Jump to content

Mac OS X Lion (Developer Preview) Released

harrydeo

By harrydeo,
in New Releases and Updates

 Share
1,521 posts in this topic

Recommended Posts

old_eye
old_eye
Posted
Posted
Is DP 4 (as DP3) as an Update by Sotwareupate (Lion DP3 running) available or only as an full install ?

Yesterday night i tried SW Up but said "No updates available" running DP3.

Being no developer I experienced the same - no luck via software update - that was only possible for me with dp2.

Took the "stormy" way - 3.72 dmg.

Link to comment
Share on other sites
Duque
Duque
Posted
Posted

no softwareupdate ... so you have to install again by using/clone the BaseSystem partition ... and copy packages etc. ...

 

but while installing DP4, you have the choice to install/update to your old Lion Preview, keeping all your programs and settings ... works fine ...

 

Tip: Chameleon did not work with BaseSystem for me ... I used XPC (usb stick) to install ... after install, Chameleon-Lion did boot without any issues ... and one more thing ... do not forget to copy the mach_kernel from InstallESD to your new BaseSystem ... :D

Link to comment
Share on other sites
mitch_de
mitch_de
Posted
Posted

OK, but more work for me, because i am MBR type user. So i had to install it by XPC USB Stick on second USB Stick GPT Type formatted and after that clone to my MBR Lion volume.

Link to comment
Share on other sites
athena
athena
Posted
Posted
Yes, i did it via a clone installation.. works good.. but screen brightness is very low, even if i turn it up it dosent do much change.

 

Booting verbose, i can see that it happends somewhere in between fakesmc and a error message about being unable to generate c-states...

 

 

Sorry, what do you mean a clone installation? I have Lion DP3 installed, what do I do from there?

Link to comment
Share on other sites
nandor690
nandor690
Posted
Posted
OK, but more work for me, because i am MBR type user. So i had to install it by XPC USB Stick on second USB Stick GPT Type formatted and after that clone to my MBR Lion volume.

 

I don't understand why no one is using the latest [url="http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/"]#####[/url], works for both lion and snow leopard!!!!

 

 

Being no developer I experienced the same - no luck via software update - that was only possible for me with dp2.

Took the "stormy" way - 3.72 dmg.

 

 

 

Boy! You guys are making this out to be way harder than it actually is!

Link to comment
Share on other sites
fantomas
fantomas
Posted
Posted

New build , 11A480b !!! New wallpaper too !!! :)

 

Capture_d___e__cran_2011_06_08_a___11.23.04.png Capture_d_____cran_2011_06_08____12.13.17.png

 

 

AppleRTL8139Ethernet.kext missing from IONetworkingFamily.kext

 

 

Install is done like DP1, no need patching OSInstall.mpkg ! I restored BaseSystem.dmg on my usb stick ( 16go ) ,

 

copied Packages folder and mach_kernel ( error message on start " no found mach_kernel ) that are in DP4 !

 

then I installed chameleon R750 and copied my Extra folder and that's all !! :)

Link to comment
Share on other sites
mitch_de
mitch_de
Posted
Posted

Ok, i tried same methode (has success with DP1...3).

But always blocked by "not installable on this computer", after language selection.

I removed all occurences of the PlatformSupport.plist, what worked to install DP1...3 but also "not installable"?

 

Any hints?

Link to comment
Share on other sites
fantomas
fantomas
Posted
Posted

Once BaseSystem.dmg restored on my USB stick, there was no PlatformSupport.plist in Volume/my usb stick/S/B/CoreServices

 

capturedcran20110608143.png

 

 

PlatformSupport.plist is found only in S/B/CoreServices of DP4.dmg

Link to comment
Share on other sites
Duque
Duque
Posted
Posted
Ok, i tried same methode (has success with DP1...3).

But always blocked by "not installable on this computer", after language selection.

I removed all occurences of the PlatformSupport.plist, what worked to install DP1...3 but also "not installable"?

 

Any hints?

 

 

MBR ? Use patched OSInstall ...

OSInstall.mpkg.zip

Link to comment
Share on other sites
Zprood
Zprood
Posted
Posted
Does DP4 have any new 64-bit GMAX3100 video kexts?

No, since Apple gives up 64bit support of this graphics, it only can work in the 32bit. So do not to expect that news.BTW I have installed DP4, and no 64-bit drivers.

