Jump to content

DSDT Auto-Patcher

MaLd0n

By MaLd0n,
in Patches

 Share
5,753 posts in this topic

Recommended Posts

webkostas
webkostas
Posted
Posted
dsdt.unimatrix725.zip

 

send me DSDT again

run on terminal

perl -e 'open(CMD, "ioreg -lw0 \| grep DSDT|") or die; while(<CMD>) { chomp; if($_ =~ /\"DSDT\.?\d?\"=<([^>]*)>/) { $buff = $1; open(PIP, "|xxd -r -p > ~/Desktop/dsdt.aml") or die; print PIP "$1"; } }'

DSDT generate in desktop

I'll try the last shot in the dark post-557433-1312229501.gif

 

Yes sir! :D Here is my DSDT as you asked for. total faith in your powers ;)

webkostas.dsdt.aml.zip

Link to comment
Share on other sites
webkostas
webkostas
Posted
Posted
NativePM ok

USB is Built in?

 

Just tried with the new dsdt but no luck :unsure: same thing, computer does not wake up after normal sleep. Should I use with sleep mode 3 (currently I'm using "0") or it does not matter?

 

USB is Built in?

 

What exactly do you mean? Never had any problems with USB actually.

Link to comment
Share on other sites
MaLd0n
MaLd0n
Posted
  • Author
Posted
Hi Mald0n!

Do you mind taking a glimpse to this dsdt from an asus p5vd2-vm?

http://dl.dropbox.com/u/363153/p5vd2-vm_dsdt.dsl

Its not listed in your dsdt patcher.

Thanks in advance mate.

dsdt.anibalin.zip

\õ/

VIA?

_DD.gif

 

hi MaLd0n

 

I'm here to ask help from you.

you're so kind to help me with the dsdt of my P5Q?

I am attaching all

dsdt__hdef.zip

I know which kexts are concerned too much and put the string in the attachment HDEF dsdt thanks a lot

Asus P5Q mobo smooth

Thx

dsdt.Tristano.zip

remove EvOreboot, NullCPUPowerManagement

add in boot.plist

<key>GeneratePStates</key>
<string>Yes</string>
<key>GenerateCStates</key>
<string>Yes</string>

 

What exactly do you mean? Never had any problems with USB actually.

look at the AboutThisMac/More Info/USB

Link to comment
Share on other sites
webkostas
webkostas
Posted
Posted
look at the AboutThisMac/More Info/USB

 

yep!

 

USB Bus:

 

Host Controller Location: Built-in USB

Host Controller Driver: AppleUSBUHCI

PCI Device ID: 0x2832

PCI Revision ID: 0x0003

PCI Vendor ID: 0x8086

Bus Number: 0x5d

 

BCM92045NMD:

 

Product ID: 0x2101

Vendor ID: 0x0a5c (Broadcom Corp.)

Version: 3.54

Serial Number: 00242CDC0DA9

Speed: Up to 12 Mb/sec

Manufacturer: Broadcom Corp

Location ID: 0x5d200000 / 2

Current Available (mA): 500

Current Required (mA): 0

Link to comment
Share on other sites
niraj
niraj
Posted
Posted
Hay hi

I have Installed mac osx 10.6.8 (Hazard Edition), i got every thing working very properly, only that after 30-50 mins or may be some times on Sterting Mac i get Kernel Panic, also sometimes i get kernel panic while running firefox, and safari

 

So please solve the problem.

 

Can you please make me a DSDT Patch and also how to install a patch

 

my configuration are as follows

 

Motherboard : DH61WW

Processor : Intel i3 (2100) 3.1GHZ Sandy Bridge

RAM : 4 GB DDR3 Ram

Graphics : Sparkle Nvidia 8400 GS

Audio : ALC 892 Audio Codec

Lan : Intel® 82579V Gigabit

Legacy I/O : Nuvoton* W83677HG-i I/O controller for hardware management and serial port, parallel port, and PS/2 support

 

Please create me a patch, mostly after 30-50 Mins after or sometimes on starting up of mac i am getting Kernel Panic,

also the audio is working good but still in getting noise, so please let me know how to solve the problem.

I am sending you my Bios file please let me know if you need any other files

BEH6110H.86A.0023.BI.ZIP

 

 

Hay any one can please, provide me the DSDT patch for this motherboard

Please reply

Link to comment
Share on other sites
xxmacmanxx
xxmacmanxx
Posted
Posted
if you do not want to try

I can not help you

sorry

 

 

 

Hey Mald0n! :)

 

First of all, ok, I'm willing to do everything now, you are the boss! :)

 

So, I finally deleted the NullCPUPowermanagment.kext, but unfortunately, I receive the KP at "AppleIntelCPUPM.kext".

 

What am I expected to do know? My kextstat is in the last post if you need it.

 

 

Thanks!

xxmacmanxx

Link to comment
Share on other sites
yout
yout
Posted
Posted

Hey Mald0n!

 

Two things:

 

1. Would you have the auto sleep fix for a Gigabyte Z68-UD5-B3 (F7) motherboard?. I can force system to sleep and wake without issues but wont auto sleep. I don't have a CD-ROM or equiv connected not using USB3.0 drivers.

