Leopard on Series 7 NVIDIA nForce MCP + Intel CPU MOBOs

[Uscg.Matthew]

Okay, so here is the update. I uploaded the AppleHDA File for ALC888 on the EVGA 750i SLI FTW mobo. I get Digital out(optical out), Headphones (Front port) , and line out (Green jack in the rear) along with microphone in's from the front and rear. all working great with hda patcher.

 

The digital out, has no slider for volume control, for me this is no issue due to the fact that i use a 5.1 surround sound system.

 

As for as video goes, still no go on a the 7950 gt ko ... Any ideas :S

[verdant]

Okay, so here is the update. I uploaded the AppleHDA File for ALC888 on the EVGA 750i SLI FTW mobo. I get Digital out(optical out), Headphones (Front port) , and line out (Green jack in the rear) along with microphone in's from the front and rear. all working great with hda patcher.

 

The digital out, has no slider for volume control, for me this is no issue due to the fact that i use a 5.1 surround sound system.

 

As for as video goes, still no go on a the 7950 gt ko ... Any ideas :S

 

Hi Matthew,

 

Glad you got your audio sorted......

 

If NVEnabler or any other injector kext did not work together, modifying the following Info.plist files as described below (based on procedure explained by Krazubu on IM) :

 

Add your GFX card device ID to the NVDAResman.kext Info.plist:

Go to /System/Library/Extensions/NVDAResman.kext > Show Contents > Contents > Info.plist....

 

Add your GFX card device ID to the NVDANV40Hal.kext

Go to /System/Library/Extensions/NVDANV40Hal.kext > Show Contents > Contents > Info.plist....

 

Add your GFX card device ID to the Info.plist of NVEnabler, NVdarwin, NVKush, or NVinject etc....(these injecter kexts should all work in a similar manner....) and set the NVCAP string correctly

 

DVI-I / DVI-I - BAAAAAAAAwAMAAAAAAAABwAAAAA=

VGA / DVI-I - BAAAAAAAAQAGAAAAAAAAAAAAAAA=

DVI-I / VGA - BAAAAAAAAwAEAAAAAAAABwAAAAA=

 

and set the IOProbeScore value to 0

 

Go to /System/Library/Extensions/"your chosen injector".kext > Show Contents > Contents > Info.plist....

 

Also, check for the appropriate data value against VRAM,totalsize for your graphics card VRAM

 

Data Value -------- VRAM (MB) ---------- String Value (Hexadecimal)

 

<00000002>-------------32------------------<0x02000000>

<00000004>-------------64------------------<0x04000000>

<00000008>------------128------------------<0x08000000>

<00000010>------------256------------------<0x10000000>

<00000014>------------320------------------<0x14000000>

<00000020>------------512------------------<0x20000000>

<00000028>------------640------------------<0x28000000>

<00000030>------------768------------------<0x30000000>

<00000038>------------896------------------<0x38000000>

<00000040>-----------1024 (1GB)----------<0x40000000>

<00000060>-----------1500 (1.5 GB)-------<0x60000000>

<00000080>-----------2000 (2 GB)---------<0x80000000>

 

using Property List Editor (available in XCode > Developer > Applications > Utilities) .......

 

Repair Extensions

 

sudo chown -R root:wheel /System/Library/Extensions

sudo chmod -R go=u-w /System/Library/Extensions

sudo touch /System/Library/Extensions

 

Reboot

 

then, see here and here and here.......may be the only solution to your GFX card problem.....

[Uscg.Matthew]

Thanks for those instructions sir I am looking a bit more into it now. I am wondering though.. When you say, input my gfx card device id into the info.plist... Where in the text should i insert it? :S i am still researching how to do it... SO if i do find out before you reply, i will edit this

 

Thanks!

[verdant]

Thanks for those instructions sir I am looking a bit more into it now. I am wondering though.. When you say, input my gfx card device id into the info.plist... Where in the text should i insert it? :S i am still researching how to do it... SO if i do find out before you reply, i will edit this

 

Thanks!

 

It should go in the list under <key>IOPCIPrimaryMatch</key> in NVDAResman

 

<string>0x011010de&0xfff8ffff 0x017010de&0xfff8ffff 0x017910de 0x018010de&0xfff8ffff 0x018810de 0x018910de 0x020010de&0xfff8ffff 0x025010de&0xfff8ffff 0x028010de&0xfff8ffff 0x030010de&0xfff8ffff 0x031010de&0xfff8ffff 0x031910de 0x034910de</string>

 

and in the list under <key>IOPCIPrimaryMatch</key> in NVDANV40Hal.kext

 

<string>0x004010de&0xfff0ffff 0x00f010de&0xfff0ffff 0x022010de&0xfff0ffff 0x014010de&0xfff0ffff 0x016010de&0xfff0ffff 0x009010de&0xfff0ffff 0x01d010de&0xfff0ffff 0x039010de&0xfff0ffff 0x029010de&0xfff0ffff</string>

 

and in the list under <key>IOPCIMatch</key> in the injector kext......

