[HOW TO] Patch AppleHDA - Knowledge Base

[coconup]

@ the king, how does this mutegpio calculation work? btw I think u should put that table in the first post..

 

also, do u have any idea of why my digital out works only with ac power plugged in and with some precise values in smbiosenabler? when I unplug my laptop the red light coming out from the spdif jack turns off, and my internal speakers work worse...

 

edit: back from some tests

 

almost all those values killed my audio. except from the mic and line in ones, which I already had, changing internal speakers from 0 and headphones from their current value resulted in a lot of sound assertions and no audio after boot.

 

the only one that worked is the spdif out (pin 30), but it didn't really make any difference...

[Hugo_bee]

hy the king.. I see you're here now.

What do you suggest to do?

I always thinked that there are very few differences between a retail and a hack dvd setup. .

yes I no it's not the same.. but now I feel panic if I think at a hundred of topics to explain 100 different mothod to install a retail.

ok.. it must be done! then.. i'll do.

I give you the answer from others it users.. only to maintain this useful conversation.

 

bye

[coconup]

I noticed that you did not include pin config for my external mic:-

01871c30 01871d98 01871ea1 01871f01

 

oops, sorry for missing that , try it this way 01871c30 01871d90 01871ea1 01871f01

 

This is what actually happen to me but it happen to my internal speaker & headphone.

 

 

You mean that you just switch the mutegpio value between them?

 

kizwan

 

yes, simple as that.. btw I'm now really over with this codec, everything works perfectly, so you can start by patching my kext with your pin configuration

 

ALC883.zip

[THe KiNG]

@ the king, how does this mutegpio calculation work? btw I think u should put that table in the first post..

 

also, do u have any idea of why my digital out works only with ac power plugged in and with some precise values in smbiosenabler? when I unplug my laptop the red light coming out from the spdif jack turns off, and my internal speakers work worse...

I think is better for tmongkol to answer himself.

I asked him to join me in this patching effort(and for others if they want) and to rewrite this guide/start a new one with better n00b explanation etc.

Also I will create a new # to discuss this on irc(atm servers are borked) after is fixed, imo better to keep this/new guide clean and discuss live the problems...

 

About smbios, I dont use any smbios enabler, I fixed my stuff in DMI see my lappie guide for how to, also some stuff are injected by chameleon...

So dunno what can be your problem.

 

hy the king.. I see you're here now.

What do you suggest to do?

I allways suggest retail, that way you can be almost sure that is not smth else that borke your work...

IMO use Munky guide, best one so far...or take a choice...

[coconup]

well it looks like the spdif out mutegpio value under [vref80 column - pin 30] made my digital out 'last more', but after some minutes on battery it still turns off. It also seems that this thing affects the whole power detection, since with different values of mutegpio the battery meter doesn't detect things properly...

[nobb1x]

Hi The King!! Acer 5930g/ALC888S here, i tried your kext published few post ago but it don't work at all, but, i have the 888 partly working using the kext you did for your Asus laptop, what i have working is INT Speakers,Headphone out(not autoswitching) and sometimes (don't laugh pls, one time every 10 restarts about) the external mic in.

Int mic and line in are always not working, line in is not displayed in systemprofiler too.

What i've changed is the ConfigData, adding pin configuration taken from the Vista driver and i've removed the HDAEnabler inside of it because it was crashing my machine.

To have the proper layoutID injected i've used an EFI string only.

 

Attached is the modified kext (i suggest those of you with a 5930/6930 to try it), the alc888S datasheet pin layout and my system log of a restart with all the applehda related errors.

Could you try to look at it? many thanks

 

The codec dump is the same as Ugokind's machine (i think) and i can see some differences from the pin layout in the datasheet and the one from the codec dump (maybe i misread it )

 

n.b. this kext is not work of mine, regards to The King

 

About my config, not that in the sig, Acer 5930G 4GB, Vanilla 10.5.6 kernel, iPC 10.5.6, no ALCinject,no HDAEnabler, Vanilla 10.5.6 AppleHDA

ACERALC888S.kext.zip

system.zip

alc888s.tiff

[THe KiNG]

Is there an agreement on what to do with 71d Misc values that are >1 ?

 

I've come across a couple of codec dumps that have alternate values such as 6, 8, and c in that field.

 

I can guess what to do but I'm trying to help automate the verb conversion process with a script.