 

Another one, does anyone have USB mouse problem? I get the boring stuff right now, can't control the mouse well, when move it a little quick, it jumps. I doubt that it is that graphics drivers bug ?

Link to comment
Share on other sites
mitch_de
mitch_de
Posted
Posted
For MBR you also need patched OSInstall binary

http://blog.nawcom.com/?p=751

YEP, the old way in the .mpkg edit didnt work anymore.

 

I also found out , that in OSInstall.mpgk other things changed between DP3 and DP4!

 

It seems that some part of the hardware features / board id check may fail (not installable) on some CPU / system type like my C2D E7300 CPU.

 

 

It seems that now not only in the SupportedPlatform.plist (we remove) the list is fixed , also in the .mpkg!

 

function is64bit() {
   var is64bit =system.sysctl('hw.cpu64bit_capable');
return is64bit;
}

function isVirtualMachine(){

var cpuFeatures = system.sysctl( 'machdep.cpu.features' );
		cpuFeatures=cpuFeatures.split(" ");
		for( var i = 0; i < cpuFeatures.length; i++ ){
		 	if( cpuFeatures[i] == "VMM" ){
					return true;
		  	}	
		}
		return false;			

}

function isSupportedPlatform(){

if( isVirtualMachine() ){
	return true;
}

var platformSupportValues=["Mac-F2268DC8","Mac-F22C86C8","Mac-F22587C8","Mac-F2218FA9","Mac-F2218EA9","Mac-F42D86A9","Mac-F22C8AC8","Mac-F22586C8","Mac-942B59F58194171B","Mac-F226BEC8",
"Mac-F4218FC8","Mac-942459F5819B171B","Mac-7BA5B2794B2CDB12","Mac-F4218EC8","Mac-F2208EC8","Mac-F22C89C8","Mac-F22587A1","Mac-F221DCC8","Mac-F42388C8","Mac-F223BEC8","Mac-F4238CC8","Mac-F222BEC8",
"Mac-F227BEC8","Mac-F4208AC8","Mac-F22788A9","Mac-F4238BC8","Mac-F221BEC8","Mac-C08A6BB70A942AC2","Mac-8ED6AF5B48C039E1","Mac-F2238AC8","Mac-F4208EAA","Mac-F22788C8","Mac-F2268EC8",
"Mac-F2218EC8","Mac-F22589C8","Mac-F4228EC8","Mac-F22788AA","Mac-F42C86C8", "Mac-F4208CA9","Mac-942C5DF58193131B","Mac-F2238BAE","Mac-F42289C8","Mac-F2268CC8",
"Mac-F4208DC8","Mac-F2218FC8"," Mac-742912EFDBEE19B3","Mac-F4208DA9","Mac-F42D89C8","Mac-F4208CAA","Mac-F42D89A9","Mac-F2268AC8","Mac-F42C89C8","Mac-942452F5819B1C1B"
,"Mac-F42786A9","Mac-F42D88C8","Mac-F42187C8",
"Mac-94245B3640C91C81","Mac-F42D86C8","Mac-4BC72D62AD45599E","Mac-F2268DAE","Mac-F42C8CC8","Mac-F42C88C8","Mac-94245A3940C91C80","Mac-F42386C8","Mac-942B5BF58194151B","Mac-F42189C8"];
var boardID = system.ioregistry.fromPath('IOService:/')['board-id'];

if( !boardID || platformSupportValues.length ==0 ) {
	return false
}
for( var i = 0; i < platformSupportValues.length; i++ ){
 	if( boardID == platformSupportValues[i] ){
			return true;
  	}	
}

return false;
}

function installCheckScript(){

		try{
			var machineType = system.ioregistry.fromPath('IODeviceTree:/')['compatible'];

			if (typeof(isFNI) == "undefined" && typeof(hwbeInstallCheck) != "undefined") {
				if (!hwbeInstallCheck()) {
					return false;
				}
			} 

			if(!hasAtLeastRam(minRam)){
				my.result.message = system.localizedStringWithFormat('IC_RAM_message');
				my.result.type = 'Fatal';
				return false;
			}

			if(!is64bit()){
				my.result.message = system.localizedStringWithFormat('IC_Unsupported_Processor');
				my.result.type = 'Fatal';
				return false;
			}

			if (system.compareVersions(system.version.ProductVersion, '10.7') < 0 && system.env.COMMAND_LINE_INSTALL) {
				my.result.message = system.localizedStringWithFormat('IC_Command_Line_message', '10.7');
				my.result.type = 'Fatal';
				return false;
			}

			if(!isSupportedPlatform()){
				my.result.message = system.localizedStringWithFormat('IC_Unsupported_Platform');
				my.result.type = 'Fatal';
				return false;
			}


			if (typeof(findBJPrinters) != "undefined") findBJPrinters();

		} catch (e) {
			system.log('installCheckScript threw exception ' + e);
		}

		return true;
}

 

Attached: OSInstall.mpgk patched for an install without any of HW check and Board-ID (Mac-...) .

