096MB
12:321  0:000  SMBIOS Type 17 Index = 1 => 1 1:
12:321  0:000   DIMM2 EMPTY
12:321  0:000  SMBIOS Type 17 Index = 2 => 2 2:
12:321  0:000   DIMM3 EMPTY
12:321  0:000  SMBIOS Type 17 Index = 3 => 3 3:
12:321  0:000   DIMM4 EMPTY
12:321  0:000  mTotalSystemMemory = 4096
12:321  0:000  NumberOfMemoryDevices = 4
12:321  0:000  Type20[0]->End = 0x3FFFFF, Type17[0] = 0x1000
12:321  0:000  RSDT 0xDF770000
12:321  0:000  FADT from RSDT: 0xDF770200
12:321  0:000  XSDT 0xDF770100
12:321  0:000  FADT from XSDT: 0xDF770290
12:321  0:000  Xsdt reallocation done
12:321  0:000  old FADT length=F4
12:321  0:000  Apply DsdtFixMask=0x00008071 old way
12:321  0:000     drop _DSM mask=0x0000
12:321  0:000  ========= Auto patch DSDT Starting ========
12:322  0:000  VideoCard devID=0xDE110DE
12:322  0:000  DisplayADR1[0] = 0x30000, DisplayADR2[0] = 0x0
12:322  0:000  USBADR[0] = 0x1A0000 and PCIe = 0xFFFE
12:322  0:000  Audio HDA (addr:0x1B0000) setting specified layout-id=1 (0x1)
12:322  0:000  USBADR[1] = 0x1D0000 and PCIe = 0xFFFE
12:322  0:000  first CPU found at 2B offset 2E
12:322  0:000  score candidate at 27
12:322  0:000  score inserted in acpi_cpu_score _PR_
12:322  0:000  Found ACPI CPU: P001 And P002 And P003 And P004 And P005 And P006 And P007 And P008 And P009 And P010 And P011 And P012 And P013 And P014 And P015 And P016 
  within the score: _PR_
12:322  0:000  Found PCIROOTUID = 0
12:322  0:000  Start RTC Fix
12:322  0:000  found RTC had IRQNoFlag will move -3 bytes
12:322  0:000  ...len=94A0
12:323  0:000  new size written to 133E shift=0 len=94A0
12:323  0:000  len after correct outers 94A0
12:323  0:000  Start TMR Fix
12:323  0:000  Start PIC Fix
12:323  0:000  PIC size=2B at 129A
12:323  0:000  found PIC had IRQNoFlag will move -3 bytes
12:323  0:000  Fix Device PIC size -3
12:323  0:000  Start HPET Fix
12:323  0:000  Start LPCB Fix
12:323  0:000  found LPCB device NAME(_ADR,0x001F0000) at 10F6 And Name is SBRG
12:323  0:000  Name SBRG present at 0x10F6, renaming to LPCB
12:323  0:000  Name SBRG present at 0x1171, renaming to LPCB
12:323  0:000  Name SBRG present at 0x1188, renaming to LPCB
12:323  0:000  Name SBRG present at 0x1F8B, renaming to LPCB
12:323  0:000  Name SBRG present at 0x27FD, renaming to LPCB
12:323  0:000  Name SBRG present at 0x514B, renaming to LPCB
12:323  0:000  Name SBRG present at 0x5165, renaming to LPCB
12:323  0:000  Name SBRG present at 0x517F, renaming to LPCB
12:323  0:000  Name SBRG present at 0x5307, renaming to LPCB
12:323  0:000  Name SBRG present at 0x54AE, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6253, renaming to LPCB
12:323  0:000  Name SBRG present at 0x647D, renaming to LPCB
12:323  0:000  Name SBRG present at 0x660D, renaming to LPCB
12:323  0:000  Name SBRG present at 0x68D4, renaming to LPCB
12:323  0:000  Name SBRG present at 0x69C9, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6CD2, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6CEB, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6D03, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6D1F, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6D3A, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6D52, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6D69, renaming to LPCB