 

Sample:

--------------------------------------------------------------------------------------------------------
Verbs from Linux Codec Dump
--------------------------------------------------------------------------------------------------------
Codec: Realtek ALC1200
Address: 0
Vendor Id: 0x10ec0888
Subsystem Id: 0x104382fe
Revision Id: 0x100101

  Jack   Color  Description				  Node	 PinDefault				 Verbs
--------------------------------------------------------------------------------------------------------
 ATAPI Unknown  SPDIF Out at Int ATAPI	  17 0x11   0x99430140   01171c40 01171d01 01171e43 01171f99
1/8   Green  Line Out at Ext Rear		20 0x14   0x01014010   01471c10 01471d40 01471e01 01471f01
1/8   Black  Line Out at Ext Rear		21 0x15   0x01011012   01571c10 01571d10 01571e01 01571f01
1/8  Orange  Line Out at Ext Rear		22 0x16   0x01016011   01671c10 01671d60 01671e01 01671f01
1/8	Grey  Line Out at Ext Rear		23 0x17   0x01012014   01771c10 01771d20 01771e01 01771f01
1/8	Pink  Mic at Ext Rear			 24 0x18   0x01a19850   01871c50 01871d98 01871ea1 01871f01
1/8	Pink  Mic at Ext Front			25 0x19   0x02a19c60   01971c60 01971d9c 01971ea1 01971f02
1/8	Blue  Line In at Ext Rear		 26 0x1a   0x0181305f   01a71c50 01a71d30 01a71e81 01a71f01
1/8   Green  HP Out at Ext Front		 27 0x1b   0x02214c20   01b71c20 01b71d4c 01b71e21 01b71f02
 ATAPI Unknown  CD at Int ATAPI			 28 0x1c   0x593301f0   01c71cf0 01c71d01 01c71e33 01c71f59
Optical   White  Speaker at Ext N/A		  29 0x1d   0x4015e601   01d71c00 01d71de6 01d71e15 01d71f40
Optical  Orange  SPDIF Out at Ext Rear	   30 0x1e   0x01456130   01e71c30 01e71d61 01e71e45 01e71f01
1/8   Black  Speaker at Ext Rear		 31 0x1f   0x411111f0   01f71cf0 01f71d11 01f71e11 01f71f41
--------------------------------------------------------------------------------------------------------

 

I'm forcing Sequence to 0 and have the idea on what to do for port/location.

Just wanted to find out about these "high" values for Misc as they do cause assertion errors.

What are you trying to do is nice, but I'm not 100% sure it will work...

Catch me on irc, when is fixed(irc server) I will explain you more stuff to implement.

 

Hi The King!! Acer 5930g/ALC888S here, i tried your kext published few post ago but it don't work at all, but, i have the 888 partly working using the kext you did for your Asus laptop, what i have working is INT Speakers,Headphone out(not autoswitching) and sometimes (don't laugh pls, one time every 10 restarts about) the external mic in.

Int mic and line in are always not working, line in is not displayed in systemprofiler too.

What i've changed is the ConfigData, adding pin configuration taken from the Vista driver and i've removed the HDAEnabler inside of it because it was crashing my machine.

To have the proper layoutID injected i've used an EFI string only.

 

Attached is the modified kext (i suggest those of you with a 5930/6930 to try it), the alc888S datasheet pin layout and my system log of a restart with all the applehda related errors.

Could you try to look at it? many thanks

 

The codec dump is the same as Ugokind's machine (i think) and i can see some differences from the pin layout in the datasheet and the one from the codec dump (maybe i misread it )

 

n.b. this kext is not work of mine, regards to The King

 

About my config, not that in the sig, Acer 5930G 4GB, Vanilla 10.5.6 kernel, iPC 10.5.6, no ALCinject,no HDAEnabler, Vanilla 10.5.6 AppleHDA

What you did is the same Marry with other hat...

HDAEnabler cant panic the SO unless you have a borked one or use on the same time more fixes for the same thing e.g efi strings alcinject and hdaenabler at the same time or in combinations...

No wonder your mic is not working since in plist is NID 25(mine) and yours is NID18, and what you added on configdata is wrong(not fixed) and my guess same sh*t is also in efistrings.

I will stop trying to help you guys until who want to test make a clean retail test install, not some iSh*t or whatever distro you use, and do what I say to do/use for test.