 

2. Any workaround/fix for facetime running on sandy bridge processors?. Chameleon 755 is not supported on these processors which appears to be the only working solution out there.

 

Thxs

 

MOBO: GB Z68-UD5-B3, F7

MEM: 16GB 1600Mhz

HD: Crucial 128GB SSD3

OS: LION, 10.7

Link to comment
Share on other sites
omniatlas
omniatlas
Posted
Posted

Hi Maldon, well I bit the dust and went AMD -- Intel chips were too expensive, and when I can get a Phenom II 955 Quad Core 3.2 ghz (overclocked to 3.7 ghz, but others have clocked it to 7.1 ghz!) for $100 why should I spend more than double the price with the intel equivalent?

 

Unfortunately Hackintosh is not really good for AMD chips and I'm even having trouble installing Mac OS Lion (keeps on rebooting). Hopefully you can be my savior and help me get a working DSDT file so I can get an Install screen.

 

My specs --

 

Motherboard: Gigabyte M68MT-S2P

Memory: DDR3 4096 MBytes, Channel # Single

 

Do I need to provide more information, or is there a program I can use to send you all my specs? I would really appreciate it so we can start building an AMD compatible motherboard list for your DSDT Autopatcher.

 

Thanks!

Link to comment
Share on other sites
iMickk
iMickk
Posted
Posted
Unfortunately Hackintosh is not really good for AMD chips and I'm even having trouble installing Mac OS Lion (keeps on rebooting). Hopefully you can be my savior and help me get a working DSDT file so I can get an Install screen.

Damm, you bought an AMD processor for Hackintosh?

You need to wait on a Legacy Kernel.. There is no support for AMD in the Vanilla Lion kernel. So it reboots automatically. Check blog.nawcom.com :P.

Link to comment
Share on other sites
omniatlas
omniatlas
Posted
Posted
Damm, you bought an AMD processor for Hackintosh?

You need to wait on a Legacy Kernel.. There is no support for AMD in the Vanilla Lion kernel. So it reboots automatically. Check blog.nawcom.com ;).

 

whoops, I must have replaced mach_kernel with legacy_kernel for OSX 10.6.8, nowonder its not working!

 

Nawcom is away on leave, indefinitely :P Anyone else working on the project? The man was a genius.

Link to comment
Share on other sites
xian1243
xian1243
Posted
Posted

Hey Mald0n...

 

I've been trying for 2 weeks to get my DSDT patched for CMOS reset fix, OS Emu, HPET fix, sleep/shutdown and also to no avail to get my ALC889 audio working...

 

I've tried [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url], with DSDT, with HDAEnabler, I've also tried VoodooHDA (with removed HDAEnablers and AppleHDA of course) and nothing works. I can't get more than a simple Intel Audio with ID 889 in system profiler, and while using DSDT patches I get nothing. I also tried bin patched AppleHDA.kexts from 10.6.3, 4, 5, 6, 7 and 10.6.8.

 

I've tried at least 7 different DSDT patches, and I still haven't found a solution.

 

My motherboard is an AMD Gigabyte board (GA-790FXTA-UD5) and is revision 1.0.

 

Processor: AMD Phenom II x2 545 -> working

6 GB DDR3 @ 1333 MHz: Corsair and G.Skill -> only 4GB working with legacy_kernel for 32 bit apps

South Bridge: SB750 (6 SATA II ports, 1 PATA channel) -> working

North bridge: 790FX (PCI-E 2.0 x16) -> using ATI HD 6870 with non-functional HDMI audio

Audio chipset: ALC889 (with Dolby HD) -> not working

Ethernet : 2x Realtek 8111D -> working

eSATA: JMicron 3683 -> working

USB 3.0: Reneses -> working

SATA 3.0: Marvell SE9128 (2 SATA III ports) -> working

1394a (firewire): built-in -> working

 

Audio has : 6 ports and supports 7.1 audio (with mic-in, line-in, and 4 stereo outputs)

 

Everything works except for CMOS reset, other necessary fixes, sleep, shutdown, restart, and most of all... audio (nor ALC889 nor HDMI).

 

If you could help me out that would be great! Thanks :)

 

I've uploaded a clean DSDT from the latest beta bios I'm using (F3J) and using your tool!

 

-xian1243

send_me.zip

Link to comment
Share on other sites
pred8er
pred8er
Posted
Posted

Hello!

I have a ZOTAC ND22, Link to ZOTAC Hompage

this is a nice little barebone with a celereon SU2300 1,2ghz, 4GB RAM. I replaced the WiFi card with a Broadcom (works out of the box).

 

I tried a lot but sleep, shutdown, restart don't work. Now I did a clean new SL install with [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url], so far no [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url] I still boot with [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url].