Also added, for information of the install process my install.log - WAS now with sucess after using my modded .mpkg.

OSInstall.mpkg.zip

Installationsprotokoll_8_Jun_2011.txt.zip

Link to comment
Share on other sites
me@home
me@home
Posted
Posted
OSInstall.mpgk patched for an install without any of HW check and Board-ID (Mac-...) ....

 

Thank you !!

 

Now I have running DP4 without issues, OK I had to replace AppleHDA+IOnetworking but that's been always since 10.7.

 

post-55980-1307561345_thumb.png

Link to comment
Share on other sites
mitch_de
mitch_de
Posted
Posted

Little Problem: I get very early in the boot process an "ACPI not 2.0 - Press any key to boot" (using -v, not excat but similar.

After pressing an key the DP4 boots + run normaly.

Never had that before. Some Chameleon or BIOS/DSDT problem?

Link to comment
Share on other sites
fantomas
fantomas
Posted
Posted
Little Problem: I get very early in the boot process an "ACPI not 2.0 - Press any key to boot" (using -v, not excat but similar.

After pressing an key the DP4 boots + run normaly.

Never had that before. Some Chameleon or BIOS/DSDT problem?

 

 

me too !! i think this is because of the latest version of chameleon , r994 !!! before installing this version, no problem !!! ;)

Link to comment
Share on other sites
Flashe
Flashe
Posted
Posted

Hi,

 

After installation of DP4 are the same error messages with the other DP.

 

My kernel.log

 