[kidalive]

What I told you to do and what you did....

Dunno wtf is so hard to do just what I said.

Just put my kext with hdaenabler(check first post @ the end) with original AppleHDA.kext in /s/l/e

DON'T TOUCH that damn original AppleHDA.kext!

I really don't understand why you guys take always the hard way instead easy way

 

I`ve got my Internal Mic working. I found your guide miss a important part to make the Internal Mic working. It`s important to modify the applehdacontoller.kext correct or the Int Mic won`t work. Do you agree? But I got a little bit low recording volume. I think it can be done by modfying the applehdaplatform.kext since I modified from the original applehda.kext.

Whatever ur guide helped me in someway, thanks. I`m tring to use the DSDT patch way to get it working now, but I`m no sure will that enable the sleep founction.

[kizwan]

Hi coconup,

 

EDIT: ALC883 on my Acer Aspire 3680 is now working. Need to remove MuteGPIO entry for both speaker & headphone. I have uploaded the revised Info.plist of AppleHDAPlatformDriver.kext.

Thank you for your help. I really appreciated it. All available devices (mic, external mic, line in, HP out & speaker) on my ALC883 (Acer Aspire 3680) are working except a couple of minor problem. Because I can't find correct combination of MuteGPIO for headphone & internal speaker yet. Also I have to choose only two from three input devices (mic, external mic, line in) because I only have two NID for input (8-35 & 9-34).

 

As you can see, I set mutegpio for headphone to 0 & speaker to 1,342,242,843. I will get mute on speaker & audio out on headphone. If I split them to individual pathmap, I will get audio out on speaker for a while before it mute. No problem with headphone though. If I switch the mutegpio between speaker & headphone, the effect will also switched. I think I will have to live with that for now until I figure out how to fix it.

I attached here all the files (codec dump, pin config, ConfigData, svg files & etc) that I collected during the process.

alc883_aceraspire3680_dump_kizwan.zipAppleHDAPlatformDriverkext.zip <-- correct layout

Kext for use with Boot-132:-

ALC883Aspire3680.kext.zip

 

kizwan

[coconup]

kizwan, you can try some combinations of the mutegpios the king posted in the previous page, they didn't work for me and I also found strange that my hp mutegpio is the one that normally goes under the line out pin (27), but maybe they'll work for you

 

eg. try different combinations of these values

 

0 (normally internal speaker)

1,342,242,836 (normally internal speaker)

1,342,242,837 (normally hp)

1,342,242,843 (normally line out)

 

ps: are you using my kexts? cos it's strange that your internal mic is shown as external... I had this issue but I solved it yesterday, by switching those mutegpios as I posted. now I can use A0 90 for the internal mic, which didn't work before and I had to use A0 00

 

 

edit: I understood the mutegpio calculation... eg for pin 20 vref 80 -> 50010014 in hex, so 50 is the vref and 14 the pin (in hex).. but are you sure that 0100 in the middle is constant? what does it refer to?

[kizwan]

Hi coconup,

 

I did it! Since THe KiNG mention that MuteGPIO value depend on VREF value, so I check back my codec dump. I found that no VREF entry for speaker & headphone. So, I just remove MuteGPIO entry for both devices. After that, both speaker & headphone working (auto-switch). I also compare it with AppleHDA.kext (ALC883) patched with Taruga patcher & it match.

 

Thank you very much THe KiNG & coconup.

 

.............................

ps: are you using my kexts? cos it's strange that your internal mic is shown as external... I had this issue but I solved it yesterday, by switching those mutegpios as I posted. now I can use A0 90 for the internal mic, which didn't work before and I had to use A0 00

 

 

edit: I understood the mutegpio calculation... eg for pin 20 vref 80 -> 50010014 in hex, so 50 is the vref and 14 the pin (in hex).. but are you sure that 0100 in the middle is constant? what does it refer to?

No, I'm not using your kext. I just compare & try your MuteGPIO value. Referring to your dump, you don't have Line In but I have (refer to my dump & pin config - post #310). I have to choose only 2 devices for input (mic, external mic & line in) because I only have 2 NID for input (8-35 & 9-34). I chose external mic & line in, that is why you see external mic & line in.

If I choose internal mic, it will working after I corrected the MuteGPIO value (because VREF is 80) & it is the exact match with the value from MuteGPIOs table posted by THe KiNG. I also need to set Connection Type to 0 & Location to 0 (A0 90). I think only internal speaker can be set with Connection Type to 3 (ATAPI).

