gbonilla Posted January 16, 2009 Share Posted January 16, 2009 Hey Urthwhyte do you think you could go and change the path from 19 27 7 to 20 27 7 on MacGirl's and check if the mic works? I know the codecgraph doesn't show it but I'm just interested and it's worth a shot. My bad I forgot to say to change the configdata. I made it, can you just try this? FixNode20.zip Link to comment Share on other sites More sharing options...
talisman Posted January 16, 2009 Author Share Posted January 16, 2009 Hey Urthwhyte do you think you could go and change the path from 19 27 7 to 20 27 7 on MacGirl's and check if the mic works? I know the codecgraph doesn't show it but I'm just interested and it's worth a shot. My bad I forgot to say to change the configdata. I made it, can you just try this? FixNode20.zip Again Ill drop my opinion and not do any actual work.... I don't think 20 will work. The fact that 19 actually responds in certain ways (as seen by macgirl in her working kext, and by me earlier in my non working kext) tells me that it has to be 19. What I think will make the difference is the code in the Info.plist. Can someone check if the king made any changes to the dsp kext info.plist? Something has to tell the driver that the mic is digital and the rest is not.... Link to comment Share on other sites More sharing options...
jacparty Posted January 17, 2009 Share Posted January 17, 2009 hi every one. i have a dell m1330 sigmatel 9228 I'm bit confuse about configdata i get node and pindefault from codecdump how i get config data? I read King post but get strange value rispect configdata in the first post thanks Link to comment Share on other sites More sharing options...
talisman Posted January 17, 2009 Author Share Posted January 17, 2009 hi every one. i have a dell m1330 sigmatel 9228I'm bit confuse about configdata i get node and pindefault from codecdump how i get config data? I read King post but get strange value rispect configdata in the first post thanks Try doing it from a vista pinconfigdata dump. Its a lot easier. You will find the instructions and links in the first post of this thread.... Link to comment Share on other sites More sharing options...
Yehor Lvivski Posted January 21, 2009 Share Posted January 21, 2009 is this whole theme dead? or are there any ways to make mic work at the same time as output %) Link to comment Share on other sites More sharing options...
macgirl Posted January 23, 2009 Share Posted January 23, 2009 Every time you active the node for Mic the Speakers lost sound and Mic stops working. They both cancel each other, maybe the binary needs a patch. Link to comment Share on other sites More sharing options...
Urthwhyte Posted January 23, 2009 Share Posted January 23, 2009 Macgirl: so does that mean that the mic is analog and so there's no point in pursuing stuff with DSP, or just that messing with pathmaps is not going to get us anywhere? Link to comment Share on other sites More sharing options...
talisman Posted January 24, 2009 Author Share Posted January 24, 2009 Macgirl: so does that mean that the mic is analog and so there's no point in pursuing stuff with DSP, or just that messing with pathmaps is not going to get us anywhere? I am more than sure that the mic is digital and at 19. Now I do agree with Miacgirl.... it might need a patch of the binary... I am still swamped... Probably next week.... Link to comment Share on other sites More sharing options...
Urthwhyte Posted January 24, 2009 Share Posted January 24, 2009 If you can tell me what would need to be patched I could take a crack at it this weekend. Link to comment Share on other sites More sharing options...
Jflores Posted January 29, 2009 Share Posted January 29, 2009 hi everyone, I was hoping someone could help me, I installed AppleHDA.kext.M1330.zip by gbonilla and I finally have sound, I was wondering if it is possible to use either internal speakers or headphones, I have normal sound through speakers but if I connect the headphones I hear the sound from both, if I change output to headphones I get no sound at all, is it possible to avoid sound through speakers if I'm using headphones? Thanks in advance! Link to comment Share on other sites More sharing options...
talisman Posted January 30, 2009 Author Share Posted January 30, 2009 hi everyone, I was hoping someone could help me, I installed AppleHDA.kext.M1330.zip by gbonilla and I finally have sound, I was wondering if it is possible to use either internal speakers or headphones, I have normal sound through speakers but if I connect the headphones I hear the sound from both, if I change output to headphones I get no sound at all, is it possible to avoid sound through speakers if I'm using headphones? Thanks in advance! You should have autoswitching on one port.... Did you repair permissions after installing the kext? Macgirl and wingrunr21 are the best people to help you out.. Hunt them down.... Link to comment Share on other sites More sharing options...