 

There is already a thread about the barebone, unfortunately the dsdt doesn't work

http://www.insanelymac.com/forum/index.php?showtopic=237091

 

 

send_me.zip

 

I would much appreciate, if you could support the ZOTAC ND22 and create a dsdt

 

Best regards

Tom

Link to comment
Share on other sites
MaLd0n
MaLd0n
Posted
  • Author
Posted
Hay any one can please, provide me the DSDT patch for this motherboard

Please reply

I do not want the bios

I just want the files and the DSDT

send me files

http://www.insanelymac.com/forum/index.php...st&id=81816

 

Hey Mald0n! :)

 

First of all, ok, I'm willing to do everything now, you are the boss! :)

 

So, I finally deleted the NullCPUPowermanagment.kext, but unfortunately, I receive the KP at "AppleIntelCPUPM.kext".

 

What am I expected to do know? My kextstat is in the last post if you need it.

 

 

Thanks!

xxmacmanxx

HPET enable in bios setup?

do you need a...

http://www.insanelymac.com/forum/index.php?showtopic=258611

 

Hey Mald0n!

 

Two things:

 

1. Would you have the auto sleep fix for a Gigabyte Z68-UD5-B3 (F7) motherboard?. I can force system to sleep and wake without issues but wont auto sleep. I don't have a CD-ROM or equiv connected not using USB3.0 drivers.

 

2. Any workaround/fix for facetime running on sandy bridge processors?. Chameleon 755 is not supported on these processors which appears to be the only working solution out there.

 

Thxs

 

MOBO: GB Z68-UD5-B3, F7

MEM: 16GB 1600Mhz

HD: Crucial 128GB SSD3

OS: LION, 10.7

http://www.insanelymac.com/forum/index.php?showtopic=182535

 

I have an MSI Eclipse x58. Will the MSI x58m options work for that?

Nope

send me files

http://www.insanelymac.com/forum/index.php...st&id=81816

Link to comment
Share on other sites
xxmacmanxx
xxmacmanxx
Posted
Posted

Hi Mald0n!

 

Yes, HPET is enabled in BIOS, I checked it.

 

About the speed stepper, I'm not sure if it's made for every board , because in the first line of the thread it says:

 

SpeedStepper is a command-line tool that patches AppleIntelCPUPowerManagement.kext to load on ASUS P67 boards.

 

Do you think it's working for me?

Link to comment
Share on other sites
MaLd0n
MaLd0n
Posted
  • Author
Posted
Hey Mald0n...

 

I've been trying for 2 weeks to get my DSDT patched for CMOS reset fix, OS Emu, HPET fix, sleep/shutdown and also to no avail to get my ALC889 audio working...

 

I've tried [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url], with DSDT, with HDAEnabler, I've also tried VoodooHDA (with removed HDAEnablers and AppleHDA of course) and nothing works. I can't get more than a simple Intel Audio with ID 889 in system profiler, and while using DSDT patches I get nothing. I also tried bin patched AppleHDA.kexts from 10.6.3, 4, 5, 6, 7 and 10.6.8.

 

I've tried at least 7 different DSDT patches, and I still haven't found a solution.

 

My motherboard is an AMD Gigabyte board (GA-790FXTA-UD5) and is revision 1.0.

 

Processor: AMD Phenom II x2 545 -> working

6 GB DDR3 @ 1333 MHz: Corsair and G.Skill -> only 4GB working with legacy_kernel for 32 bit apps

South Bridge: SB750 (6 SATA II ports, 1 PATA channel) -> working

North bridge: 790FX (PCI-E 2.0 x16) -> using ATI HD 6870 with non-functional HDMI audio

Audio chipset: ALC889 (with Dolby HD) -> not working

Ethernet : 2x Realtek 8111D -> working

eSATA: JMicron 3683 -> working

USB 3.0: Reneses -> working

SATA 3.0: Marvell SE9128 (2 SATA III ports) -> working

1394a (firewire): built-in -> working

 

Audio has : 6 ports and supports 7.1 audio (with mic-in, line-in, and 4 stereo outputs)

 

Everything works except for CMOS reset, other necessary fixes, sleep, shutdown, restart, and most of all... audio (nor ALC889 nor HDMI).

 

If you could help me out that would be great! Thanks B)

 

I've uploaded a clean DSDT from the latest beta bios I'm using (F3J) and using your tool!

 

-xian1243

dsdt.xian1243.zip

 

 

Hello!

I have a ZOTAC ND22, Link to ZOTAC Hompage

this is a nice little barebone with a celereon SU2300 1,2ghz, 4GB RAM. I replaced the WiFi card with a Broadcom (works out of the box).

 

I tried a lot but sleep, shutdown, restart don't work. Now I did a clean new SL install with [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url], so far no [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url] I still boot with [url=&quot;http://www.insanelymac.com/forum/topic/279450-why-insanelymac-does-not-support-tonymacx86/&quot;]#####[/url].

 

There is already a thread about the barebone, unfortunately the dsdt doesn't work

http://www.insanelymac.com/forum/index.php?showtopic=237091

 

 

send_me.zip

 

I would much appreciate, if you could support the ZOTAC ND22 and create a dsdt

 

Best regards

Tom

dsdt.pred8er.zip

Link to comment
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing
×
×
  • Create New...