Aaahhhh....you figure out how to calculate the MuteGPIO value. I need to write this down. You're right, I think, (eg for pin 20 vref 80 -> 50010014 in hex) 50 is VREF in hex but I guess 014 is NID in hex & 010 is constant. What do you think?

 

kizwan

[DPyro]

Hi, can someone please check my nodes. I redid it, and think I know what I'm doing now, but need confirmation. I then need help to get the pin configs right.

 

Thanks!

 

EDIT: I figured out how to do the verbs

 

[b]NID 17 [Jack] Digital Out at Int HDMI[/b]
Node - 0x11
Pin Default - 0x18561130
Verb - 01171C30 01171D11 01171E56 01171F18

[b]NID 18 [Fixed] Mic at Int ATAPI[/b]
Node 0x12
Pin Default - 0x99a3094e
Verb - 01271C4E 01271D09 01271EA3 01271F99

[b]NID 20 [Fixed] Speaker at Int ATAPI[/b]
Node - 0x14
Pin Default - 0x99130110
Verb - 01471C10 01471D01 01471E13 01471F99

[b]NID 21 [Jack] HP Out at Ext Front[/b]
Node - 0x15
Pin Default - 0x0221101f
Verb - 01571C1F 01571D10 01571E21 01571F02

[b]NID 22 [N/A] Speaker at Ext Rear[/b]
Node - 0x16
Pin Default - 0x411111f0
Verb - 01671CF0 01671D11 01671E11 01671F41

[b]NID 23 [N/A] Speaker at Ext Rear[/b]
Node - 0x17
Pin Default - 0x411111f0
Verb - 01771CF0 01771D11 01771E11 01771F41

[b]NID 24 [Jack] Mic at Ext Front[/b]
Node - 0x18
Pin Default - 0x02a19c40
Verb - 01871C40 01871D9C 01871EA1 01871F02

[b]NID 25 [N/A] Speaker at Ext Rea[/b]r
Node - 0x19
Pin Default - 0x411111f0
Verb - 01971CF0 01971D11 01971E11 01971F41

[b]NID 26 [Jack] Line In at Ext Front[/b]
Node - 0x1A
Pin Default - 0x02813441
Verb - 01A71C41 01A71D34 01A71E81 01A71F02

[b]NID 27 [N/A] Speaker at Ext Rear[/b]
Node - 0x1B
Pin Default - 0x411111f0
Verb - 01B71CF0 01B71D11 01B71E11 01B71F41

[b]NID 28 [N/A] Speaker at Ext Rear[/b]
Node - 0x1C
Pin Default - 0x411111f0
Verb - 01C71CF0 01C71D11 01C71E11 01C71F41

[b]NID 29 [N/A] Speaker at Ext Rear[/b]
Node - 0x1D
Pin Default - 0x4016852d
Verb - 01D71C2D 01D71D85 01D71E16 01D71F40

[b]NID 30 [Jack] SPDIF Out at Ext Fron[/b]t
Node - 0x1E
Pin Default - 0x02451120
Verb - 01E71C20 01E71D11 01E71E45 01E71F02

[b]NID 31 [N/A] Speaker at Ext Rear[/b]
Node - 0x1F
Pin Default - 0x411111f0
Verb - 01F71CF0 01F71D11 01F71E11 01F71F41

6920G_Nodes.doc

[THe KiNG]

I did it! Since THe KiNG mention that MuteGPIO value depend on VREF value, so I check back my codec dump. I found that no VREF entry for speaker & headphone. So, I just remove MuteGPIO entry for both devices. After that, both speaker & headphone working (auto-switch). I also compare it with AppleHDA.kext (ALC883) patched with Taruga patcher & it match.

----

That's what I mean when I said "Read Well"

[coconup]

latest version for alc883/notebook: no sound assertions, autoswitch between internal mic and line in. Now every jack connection is shown as 'combo' like in real macbooks and I deleted the mutegpio entries for hp, internal speakers and spdif out. I also changed the verbs with some macbooks values (now the only difference is e1 instead of e0 in the spdif out's color and misc entry 'cos apparently my spdif out has 'no presence' capability).

