Derty Posted July 23, 2011 Share Posted July 23, 2011 lo encontre en un post ruso hace unos días. esta bien saberlo. Standard CMOS Features: Date: [set] Time: [set] Drive A: [None] Floppy 3 Mode Support: [Disabled] Halt On: [No Errors] Advanced BIOS Features: Hard Disk boot Priority: [set your boot drive as #1] First Boot Device: [Hard Disk] Second Boot Device: [CDROM] Third Boot Device: [Disabled] Boot Up Floppy Seek: [Disabled] Boot Up Num-Lock: [On] Password Check: [setup if desired] HDD S.M.A.R.T. Capability: [Enabled] Limit CPUID Max. to 3: [Disabled] No-Execute Memory Protect: [Enabled] Delay for HDD (Secs): [0] Full Screen LOGO Show: [Disabled] Init Display First: [PEG] Integrated Peripherals: SATA RAID/AHCI Mode: [AHCI] SATA Port0-3 Native mode: [Enabled] USB Controller: [Enabled] USB 2.0 Controller: [Enabled] USB Keyboard Function: [Enabled] USB Mouse Function: [Enabled] USB Storage Function: [Enabled] Azalia Codec: [Enabled] * Disable this if you are using a separate sound card Onboard H/W 1394: [Enabled] Onboard H/W LAN1: [Enabled] * Disable this if you are using a separate network card Onboard H/W LAN2: [Disabled] * You can enable this if you want to use both NICs Green LAN: [Disabled] SMART LAN1: [Press Enter] SMART LAN2: [Press Enter] Onboard LAN1 Boot ROM: [Disabled] Onboard LAN2 Boot ROM: [Disabled] Onboard SATA/IDE Device: [Enabled] Onboard SATA/IDE Ctrl Mode: [AHCI] Smart Backup: [Disabled] Power Management Setup: ACPI Suspend Type: [s3(STR)] USB Device Wake-Up From S3: [Enabled] Soft-Off by PWR-BTTN: [instant-Off] PME Event Wake Up: [Disabled] Power On by Ring: [Disabled] Resume by Alarm: [Disabled] HPET Support: [Enabled] HPET Mode: [64-bit mode] Power On By Mouse: [Disabled] Power On By Keyboard: [Disabled] AC Back Function: [soft-Off] Link to comment Share on other sites More sharing options...
jpa Posted July 23, 2011 Share Posted July 23, 2011 yo tengo este 1. Start by using Load Optimized Defaults. 2. In M.I.T. Advanced Memory Settings: Exteme Memory Profile(X.M.P.) -> Profile1 Performance Enhance -> Standard 3. In M.I.T. Advanced Frequency Settings: Under Advanced CPU Core Features: Intel® Turbo Boot Tech. -> Enabled CPU Enhanced Halt (C1E) -> Enabled C3/C6/C7 State Support -> Enabled CPU Thermal Monitor -> Enabled CPU EIST Function -> Enabled Bi-Directional PROCHOT -> Enabled 4. In Integrated Peripherals ICH SATA Control Mode -> AHCI SATA Port0-3 Native Mode -> Enabled eSATA Ctrl Mode -> AHCI GSATA 6_7/IDE Ctrl Mode -> AHCI GSATA 8_9/IDE Ctrl Mode -> AHCI 5. In Power Management: HPET Mode -> 64-bit mode 6. In Advanced BIOS Features: Quick Boot -> Enabled Third Boot Device Floppy -> Disabled HDD S.M.A.R.T. Capability -> Enabled Full Screen LOGO Show -> Disabled Init Display First PCI -> PCIE x16-1 7. In Integrated Peripherals: GSATA 6_7/IDE Controller -> Disabled GSATA 8_9/IDE Controller -> Disabled 8. In Power Management: Soft-Off by PWR-BTTN -> Delay 4 Sec. 9. In PC Health Status: CPU Warning Temperature -> 60C/140F CPU FAN Fail Warning -> Enabled Link to comment Share on other sites More sharing options...
Recommended Posts