Jun  9 00:07:50 localhost kernel[0]: zone leak detection enabled
Jun  9 00:07:50 localhost kernel[0]: standard timeslicing quantum is 10000 us
Jun  9 00:07:50 localhost kernel[0]: mig_table_max_displ = 72
Jun  9 00:07:50 localhost kernel[0]: AppleACPICPU: ProcessorId=1 LocalApicId=0 Enabled
Jun  9 00:07:50 localhost kernel[0]: AppleACPICPU: ProcessorId=2 LocalApicId=1 Enabled
Jun  9 00:07:50 localhost kernel[0]: AppleACPICPU: ProcessorId=3 LocalApicId=130 Disabled
Jun  9 00:07:50 localhost kernel[0]: AppleACPICPU: ProcessorId=4 LocalApicId=131 Disabled
Jun  9 00:07:50 localhost kernel[0]: calling mpo_policy_init for Sandbox
Jun  9 00:07:50 localhost kernel[0]: Security policy loaded: Seatbelt sandbox policy (Sandbox)
Jun  9 00:07:50 localhost kernel[0]: calling mpo_policy_init for Quarantine
Jun  9 00:07:50 localhost kernel[0]: Security policy loaded: Quarantine policy (Quarantine)
Jun  9 00:07:50 localhost kernel[0]: calling mpo_policy_init for TMSafetyNet
Jun  9 00:07:50 localhost kernel[0]: Security policy loaded: Safety net for Time Machine (TMSafetyNet)
Jun  9 00:07:50 localhost kernel[0]: Copyright © 1982, 1986, 1989, 1991, 1993
Jun  9 00:07:50 localhost kernel[0]: The Regents of the University of California. All rights reserved.
Jun  9 00:07:50 localhost kernel[0]: MAC Framework successfully initialized
Jun  9 00:07:50 localhost kernel[0]: using 16384 buffer headers and 10240 cluster IO buffer headers
Jun  9 00:07:50 localhost kernel[0]: IOAPIC: Version 0x20 Vectors 64:87
Jun  9 00:07:50 localhost kernel[0]: ACPI: System State [s0 S3 S4 S5] (S3)
Jun  9 00:07:50 localhost kernel[0]: PFM64 0xf10000000, 0xf0000000
Jun  9 00:07:50 localhost kernel[0]: [ PCI configuration begin ]
Jun  9 00:07:50 localhost kernel[0]: PCI configuration changed (bridge=2 device=1 cardbus=0)
Jun  9 00:07:50 localhost kernel[0]: [ PCI configuration end, bridges 6 devices 19 ]
Jun  9 00:07:50 localhost kernel[0]: RTC: Only single RAM bank (128 bytes)
Jun  9 00:07:50 localhost kernel[0]: FakeSMC: Opensource SMC device emulator by netkas © 2009
Jun  9 00:07:50 localhost kernel[0]: FakeSMC: Monitoring plugins support by mozodojo © 2010
Jun  9 00:07:50 localhost kernel[0]: FakeSMC: Original idea of plugins and code sample by usr-sse2 © 2010
Jun  9 00:07:50 localhost kernel[0]: AppleIntelCPUPowerManagement: (built 19:51:42 May 29 2011) initialization complete
Jun  9 00:07:50 localhost kernel[0]: mbinit: done [64 MB total pool size, (42/21) split]
Jun  9 00:07:50 localhost kernel[0]: Pthread support ABORTS when sync kernel primitives misused
Jun  9 00:07:50 localhost kernel[0]: com.apple.AppleFSCompressionTypeDataless kmod start
Jun  9 00:07:50 localhost kernel[0]: Vendor ID 50505050 50505050
Jun  9 00:07:50 localhost kernel[0]: Device ID 50505050 50505050
Jun  9 00:07:50 localhost kernel[0]: 50505050505050505050505050505050
Jun  9 00:07:50 localhost kernel[0]: PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP
Jun  9 00:07:50 localhost kernel[0]: FireWire runtime power conservation disabled. (2)
Jun  9 00:07:50 localhost kernel[0]: com.apple.AppleFSCompressionTypeZlib kmod start
Jun  9 00:07:50 localhost kernel[0]: JMicronATA: JMB363 (CMD 0xdc00, CTR 0xd880, IRQ 16, BM 0xd400)
Jun  9 00:07:50 localhost kernel[0]: com.apple.AppleFSCompressionTypeDataless load succeeded
Jun  9 00:07:50 localhost kernel[0]: com.apple.AppleFSCompressionTypeZlib load succeeded
Jun  9 00:07:50 localhost kernel[0]: AppleIntelCPUPowerManagementClient: ready
Jun  9 00:07:50 localhost kernel[0]: FireWire (OHCI) Lucent ID 5811 PCI now active, GUID 0011d80001637997; max speed s400.
Jun  9 00:07:50 localhost kernel[0]: ATAPI Device checked
Jun  9 00:07:50 localhost kernel[0]: JMicronATA: JMB363 (CMD 0xd800, CTR 0xd480, IRQ 16, BM 0xd408)
Jun  9 00:07:50 localhost kernel[0]: USBMSC Identifier (non-unique): 000000009833 0x5e3 0x716 0x9727
Jun  9 00:07:50 localhost kernel[0]: From path: "uuid", 
Jun  9 00:07:50 localhost kernel[0]: Waiting for boot volume with UUID FE14B25B-3802-31A8-A88D-936AAA57D8F0
Jun  9 00:07:50 localhost kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