 

ALC883.zip

 

the king, have you already tried to patch the SignalProcessing values? It would be cool to be able to modify them to adjust volumes and other stuff..

 

ps: what happened to the voodoohda project?

[THe KiNG]

latest version for alc883/notebook: no sound assertions, autoswitch between internal mic and line in. Now every jack connection is shown as 'combo' like in real macbooks and I deleted the mutegpio entries for hp, internal speakers and spdif out. I also changed the verbs with some macbooks values (now the only difference is e1 instead of e0 in the spdif out's color and misc entry 'cos apparently my spdif out has 'no presence' capability).

 

ALC883.zip

 

the king, have you already tried to patch the SignalProcessing values? It would be cool to be able to modify them to adjust volumes and other stuff..

 

ps: what happened to the voodoohda project?

No I didn't tried yet...I will when I will get some free time to play

About voodoohda it died(main developer is gone) and rebirth(new developers started the work on it)

[Hugo_bee]

hy the king

i've tried to walt through 2 road

1st.. with a retail setup

2nd with normal dvd hack but with vanilla kernel

 

both way bring me and other italians into that situation

 

nobb1x created a kext (a legacy as yours but with separate parts (hda.. platform etc)

this is a good start.. because (except for brutal thousand errors in system log) audio out work fine and so do internal mic

 

and so I tried to verify from your platformdriver embedded in the mega plist.. with our.. but is the same.

then.. how can is possible that 2 weeks ago some people delivered a kext that can run external mike.. and not internal.. and if I try to merge both pathmap.. nothing.. now only internal mic?

 

it's amazing! really...

 

but good to have internal mic good.

the kext is here

http://www.insanelymac.com/forum/index.php...st&id=47385

 

so.. tomorrow i'll erase that legacy.. and retry your 2 kext (therefore italians tell me that they are not so good.. but.. now that i've the environment to test.. i'll test)

 

bye.. night

 

ugo

[kidalive]

All my using Pin Complexs shows below. The widgets in applehdController I set 29 and 31. Is that correct.

Please check my ConfigData I`m not sure the Input parts are correct. `couse I ain`t got the Auto Switch between MicIN and LineIn founction.

11471c10 11471d10 11471e21 11471f01 11571c10 11571d01 11571e13 11571f90 [color="blue"]11971c10 11971d01 11971ea0 11971f90 11871c30 11871d90 11871ea1 11871f01[/color] 11e71c20 11e71d11 11e71e45 11e71f01

Node 0x14 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Pincap 0x083e: IN OUT HP Detect Trigger
 Pin Default 0x0121101f: [Jack] HP Out at Ext Rear
Conn = 1/8, Color = Black
Node 0x15 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
 Pincap 0x083e: IN OUT HP Detect Trigger
 Pin Default 0x99130110: [Fixed] Speaker at Int ATAPI
Conn = ATAPI, Color = Unknown
Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Vref caps: HIZ 50 GRD 80 Pin Default 0x01a19830: [Jack] Mic at Ext Rear
Conn = 1/8, Color = Pink Pin-ctls: 0x24: IN VREF_80
Node 0x19 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Vref caps: HIZ 50 GRD 80 Pin Default 0x99a3093f: [Fixed] Mic at Int ATAPI
Conn = ATAPI, Color = Unknown   Pin-ctls: 0x24: IN VREF_80
Node 0x1c [Pin Complex] wcaps 0x400001: Stereo
 Pincap 0x0820: IN
 Pin Default 0x593301f0: [N/A] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Node 0x1d [Pin Complex] wcaps 0x400000: Mono
 Pincap 0x0820: IN
 Pin Default 0x598301f0: [N/A] Line In at Int ATAPI
Conn = ATAPI, Color = Unknown
Node 0x1e [Pin Complex] wcaps 0x400300: Mono Digital
 Pincap 0x0810: OUT
 Pin Default 0x01451120: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = Black
Node 0x1f [Pin Complex] wcaps 0x400200: Mono Digital
 Pincap 0x0820: IN
 Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black

I come across a issue. When I combined the MIC and the LineIn

in the Pathmap section into 1 item the Mic won`t work. Any idea?

Below is my Inputs Device Info.

I cannot get the Mic at Ext Rear and Mic at Int ATAPI display as MicIn and LineIn like in windows.

I only got 2 inputs. But in the dump I can see a CD at Int and LineIn at Int. Which one should I choose to be the MicAttributes?

Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Pincap 0x08173e: IN OUT HP Detect Trigger
Vref caps: HIZ 50 GRD 80
 Pin Default 0x01a19830: [Jack] Mic at Ext Rear

Node 0x19 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Pincap 0x08173e: IN OUT HP Detect Trigger
Vref caps: HIZ 50 GRD 80
 Pin Default 0x99a3093f: [Fixed] Mic at Int ATAPI

B.T.W I don`t know what HIZ 50 GRD 80 stands for.

[DPyro]

Someone help me get the (edited) verbs?

[THe KiNG]

thankz, i was looking for those threads :censored2:

we are finished here, u are the man

 

EDIT: one last thing that i noticed right now, so i post in for info

frontpanel headphones do not work (work/but no sound)

when u plug in the earphones for example, automatically the sound from the speakers goes mute

and u see in preferences that output from "internal speaker" change to "headphones", that's good

but no sound coming out, not even noise or signal

i did a restart to test in windows, and they worked correctly, so something is wrong with applehda

i add this note, so somebody else try it and post back (ADI1988B last kext from king)

 

though the mic connection (frontpanel again) works correctly (tested earphones as a mic and i record the sound in logic)

 

so all the outputs/inputs work, apart from the headphones in the frontpanel

Something weird going on here

I got a front panel connection cable to test/fix headpones and autoswitch

But I dont get Headpones auto switch when inserted or on mic

Dunno wtf is wrong here mic on front works if i set it separate(not on switch)

But if I add headphones separate i got KP

Maybe is the cable fault dunno will test more oe try to got another one...

[DPyro]

I got internal and external mic to work, but still no sound on internal speaker or headphones. What would cause this? I can change the volume on both, and I even get noise on headphones with the volume at full - it even auto switches to headphones when I plug them in, yet I'm still not getting audio. Would it be something to do with MuteGPIO? How would I figure out what values to input?

 

Your input is appreciated.

ALC889.zip

[warlord]

Hi King,

 

Thx for your Compilation of Infos!

 

I am very interested of getting my HDMI-Audio working. HDMI-Video works (9800 GTX+).

My Soundchip is an ALC1200 (P5Q-SE), Could i get Node 17 to Work?

 

borrowed from Signal64 Post:

ATAPI Unknown SPDIF Out at Int ATAPI 17 0x11 0x99430140 01171c40 01171d01 01171e43 01171f99

 

I'd tried to get it to work but it is recognized as Unknown Built-In Output with no Controls and no Audio over it.

From the CodecDump (under Alsa < v18a its recognized as ALC888 - Most Pins are the same, i think Codec too) wich i converted into a graph i saw that Node 16 (Stereo Digital) is Conected to 17. Also i saw that there is no AMP Node connected so i think thats the reason for no Volume control but do you maybe know a way to maybe unmute it so it will gives me sound.

 

It's an Onboard SP/DIF so i think it will work (have to put a cord between the Mobo an the GraphicCard).

[Riley Freeman]

Thanks for ALL the info (there's a lot!). I'm slowly getting my head around it with some help.

 

I'm trying to get a CMI9880 running and have just one quick question: what if your codec doesn't have an audio mixer?

 

You can see the layout in the attached codec graph (I can't attach a svg file so while I was zipping I also threw in the codec dump).

 

With just two nodes nothing shows up in Input or Output Devices.

9880hda.zip

[slipttees]

any solution for my controller ALC888S 3CH ?

 

 

Ubuntu 8.10 Dump.

Intel_code0.txt

[DPyro]

Thanks for ALL the info (there's a lot!). I'm slowly getting my head around it with some help.

 

I'm trying to get a CMI9880 running and have just one quick question: what if your codec doesn't have an audio mixer?

 

You can see the layout in the attached codec graph (I can't attach a svg file so while I was zipping I also threw in the codec dump).

 

With just two nodes nothing shows up in Input or Output Devices.

 

Does your sound actually work in linux? If your codec graph looks like that, I'm assuming no.

[Riley Freeman]

Does your sound actually work in linux? If your codec graph looks like that, I'm assuming no.

It works with the Mandriva 2009 LiveCD that I used for the codec dump. I have a pair of speakers plugged in and get sound on Youtube etc and I can hear the shutdown sound when quitting Mandriva. It also shows up as an audio capture device so I assume input works too.