Micky1979 Posted October 2, 2015 Share Posted October 2, 2015 For NVRAM We need to wait for meklort Link to comment Share on other sites More sharing options...
crazybirdy Posted October 3, 2015 Share Posted October 3, 2015 The ram recognized is wrong here, too. bdmesg is the same as #3536. FYI. Clover r3277 works fine with 10.11.0 as 4G. right as 4G. Enoch r2773 works fine with 10.9.5, 10.10.5 as 4G, but 10.11.0 shows as 4.38G. wrong as 4.38G right as 4G. right as 4G. 1 Link to comment Share on other sites More sharing options...
ncmontas Posted October 3, 2015 Share Posted October 3, 2015 cannot seem to boot my install usb of el capitan that was released on app store, using the latest from enoch branch , Enoch r2773, is it just me or there are others having the issue on booting the chameleon on the installation usb? after waiting for some time white screen appears and a spinning ball. Never had problems on usb installation on my current setup on yosimite, el capitan beta release. Link to comment Share on other sites More sharing options...
Pike R. Alpha Posted October 3, 2015 Share Posted October 3, 2015 Guys here El Capitan final release wont install if the old Recovery HD is present... is the same for you?Can you tell me where it stopped or what happened? What was the last thing you've seen? Link to comment Share on other sites More sharing options...
Micky1979 Posted October 4, 2015 Share Posted October 4, 2015 Pike sorry I will not be at home until tomorrow. The problem was the installer never restart while saying "about a second remain" (waiting more the one hour): So restarting the installer to erase the partition of El Capitan that initially wanted to upgrade, but still endless installation. I later discovered that disk utility from the installer has deleted the OS partition, but not the RecoveryHD associated. Then restarting on another OS (Yosemite) I erased again the ex partition where initially was El Capitan GM using Disk Utility from there... this time the RecoveryHD was deleted successfully. Then installer could end up successful with the installation. That already happened to me with beta 2 on beta1 also.. Link to comment Share on other sites More sharing options...
fusion71au Posted October 4, 2015 Share Posted October 4, 2015 Guys here El Capitan final release wont install if the old Recovery HD is present... is the same for you? @Micky1979, No, everything OK here. I have the following partition arrangement with 2 Recovery HDs (1 Yosemite, 1 El Capitan).... Upgraded from El Capitan GM to final version by directly running the "Install OS X El Capitan.app" from the Applications folder in Yosemite and rebooting into the installer with Enoch 2773. @ncmontas, The failure to boot maybe because FakeSMC is not being injected into the installer's prelinked kernel. Did you install a kernel.plist file in /Extra (and FakeSMC in E/E) on your USB? Alternatively, you can manually enter at the Chameleon menu -v KernelBooter_kexts=Yes Since you have an nVidia card, you can also try adding the flag nv_disable=1 and see if that helps boot the installer... 2 Link to comment Share on other sites More sharing options...
Micky1979 Posted October 4, 2015 Share Posted October 4, 2015 @fusionau71 thanks for reporting. Unfurtunately I had the same problem described here.. and can't understand why.. only assume that is not Enoch related.. @Pike check my PM Link to comment Share on other sites More sharing options...
Pike R. Alpha Posted October 4, 2015 Share Posted October 4, 2015 Pike sorry I will not be at home until tomorrow. The problem was the installer never restart while saying "about a second remain" (waiting more the one hour): So restarting the installer to erase the partition of El Capitan that initially wanted to upgrade, but still endless installation. I later discovered that disk utility from the installer has deleted the OS partition, but not the RecoveryHD associated. Then restarting on another OS (Yosemite) I erased again the ex partition where initially was El Capitan GM using Disk Utility from there... this time the RecoveryHD was deleted successfully. Then installer could end up successful with the installation. That already happened to me with beta 2 on beta1 also.. Hey no problem. This is a different issue. 1.) Downloaded the El Capitan.app 2.) Start installation process. 3.) Reboot 4.) Installation process comes up with "Install OS X" and a blue progress bar. Clicking on the top of the screen bring up the menubar and you can select terminal/safari from it. Nothing seems to work. Anyone seen this before? Link to comment Share on other sites More sharing options...