Jflores Posted January 30, 2009 Share Posted January 30, 2009 Looks like it actually does work, if I plug the headphones in the first port i get sound though speakers and headphones, if I plug in the second port I get no sound at all but if I return to the first port it switches to headphones only and then the second port starts to work too. Thanks. Link to comment Share on other sites More sharing options...
wingrunr21 Posted January 30, 2009 Share Posted January 30, 2009 If you can tell me what would need to be patched I could take a crack at it this weekend. The mic is indeed digital. If the actual binary needs patched then someone is going to have to hex edit the AppleHDA binary and figure out what needs to be edited. Not an easy task. If we are going to continue to pursue a pathmaps avenue, perhaps browsing the ALSA source would be beneficial. I have attached the appropriate source files for ALSA 1.0.16 which apparently gives full support for the digital mic. Specifically, there is a struct called stac927x_pin_nids which may be of some use: static hda_nid_t stac927x_pin_nids[14] = { 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f, 0x10, 0x11, 0x12, 0x13, 0x14, 0x21, 0x22, 0x23, }; hda.zip Link to comment Share on other sites More sharing options...
Neonkoala Posted January 31, 2009 Share Posted January 31, 2009 I have tried several versions of AppleHDA combined with HDAEnabler in my EFI partition for a retail boot but none seem to load. I have even modified the Info.plist to change the version number to see if it 'prefers' this. Perhaps AppleAzaliaAudio needs to be disabled? Any ideas how to do this from EFI rather than deleting? Thanks. Link to comment Share on other sites More sharing options...
Urthwhyte Posted January 31, 2009 Share Posted January 31, 2009 As with NVInject, AppleHDA.kext won't load from an EFI partition. I don't currently have OS X installed on my internal HD, and my backup is currently being used by a friend for a school project, but what I can do for you is modify the FixAppleHDA.kexts with the correct info for the M1530, and see if those will load up correctly from the EFI partition. Link to comment Share on other sites More sharing options...
Neonkoala Posted January 31, 2009 Share Posted January 31, 2009 I have tried some posted by macgirl in another thread claiming to be modified Legacy AppleHDA kexts for use on the M1530 but they didn't seem to load. I have been looking for EFI strings now as that's what I'm using for my graphics card. Link to comment Share on other sites More sharing options...
macgirl Posted February 1, 2009 Share Posted February 1, 2009 Those kexts need HDAEnabler, don't know if they work with EFI strings. Link to comment Share on other sites More sharing options...
Neonkoala Posted February 1, 2009 Share Posted February 1, 2009 Those kexts need HDAEnabler, don't know if they work with EFI strings. Thanks, it works fine now, I thought as there were two kexts one functionally replaced the HDAEnabler! Doh! Thanks a lot though, yeh xbc told me EFI strings didn't work. Link to comment Share on other sites More sharing options...
Urthwhyte Posted February 9, 2009 Share Posted February 9, 2009 Has anyone made progress on getting the mic working? Link to comment Share on other sites More sharing options...
Neonkoala Posted February 11, 2009 Share Posted February 11, 2009 Has anyone made progress on getting the mic working? Keep an eye on VoodooHDA, seems to be a project to bring mic/line ins to the AppleHDA driver. I believe it's in closed beta currently. Link to comment Share on other sites More sharing options...
Urthwhyte Posted February 11, 2009 Share Posted February 11, 2009 I hadn't heard about that, however now that I've gotten mirroring worked out, my main problem is USB Mass Storage devices disconnecting on resuming from sleep. Link to comment Share on other sites More sharing options...
gbonilla Posted February 19, 2009 Share Posted February 19, 2009 Where are the mics located on the m1530 and the m1330? Are they next to the mic and near the headphone ports? On the Dell Inspiron 1525 the webcam mic is the 0x13 mic and there is another near the headphone ports which is 0x0c Link to comment Share on other sites More sharing options...
macgirl Posted February 20, 2009 Share Posted February 20, 2009 The mic jack, which also is line output or line input is at front whre the other two jacks for headphones are, like this: O O O HP HP Mic Mic port here is 0x0c The internal mic array are two little holes arround the webcam, like this: . º . Mic port here is 0x13 Link to comment Share on other sites More sharing options...
talisman Posted February 21, 2009 Author Share Posted February 21, 2009 Its the same in the M1530..... As far as I know.... Voodoo always works..... Link to comment Share on other sites More sharing options...
immo Posted February 22, 2009 Share Posted February 22, 2009 HDMI Audio Great work on the sound Kext Talisman! OS-X on my M1330 is at the point now where it works well enough that I'm using it more than Windows now. There is still one thing missing though that I have to use Windows for, and that's audio through the HDMI port. Have you or anyone tried this and got this to work? It's extremely useful for hooking up to my HDTV and to my HDMI monitor with speakers. I'm using iAtkos v5i upgraded to 1.5.6 via auto updates, and I am using your stable M1330 drivers. Link to comment Share on other sites More sharing options...
Recommended Posts