WilBUR Posted September 30, 2006 Share Posted September 30, 2006 It does not allow me to type anything in though Link to comment Share on other sites More sharing options...
Rammjet Posted September 30, 2006 Share Posted September 30, 2006 The cursor doesn't move, there are no asterisks or any character displayed, but it is accepting your input. Link to comment Share on other sites More sharing options...
WilBUR Posted September 30, 2006 Share Posted September 30, 2006 I do not think it is because when I type my password and hit enter it says invaild directory when all i typed after opening the terminal was: sudo -s password <ENTER> MYPASSWORD <ENTER> invaild directory.... Link to comment Share on other sites More sharing options...
Rammjet Posted September 30, 2006 Share Posted September 30, 2006 You type: sudo -s <Enter> Then it asks for your password. Then you type: (whatever your password is) <Enter> Link to comment Share on other sites More sharing options...
WilBUR Posted September 30, 2006 Share Posted September 30, 2006 Got past the password part and put in the required fields but I am still not getting an internet connection, possibly did something wrong? Not really big on Unix? (if thats that terminal is) Link to comment Share on other sites More sharing options...
noxdg Posted October 3, 2006 Share Posted October 3, 2006 As much as I hate to ask for help...(usually the answer is staring at me in the face)...I can't get this driver to work with my DGE-530T. I've followed both sets of instructions in this entire thread: 1.) I edited the info.plist with the DGE-530T deviceID (0x4C001186) 2.) Opened the terminal and typed... 3.) sudo -s (password) 4.) cp -R (location of skge.kext to be copied) /System/Library/Extensions/ 5.) rm -R /System/Library/Extensions.kextcache 6.) rm -R /System/Library/Extensions.mkext I rebooted and nothing. I checked the Network area. It's blank. The second set of instructions: 1.) Copy skge.kext in to the /System/Library/Extensions/ 2.) Open Terminal 3.) Entered these command lines: 4.) sudo chown -R root:wheel /System/Library/Extensions/skge.kext 5.) sudo chmod -R 755 /System/Library/Extensions/skge.kext 6.) sudo rm /System/Library/Extensions.mkext 7.) sudo rm /System/Library/Extensions.kextcache Still nothing. Am I missing something? EDIT: Like I mentioned above ...I figured it out. I was doing everything perfectly correct, BUT my device ID was different than the one in this thread. To anyone trying to use a DGE-530T, check the card itself. There should be a revision number written on the top of the card as "REV-B1" (which is mine). That letter and number should replace the ones in this thread's device ID. Example: 0x4C001186 changed to 0x4B011186. It's nice to have the network up and running. All thanks to m.musashi! Link to comment Share on other sites More sharing options...
WINTERS Posted October 18, 2006 Share Posted October 18, 2006 This worked IMMEDIATELY! WOW! THANK YOU FOR MAKING THIS :pirate2: Just for the record: DFI LANParty UT NF4 Ultra-D (dunno which Marvell Yukon ver, but probably 88E8001 too) THANKS!!! =D LTX Need your HELP in my DFI nF4-Ultra D don`t work,, i have installed MAC OS x 10.4.7 JAS Iso REpack, and the installer: Marvell.Gigabit.pkg freeze and can`t install it.. Sorry for my English im from Spain... Link to comment Share on other sites More sharing options...
seleven Posted October 18, 2006 Share Posted October 18, 2006 Just tried 0.2d last night on my machine, works great, thanks m.musashi! Link to comment Share on other sites More sharing options...
seleven Posted October 20, 2006 Share Posted October 20, 2006 And just finished adding it to the 3rd party drivers section in the wiki. http://wiki.osx86project.org/wiki/index.php/3rdPartyDrivers Link to comment Share on other sites More sharing options...
RobNyc Posted October 23, 2006 Share Posted October 23, 2006 http://www.installers.dl.am/ Just curious these wont work for us right? The RealTek sshown there Link to comment Share on other sites More sharing options...
WINTERS Posted October 23, 2006 Share Posted October 23, 2006 Great news, i do a native install DVD with GoatsecX v_10.4.6 and the MARVELL 88E8001 works FULLY.. tHANKS TO ALL PEOPLE that help me... Best wishes from Spain..... Link to comment Share on other sites More sharing options...
LKU1 Posted October 31, 2006 Share Posted October 31, 2006 hi guys, i recently updated my 10.4.5 with internet (skge 0.2d) to 10.4.8 using JaS's 10.4.8 amd sse3 updater my rig has an amd x2 4400+ (s939) i tried to reinstall the skge 0.2d, but to no avail when i check the network area, everything shows up like it did before, but internet in firefox or safari wont work. Link to comment Share on other sites More sharing options...