Micky1979 Posted October 4, 2015 Share Posted October 4, 2015 Yes, is the automated process to upgrade w/o ask you nothing. Is a slow process (very slow) may be it's working and you have to wait a long? Timing changes is you are updrading (to slow because check for old apps compatibility too). With a fresh installation (targeting an empty partition) is more fast. Anyway nothing comparable with the speed of an "restored basesystem.dmg". Or you are experience my issue EDIT probably I have a pict of that process somewhere...let me find it.. EDIT IInope, no pict. EDIT III Apple learning from Windows Link to comment Share on other sites More sharing options...
Pike R. Alpha Posted October 4, 2015 Share Posted October 4, 2015 Ok. I thought that my Skylake setup was borked. Maybe it is. Maybe not, but the PC is sleeping now. {censored}! p.s. There's no progress indication (percentage) so something may be wrong. Link to comment Share on other sites More sharing options...
Micky1979 Posted October 4, 2015 Share Posted October 4, 2015 p.s. There's no progress indication (percentage) so something may be wrong. I can confirm this too, only the blue progress bar (I'm writing from an installation like that) The first time I tried, in the log I had seen that was searching for an active Internet connection (serching for updates), so I do that the 2° time.. not sure has done something particular Link to comment Share on other sites More sharing options...
Pike R. Alpha Posted October 4, 2015 Share Posted October 4, 2015 I had an active Internet connection, now I disabled it. Another thing. I opened Disk Utility/System Information and both are very very slow. Perhaps Apple does something with power management these days and if this thing runs @ 500 MHz... then I can understand why it is slooow. 1 Link to comment Share on other sites More sharing options...
Micky1979 Posted October 4, 2015 Share Posted October 4, 2015 Downgrade Here is fast. Only Xcode is too slow Link to comment Share on other sites More sharing options...
Pike R. Alpha Posted October 4, 2015 Share Posted October 4, 2015 So are we the only people with this problem? Any reports that the installer route works in Chameleon? Link to comment Share on other sites More sharing options...
Micky1979 Posted October 4, 2015 Share Posted October 4, 2015 In my lappy was fine, only my Asus System do that. Link to comment Share on other sites More sharing options...
Pike R. Alpha Posted October 4, 2015 Share Posted October 4, 2015 In my lappy was fine, only my Asus System do that.Interesting. I wonder what the differences are. Both systems have working NVRAM or just your notebook? Link to comment Share on other sites More sharing options...
Micky1979 Posted October 4, 2015 Share Posted October 4, 2015 The notebook had (and I hope will again) a full nvram support installed, desktop not Link to comment Share on other sites More sharing options...
Pike R. Alpha Posted October 5, 2015 Share Posted October 5, 2015 The notebook had (and I hop will again) a full nvram support installed, desktop not That may have been it. And looking at the NVRAM I see a couple of variables. Starting with rc_imgsrc_info (a binary plist) which converted shows me the UUID of the target disk. If you do a Google search you'll only find one hit in the entire Internet. Pretty much hidden for the public. And there are two more starting with .IA but I forgot the exact names... Edit: Here they are 4d1ede05-38c7-4a6a-9cc6-4bcca8b38c14:IASCurrentInstallPhase 4d1ede05-38c7-4a6a-9cc6-4bcca8b38c14:IASInstallPhaseList 8D63D4FE-BD3C-4AAD-881D-86FD974BC1DF:boot-info-payload Link to comment Share on other sites More sharing options...
Micky1979 Posted October 5, 2015 Share Posted October 5, 2015 Edit: Here they are 4d1ede05-38c7-4a6a-9cc6-4bcca8b38c14:IASCurrentInstallPhase 4d1ede05-38c7-4a6a-9cc6-4bcca8b38c14:IASInstallPhaseList 8D63D4FE-BD3C-4AAD-881D-86FD974BC1DF:boot-info-payload I was sure I saw the first variable somewhere, so I turned on my dameged laptop, and in fact is there (even if empty): EDIT scrolling on NVRAMme.app I can see the second variable too: third variables is not there.. Link to comment Share on other sites More sharing options...
Pike R. Alpha Posted October 5, 2015 Share Posted October 5, 2015 Now we need to figure out the contents of it. Probably set some time during the installation process. 1 Link to comment Share on other sites More sharing options...