12:323  0:000  Name SBRG present at 0x6DA4, renaming to LPCB
12:323  0:000  Name SBRG present at 0x74AF, renaming to LPCB
12:323  0:000  Name SBRG present at 0x74CA, renaming to LPCB
12:323  0:000  Name SBRG present at 0x7F0F, renaming to LPCB
12:323  0:000  Name SBRG present at 0x8C03, renaming to LPCB
12:323  0:000  Name SBRG present at 0x938C, renaming to LPCB
12:323  0:000  Name SBRG present at 0x93B0, renaming to LPCB
12:323  0:000  Name SBRG present at 0x93CB, renaming to LPCB
12:323  0:000  Name SBRG present at 0x93EF, renaming to LPCB
12:323  0:000  patch HDEF in DSDT 
12:324  0:000  Start HDA Fix
12:324  0:000  Start Add Device HDEF
12:324  0:000  ========= Auto patch DSDT Finished ========
12:324  0:000  Patch table: SSDT  CpuPm
12:324  0:000   SSDT len = 0x363
12:324  0:000  Drop tables from Xsdt, SIGN=XXXX TableID= Length=0
12:324  0:000   Xsdt has tables count=7 
12:324  0:000  corrected XSDT length=92
12:324  0:000   CPUBase=1 and ApicCPUBase=1 ApicCPUNum=16
12:324  0:000  EdidDiscovered size=128
12:324  0:000  00 | 00 FF FF FF FF FF FF 00 4C 2D 57 06 33 32 48 57 
12:324  0:000  16 | 29 14 01 03 80 10 09 78 2A EE 91 A3 54 4C 99 26 
12:324  0:000  32 | 0F 50 54 23 08 00 A9 40 81 80 81 40 81 00 95 00 
12:324  0:000  48 | B3 00 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C 
12:324  0:000  64 | 45 00 A0 5A 00 00 00 1E 01 1D 00 72 51 D0 1E 20 
12:324  0:000  80 | 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 32 
12:324  0:000  96 | 3C 1B 51 11 00 0A 20 20 20 20 20 20 00 00 00 FC 
12:324  0:000  112 | 00 53 79 6E 63 4D 61 73 74 65 72 0A 20 20 01 1A 
12:324  0:000  mem_detected 1073741824
12:324  0:000  read_nVidia_ROM
12:324  0:000  Using PRAMIN fixups
12:455  0:130  patch_nvidia_rom
12:455  0:000  version 70.08.45.00.01
12:455  0:000  nVidia nVidia GeForce GT 430  1024MB NVC1 [10DE:0DE1] :: PcieRoot(0x0)\Pci(0x3,0x0)\Pci(0x0,0x0) => device #1 
12:455  0:000  Nvidia: VideoPorts: undefined, default to: 2
12:455  0:000  devprop_add_nvidia_template
12:455  0:000  default NVCAP: 04000000-00000300-0C000000-00000007-00000000
12:455  0:000  HDA Controller [8086:3B56] :: PcieRoot(0x0)\Pci(0x1B,0x0) => setting specified layout-id=1 (0x1)
12:456  0:000  LAN Controller [10EC:8168] :: PcieRoot(0x0)\Pci(0x1C,0x5)\Pci(0x0,0x0)
12:456  0:000   RCBA access disabled; trying to enable
12:456  0:000  stringlength = 2488
12:456  0:000  CurrentMode: Width=1920 Height=1080
12:456  0:000  Beginning FSInjection
FSInjectionInstall ...
- Our FSI_SIMPLE_FILE_SYSTEM_PROTOCOL installed on handle: DE87C318
FSInjectionInstall ...
- Our FSI_SIMPLE_FILE_SYSTEM_PROTOCOL installed on handle: DE87C318
12:457  0:000  ** Warning: Your MLB is not suitable for iMessage(must be 17 chars long) !
12:457  0:000  Preparing kexts injection for arch=x86_64 from EFI\CLOVER\kexts\Other
12:458  0:000  Preparing kexts injection for arch=x86_64 from EFI\CLOVER\kexts\10.11
12:458  0:000    Extra kext: EFI\CLOVER\kexts\10.11\FakeSMC.kext
12:461  0:003    Extra kext: EFI\CLOVER\kexts\10.11\RealtekRTL8111.kext
12:470  0:008  Removed efi-boot-device-data variable: Not Found
12:470  0:000  Custom boot is disabled
12:470  0:000  Closing log

Thanks.

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...