brif8 Posted December 30, 2010 Share Posted December 30, 2010 Can someone please give help I have a Zotac 9800 GT 1GB can not get Dual monitors to work at all. The Zotac will only work with the VGA If I have the DVI connected it will not boot So I bought an ATI 4350 1GB Now when I swap over I get a white screen after 40 sec of the Apple with the rotating wheel So I though it might be because of the NVidia Drivers so I swapped back and removed the NVD*.kext from the S/L/E directory and NVEnabler 64.kext from the E/E directory Still no joy in getting the new card to work Now I have my Nvidia back in and I can only get 1024x768 resolution which looks {censored} Please How do I get my ATI 4350 1GB to work and hopefully with Dual Monitors Thanks in advance Link to comment Share on other sites More sharing options...
brif8 Posted December 31, 2010 Share Posted December 31, 2010 Not sure If I'm going forward or backward I have removed all NVidia and deleted the com.apple.kext.caches from /S/L/C Now when I boot using the ATI 4350 card It boots and then both monitors power down (Orange light) and black display IMPLIES NO INPUT signal I can ssh into the machine so it booted and is running but nothing shows on either display (DVI or VGA) Darwin/x86 boot v5.0.132 - Chameleon v2.0-RC4_PCEFI_10.5_AsereBLN r BuildDate: 2010-02-12 01:05:22 3071MB memory When booting with -x -v I see mbinit: done (64 MB memory set for mbuf pool) netkas presents fakesmc, a kext which emulates smc device HDAEnabler: copyright © 2008 by Kabyl HDAEnabler: 05/05/2008 Added SPAudio support: Taruga Not loading kext com.apple.kext.ATI4600Controller - not found and kextd not available in early boot HDAEnabler: copyright © 2008 by Kabyl HDAEnabler: 05/05/2008 Added SPAudio support: Taruga FireWire runtime power conservation disabled (2) From path: "uuid", Waiting for boot volume with UUID B3B..... .... .... Previous Shutdown Cause: 0 ACPI_SMC_PlatformPlugin::start - waitForService(resourceMatching(AppleIntelCPUPowerManagement) timed out DSMOS has arrived That is the last thing seen before the screens blank out scroll by again screens go blank (NO INPUT signal) ATI4600Controller.kext does exist in /S/L/E ATI4600Controller 1.6.24.17 (8901) When booting with -x -f I see the Apple Logo Spinning wheel and a progress bar (gray rounded edges) Slowly moves to about 30% then progress bar disappears and the wheel keeps spinning for 20 secs and then again Blank displays (or No Input Displays) Seeing I have ssh access is there any command line stuff I can do like Kext Utility loads, or EFI Studio ??? Any ideas ?? Gaining Remote Screen Sharing Access I have found the following In System Profiler Chipset Model: ATI Radeon 4300 Type: GPU Bus: PCIe Slot: Slot-1 PCIe Lane Width: x16 VRAM (Total): 1024 MB Vendor: ATI (0x1002) Device ID: 0x954f Revision ID: 0x0000 ROM Revision: 113-B7710C-176 EFI Driver Version: 01.00.318 Displays: Display Connector: Display Connector: So it has detected the Graphics Cards Not the Displays?? Thanks in advance Link to comment Share on other sites More sharing options...
ayaw Posted January 1, 2011 Share Posted January 1, 2011 Not sure If I'm going forward or backwardI have removed all NVidia and deleted the com.apple.kext.caches from /S/L/C Now when I boot using the ATI 4350 card It boots and then both monitors power down (Orange light) and black display IMPLIES NO INPUT signal I can ssh into the machine so it booted and is running but nothing shows on either display (DVI or VGA) Darwin/x86 boot v5.0.132 - Chameleon v2.0-RC4_PCEFI_10.5_AsereBLN r BuildDate: 2010-02-12 01:05:22 3071MB memory When booting with -x -v I see mbinit: done (64 MB memory set for mbuf pool) netkas presents fakesmc, a kext which emulates smc device HDAEnabler: copyright © 2008 by Kabyl HDAEnabler: 05/05/2008 Added SPAudio support: Taruga Not loading kext com.apple.kext.ATI4600Controller - not found and kextd not available in early boot HDAEnabler: copyright © 2008 by Kabyl HDAEnabler: 05/05/2008 Added SPAudio support: Taruga FireWire runtime power conservation disabled (2) From path: "uuid", Waiting for boot volume with UUID B3B..... .... .... Previous Shutdown Cause: 0 ACPI_SMC_PlatformPlugin::start - waitForService(resourceMatching(AppleIntelCPUPowerManagement) timed out DSMOS has arrived That is the last thing seen before the screens blank out scroll by again screens go blank (NO INPUT signal) ATI4600Controller.kext does exist in /S/L/E ATI4600Controller 1.6.24.17 (8901) When booting with -x -f I see the Apple Logo Spinning wheel and a progress bar (gray rounded edges) Slowly moves to about 30% then progress bar disappears and the wheel keeps spinning for 20 secs and then again Blank displays (or No Input Displays) Seeing I have ssh access is there any command line stuff I can do like Kext Utility loads, or EFI Studio ??? Any ideas ?? Gaining Remote Screen Sharing Access I have found the following In System Profiler Chipset Model: ATI Radeon 4300 Type: GPU Bus: PCIe Slot: Slot-1 PCIe Lane Width: x16 VRAM (Total): 1024 MB Vendor: ATI (0x1002) Device ID: 0x954f Revision ID: 0x0000 ROM Revision: 113-B7710C-176 EFI Driver Version: 01.00.318 Displays: Display Connector: Display Connector: So it has detected the Graphics Cards Not the Displays?? Thanks in advance I experience this too when I reinstall my hackintosh first i'm in 10.6, I need to boot with "-x -f arch=i386" to get rid of blank screen then I do 10.6.5 update, reinject the device id to Info.plist and it works fine now without any bootflags Link to comment Share on other sites More sharing options...