Micky1979 Posted October 5, 2015 Share Posted October 5, 2015 Yep, that's why my lappy always works with all kind of installers pheraps, Is the "Install El Capitan.app" that set that nvram vars before rebooting?Now I understand completely the meklort's code. We need the uuid of the target disk too, I guess. Link to comment Share on other sites More sharing options...
ncmontas Posted October 5, 2015 Share Posted October 5, 2015 @Micky1979, No, everything OK here. I have the following partition arrangement with 2 Recovery HDs (1 Yosemite, 1 El Capitan).... Disk Partitions and Recovery HDs.png Upgraded from El Capitan GM to final version by directly running the "Install OS X El Capitan.app" from the Applications folder in Yosemite and rebooting into the installer with Enoch 2773. @ncmontas, The failure to boot maybe because FakeSMC is not being injected into the installer's prelinked kernel. Did you install a kernel.plist file in /Extra (and FakeSMC in E/E) on your USB? Alternatively, you can manually enter at the Chameleon menu -v KernelBooter_kexts=Yes Since you have an nVidia card, you can also try adding the flag nv_disable=1 and see if that helps boot the installer... Hi, I had the kernel.plist on my first attempt in the Extra folder. Had to recreate again the installer USB, after that everything went fine, but noticed this error. This happen after the progress bar finishes on the preparation part of the installation of OSX. Oct 5 10:19:52 Mac-Pro Unknown[475]: 2015-10-05 10:19:52.153 Language Chooser[474:7000] TSplicedFont failed creating descriptor for: Oct 5 10:19:52 Mac-Pro Unknown[475]: ( Oct 5 10:19:52 Mac-Pro Unknown[475]: { Oct 5 10:19:52 Mac-Pro Unknown[475]: UnicodeRange = "<__NSCFCharacterSet: 0x7fae350d13f0>"; Oct 5 10:19:52 Mac-Pro Unknown[475]: name = NotoSansBuhid; Oct 5 10:19:52 Mac-Pro Unknown[475]: }, Oct 5 10:19:52 Mac-Pro Unknown[475]: { Oct 5 10:19:52 Mac-Pro Unknown[475]: UnicodeRange = "<__NSCFCharacterSet: 0x7fae350d14a0>"; but after waiting for a while, the installer preparation steps exited forcibly and reboot the computer, and the installation began. Installation of El Capitan was successful. 1 Link to comment Share on other sites More sharing options...
Micky1979 Posted October 5, 2015 Share Posted October 5, 2015 Good! Thanks for testing and report back! Link to comment Share on other sites More sharing options...
ikunikun Posted October 5, 2015 Share Posted October 5, 2015 hello, Now I'm using i3-2125, so I have to rebuild "boot" to enable HD3000. Is it impossible to patch gma.c ? This patch will fix i5-2500K issue, too. --- gma.c (latest) +++ gma.c (working copy) @@ -667,7 +667,13 @@ devprop_add_value(device, "built-in", &BuiltIn, 1); devprop_add_value(device, "class-code", ClassFix, 4); + if(((device_id << 16) | vendor_id) != GMA_SANDYBRIDGE_GT2) { devprop_add_value(device, "vendor-id", (uint8_t *)INTEL_VENDORID, 4); + }else{ + device_id = 0x00000126; + devprop_add_value(device, "device-id", (uint8_t *)&device_id, sizeof(device_id)); + verbose("\tInjeting done: was [%04x:%04x] now is [%04x:%04x]\n", gma_dev->vendor_id, gma_dev->device_id, gma_dev->vendor_id, device_id); + } devprop_add_value(device, "AAPL,tbl-info", HD3000_tbl_info, 18); 2 Link to comment Share on other sites More sharing options...
ErmaC Posted October 5, 2015 Author Share Posted October 5, 2015 hello, Now I'm using i3-2125, so I have to rebuild "boot" to enable HD3000. Is it impossible to patch gma.c ? This patch will fix i5-2500K issue, too. Sure... test it... 2774... boot_2774_TEST.zip Enoch 2 Link to comment Share on other sites More sharing options...
Recommended Posts