Lollo85 Posted November 7, 2006 Share Posted November 7, 2006 For Sony Vaio (88E8036) vendor id is: 0x435111AB not 0x43511AB Lorenzo Link to comment Share on other sites More sharing options...
kenny_boy019 Posted November 7, 2006 Share Posted November 7, 2006 I cant even get the thing to install... error file attached... New_Microsoft_Word_Document_2.doc Link to comment Share on other sites More sharing options...
Eidola Posted November 8, 2006 Share Posted November 8, 2006 I can get this working, however I also get A TON of "family specific matching fails" messages on virtually everything there is to get it on... P0P4, ethernet, IDE0, USB1, USB2, USB3, USB4, EUSB, SBRG, P0P1, aci8086... then the nVidial HAL loads and I get a bunch more family specific matching failures. However, the system does boot normally and everything seems to work... so, is this normal and if so, is there any way to disable it? -Eidola Link to comment Share on other sites More sharing options...
Simonb76 Posted November 8, 2006 Share Posted November 8, 2006 Thankyou very much! It worked for me first time after reboot. Asus P5P800 motherboard - Pentium 4 - 3Ghz 630. Link to comment Share on other sites More sharing options...
RobNyc Posted November 9, 2006 Share Posted November 9, 2006 I dont think it works on 10.4.8 OSX Semthex Kernel Its not working for me Link to comment Share on other sites More sharing options...
wondergod Posted November 10, 2006 Share Posted November 10, 2006 Not working on the 10.4.8 mifki kernel for me either, tried replacing with an old IONetworking and still errors. Link to comment Share on other sites More sharing options...
Eidola Posted November 10, 2006 Share Posted November 10, 2006 It does work for me on the 10.4.8 Semthex kernel, though I did download the source and recompile, so that may be the trick to get it working. Link to comment Share on other sites More sharing options...
LKU1 Posted November 10, 2006 Share Posted November 10, 2006 eidola, how do you compile the source? as soon as jas releases a patch for AMD SSE3, i will reinstall 10.4.8 and test this driver if recompiling doesn't work for me Link to comment Share on other sites More sharing options...
Eidola Posted November 11, 2006 Share Posted November 11, 2006 Download and install XCode from Apple's website: http://developer.apple.com/tools/xcode/ Download the source code from the first post on this thread, extract it and then open "skge.xcodeproj" to load the project. When you run XCode for the first time just accept all the default values when it asks about configuration inforation. Once the project is loaded change the dropdown at the top to "Release" from "Debug" then click the Build button. I get two warnings about a struct being defined but never used, since they are warnings and not errors it does not seem to affect the extension in any way. Once compiled you will find your new kernel extension at ./build/Release/skge.kext, copy that into the /System/Library/Extensions folder, set permissions, delete the cache files and reboot. This worked for me, though the compiled version also worked for me on 10.4.8 with Semthex kernel... you may need to set your Vendor and Device ID's to make it work with your particular card. I know I did for my 3Com on an Asus P4P800. Link to comment Share on other sites More sharing options...
matchicken Posted November 11, 2006 Share Posted November 11, 2006 i try to unzip it and then use the terminal and there is a msg like that cp:illegal option -- / usage: cp [-R [-H | -L | -P]] [-f | -i | -n] [-pv] src target cp [-R [-H | -L | -P]] [-f | -i | -n] [-pv] src1 ...srcN directory what should i do i have no idea at all thz Link to comment Share on other sites More sharing options...
ooZberg Posted November 15, 2006 Share Posted November 15, 2006 I have a DFI Lanparty NF4 with Marvell Yukon 8001 and now running semthex last kernel, works like charm with this driver All I did was just installed a older version of IONetworkFamily.kext, like in this thread (http://forum.insanelymac.com/index.php?showtopic=33261&hl=marvell) I don't know if this was relly needed, but I heard you guys complining about this driver not working under semthex kernel, so maby this could be a solution Link to comment Share on other sites More sharing options...
dancemc87 Posted November 16, 2006 Share Posted November 16, 2006 i have the 88E8055 - could this work with this driver as well?? how do i install drivers under mac os x - i am a newbie to "hackintosh" ;-) by the way: which one is the better kernel - semthex or mifki kernel?? pls tell me (private message also possible if this does not fit into this thread ^^) thanks a lot Link to comment Share on other sites More sharing options...
RobNyc Posted November 18, 2006 Share Posted November 18, 2006 I'll just wait and see what happens =\ Link to comment Share on other sites More sharing options...
Recommended Posts