brif8 Posted January 1, 2011 Share Posted January 1, 2011 then I do 10.6.5 update, reinject the device id to Info.plist and it works fine now without any bootflags Currently I have DVI working only when connected to a DVI monitor using a DVI to VGA converter does NOT work Still the VGA to VGA monitor does NOT work How do you reinject the device id to Info.plist ??? Can you please break this into steps for me Thanks Link to comment Share on other sites More sharing options...
ayaw Posted January 1, 2011 Share Posted January 1, 2011 Currently I have DVI working only when connected to a DVI monitor using a DVI to VGA converter does NOT workStill the VGA to VGA monitor does NOT work How do you reinject the device id to Info.plist ??? Can you please break this into steps for me Thanks Just tried to replace my DVI cable to VGA cable to test this out. Seems like this works on DVI only. VGA isn't working, still get the blank screen. To inject the device id, look at this post : http://www.insanelymac.com/forum/index.php?showtopic=221422# There is a detailed information about adding the device id in the middle of the post. Link to comment Share on other sites More sharing options...
nei-k Posted January 3, 2011 Share Posted January 3, 2011 I have same problem too. I tried everything but I can not get rid of black screen. Snow Leopard boots but without signal from videocard Link to comment Share on other sites More sharing options...
brif8 Posted January 3, 2011 Share Posted January 3, 2011 I have same problem too. I tried everything but I can not get rid of black screen. Snow Leopard boots but without signal from videocard I know it can be hard I managed to get the DVI working by simply using a DVI monitor Still can not get VGA to work thou, my ATI4500Controller.kext and ATIRadeonX2000.kext already had the Device ID Still would like to get the VGA to function Link to comment Share on other sites More sharing options...
nei-k Posted January 3, 2011 Share Posted January 3, 2011 I have only an VGA connector in my iiyama display. My card is an HIS ATI 4350 with VGA, DVI and HDMI connectors. I tried both VGA and DVI (with VGA adaptor) without luck. I Did not try the HDMI connector Link to comment Share on other sites More sharing options...
plipli Posted January 6, 2011 Share Posted January 6, 2011 Anyone updated to 10.6.6 ? Lots of ATI kext inside this update :s EDiT : no change inside the kext I have checked, trying now to update EDiT2 : update failed, now in -x, I will check the ATI kexts. EDiT3 : added 0x954f1002 to ATI4600, rebooting... EDiT4: wouhou success ! EDiT5: woot green icons in AppStore ! 1 Link to comment Share on other sites More sharing options...
nei-k Posted January 7, 2011 Share Posted January 7, 2011 Great! I will try to update when I get home. Your monitor has DVI or VGA input? Mine has only VGA input and in 10.6.5 version I get blank screen no matter if i connect to the video card by VGA port or by DVI port via donngle Link to comment Share on other sites More sharing options...
ANARCHiNTOSH Posted January 8, 2011 Share Posted January 8, 2011 thanks for testing plipli btw, there is a device-id injector kext for 4600controller over at post here its called ATI4350.Fix.v2, and it's in ATI4350.Fix.MULTi.zip Link to comment Share on other sites More sharing options...
nei-k Posted January 12, 2011 Share Posted January 12, 2011 I have given up trying to setup my Ati 4350, and I bought a Palit G210 that worked out of the box on my system Link to comment Share on other sites More sharing options...
smokeymcpot Posted April 24, 2011 Share Posted April 24, 2011 I have given up trying to setup my Ati 4350, and I bought a Palit G210 that worked out of the box on my system Got everything working on 10.6.6 but I got a question .. Anyone trying to get this working on Lion? Link to comment Share on other sites More sharing options...
arikstress Posted October 20, 2011 Share Posted October 20, 2011 yaaaaaaaaay i finally can make my HIS ATI HD 4350 working!!!! working flawlessly , but i make it work only at SL 10.6.8 Link to comment Share on other sites More sharing options...
chessperso Posted October 31, 2011 Share Posted October 31, 2011 Everybody who's got a 4xxx, you want to take a look at the 28th of october update of the 20th post of this other topic ! Link to comment Share on other sites More sharing options...
spidy86 Posted May 6, 2012 Share Posted May 6, 2012 Read plipli's post and did same, added devid to ATI4600.kext, ...didnt set GraphicEnabler and ncpi options. Got diplay card detecting 1080p and set overscan ..........my 4350 works goods! except the Only problem that is infamous Green Apple,......plz suggest how can i remove it? if anybody knows how to get rid of this OpenGL issue, plz do share! also how to check qe/ci is working or not? Link to comment Share on other sites More sharing options...
fbifido Posted July 2, 2012 Share Posted July 2, 2012 how to check qe/ci is working or not? Try to start dvd player and chess in Application Link to comment Share on other sites More sharing options...
sciueferrara Posted August 11, 2012 Share Posted August 11, 2012 How to make this card working in Mountain Lion? Please!!! Link to comment Share on other sites More sharing options...
Recommended Posts