Jun  9 00:07:50 localhost kernel[0]: Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleAHCI/PRT0@0/IOAHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice/IOBlockStorageDriver/SAMSUNG HM160HI Media/IOGUIDPartitionScheme/Mac OS X Lion 10.7@2
Jun  9 00:07:50 localhost kernel[0]: BSD root: disk0s2, major 14, minor 2
Jun  9 00:07:50 localhost kernel[0]: jnl: unknown-dev: replay_journal: from: 3720192 to: 8075776 (joffset 0x258000)
Jun  9 00:07:50 localhost kernel[0]: jnl: unknown-dev: journal replay done.
Jun  9 00:07:50 localhost kernel[0]: Kernel is LP64
Jun  9 00:07:50 localhost kernel[0]: AppleYukon2: Marvell Yukon Gigabit Adapter 88E8056 Singleport Copper SA
Jun  9 00:07:50 localhost kernel[0]: AppleYukon2: RxRingSize <= 1024, TxRingSize 256, RX_MAX_LE 1024, TX_MAX_LE 768, ST_MAX_LE 3328
Jun  9 00:07:50 localhost kernel[0]: hfs: Removed 8 orphaned / unlinked files and 33 directories 
Jun  9 00:07:51 localhost kernel[0]: yukon: Ethernet address 00:1b:fc:e1:74:95
Jun  9 00:07:51 localhost kernel[0]: AppleRTL8169Ethernet: Ethernet address 00:1b:fc:e1:66:42
Jun  9 00:07:56 localhost kernel[0]: Waiting for DSMOS...
Jun  9 00:07:56 localhost kernel[0]: macx_swapon SUCCESS
Jun  9 00:07:58 localhost kernel[0]: NVDANV50HAL loaded and registered.
Jun  9 00:07:58 localhost kernel[0]: VoodooPS2SynapticsTouchPad loaded
Jun  9 00:07:59 localhost kernel[0]: Sound assertion "false == codecFound" failed in AppleHDADriver at line 1449 goto handler
Jun  9 00:07:59 localhost kernel[0]: Sound assertion "0 == pathMap_aDriverInstance" failed in AppleHDADriver at line 2037 goto Exit
Jun  9 00:07:59 localhost kernel[0]: Sound assertion "0 != createAudioEngines ( fPathMap_aDriverInstance )" failed in AppleHDADriver at line 207 goto Exit
Jun  9 00:07:59 localhost kernel[0]: Sound assertion "false == me->completeStart ()" failed in AppleHDADriver at line 996 goto Exit
Jun  9 00:07:59 localhost kernel[0]: No interval found for . Using 8000000
Jun  9 00:07:59 localhost kernel[0]: ApplePS2Trackpad: ALPS GlidePoint v0.0
Jun  9 00:07:59 localhost kernel[0]: IntelThermal: CPU family 0x6, model 0x17, stepping 0xa
Jun  9 00:07:59 localhost kernel[0]: IntelThermal: Found 2 cores 0 threads
Jun  9 00:07:59 localhost kernel[0]: IntelThermal: CPU Tjmax 100
Jun  9 00:07:59 localhost kernel[0]: SuperIO: Probing NSC
Jun  9 00:07:59 localhost kernel[0]: SuperIO: Probing ITE
Jun  9 00:07:59 localhost kernel[0]: SuperIO: Probing Fintek
Jun  9 00:07:59 localhost kernel[0]: SuperIO: Fintek: Found unsupported chip ID=0xa0 REVISION=0x23
Jun  9 00:07:59 localhost kernel[0]: SuperIO: Probing SMSC
Jun  9 00:07:59 localhost kernel[0]: SuperIO: Probing Winbond
Jun  9 00:08:00 localhost kernel[0]: SuperIO: Detected Winbond W83627DHG on 0x290
Jun  9 00:08:00 localhost kernel[0]: DSMOS has arrived
Jun  9 00:08:00 localhost kernel[0]: PTKawainVi: started
Jun  9 00:08:00 localhost kernel[0]: Vendor ID: 10de, Device ID: 622
Jun  9 00:08:00 localhost kernel[0]: Architecture: 200000
Jun  9 00:08:00 localhost kernel[0]: G94 [GeForce 9600 GT]
Jun  9 00:08:00 localhost kernel[0]: BIOS successfully read
Jun  9 00:08:00 localhost kernel[0]: SuperIO: Binding key TN0P
Jun  9 00:08:00 localhost kernel[0]: SuperIO: Binding key VC0C
Jun  9 00:08:00 localhost kernel[0]: SuperIO: Fan 0 name is associated with hardware Fan1
Jun  9 00:08:00 localhost kernel[0]: SuperIO: Binding key F0Ac
Jun  9 00:08:00 localhost kernel[0]: SuperIO: Fan 1 name is associated with hardware Fan2
Jun  9 00:08:00 localhost kernel[0]: SuperIO: Binding key F1Ac
Jun  9 00:08:03 localhost kernel[0]: jnl: disk0s3: replay_journal: from: 7335424 to: 145408 (joffset 0xe6000)
Jun  9 00:08:03 [0]: jnl: disk0s3: 2: extra replay stopped @ 145408 / 0x23800 (seq 16258717 < 16258852)
Jun  9 00:08:05 [0]: jnl: disk0s3: journal replay done.
Jun  9 00:08:06 [0]: jnl: disk0s4: replay_journal: from: 3195392 to: 3643392 (joffset 0x16d000)
Jun  9 00:08:07 [0]: nstat_lookup_entry failed: 2

 

 

 

RTC: Only single RAM bank (128 bytes),why ?

 

Thanks.

Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...