 

<string>0x019310de 0x004010de 0x004110de 0x004210de 0x004310de 0x004410de 0x004510de 0x004610de 0x004710de 0x004810de 0x009010de 0x009110de 0x009210de 0x009310de 0x009510de 0x009810de 0x009910de 0x00C010de 0x00C110de 0x00C210de 0x00C310de 0x00C810de 0x00C910de 0x00F010de 0x00F110de 0x00F210de 0x00F310de 0x00F410de 0x00F510de 0x00F610de 0x00F910de 0x00FA10de 0x00FB10de 0x00FC10de 0x014010de 0x014110de 0x014210de 0x014310de 0x014410de 0x014510de 0x014610de 0x014710de 0x014810de 0x014910de 0x014F10de 0x016010de 0x016110de 0x016210de 0x016310de 0x016410de 0x016610de 0x016710de 0x016810de 0x016910de 0x016A10de 0x019110de 0x019310de 0x019410de 0x019710de 0x01D010de 0x01D110de 0x01D310de 0x01D610de 0x01D710de 0x01D810de 0x01DD10de 0x01DF10de 0x021110de 0x021210de 0x021510de 0x021810de 0x022110de 0x022210de 0x024010de 0x024110de 0x024210de 0x024410de 0x024710de 0x029010de 0x029110de 0x029210de 0x029310de 0x029410de 0x029510de 0x029710de 0x029810de 0x02E010de 0x02E110de 0x02E310de 0x02E410de 0x030110de 0x030210de 0x031110de 0x031210de 0x031410de 0x031A10de 0x031B10de 0x032010de 0x032110de 0x032210de 0x032310de 0x032410de 0x032510de 0x032610de 0x032710de 0x032810de 0x032C10de 0x032D10de 0x033010de 0x033110de 0x033210de 0x033310de 0x033410de 0x034110de 0x034210de 0x034310de 0x034410de 0x034710de 0x034810de 0x039010de 0x039110de 0x039210de 0x039310de 0x039410de 0x039510de 0x039810de 0x039910de 0x03D010de 0x03D110de 0x03D210de 0x03D510de 0x040010de 0x040110de 0x040210de 0x040310de 0x040410de 0x040510de 0x040710de 0x040810de 0x040910de 0x042010de 0x042110de 0x042210de 0x042310de 0x042410de 0x042510de 0x042610de 0x042710de 0x042810de 0x042E10de 0x053110de 0x053310de 0x053A10de 0x053B10de 0x053E10de 0x060010de 0x060210de 0x060410de 0x060610de 0x060910de 0x060C10de 0x060D10de 0x061010de 0x061110de 0x061210de 0x062210de 0x064710de 0x064810de 0x064910de 0x064B10de 0x06E410de 0x06E510de 0x06E810de 0x06E910de 0x07E010de 0x07E110de 0x07E310de 0x084410de 0x084810de 0x084910de 0x084A10de 0x084B10de 0x084F10de 0x004E10de 0x009D10de 0x00CC10de 0x00CD10de 0x00CE10de 0x00F810de 0x00FC10de 0x00FD10de 0x00FE10de 0x014A10de 0x014C10de 0x014D10de 0x014E10de 0x016510de 0x019D10de 0x019E10de 0x01D710de 0x01DA10de 0x01DB10de 0x01DC10de 0x01DE10de 0x024510de 0x029A10de 0x029B10de 0x029C10de 0x029D10de 0x029E10de 0x029F10de 0x030810de 0x030910de 0x031C10de 0x032A10de 0x032B10de 0x033810de 0x033F10de 0x034C10de 0x034E10de 0x039E10de 0x040A10de 0x040B10de 0x040C10de 0x040D10de 0x040E10de 0x040F10de 0x042910de 0x042A10de 0x042B10de 0x042D10de 0x042F10de 0x061A10de 0x061C10de 0x011010de 0x011110de 0x011210de 0x011310de 0x017010de 0x017110de 0x017210de 0x017310de 0x017410de 0x017510de 0x017610de 0x017710de 0x017810de 0x017910de 0x017A10de 0x017C10de 0x017D10de 0x018110de 0x018210de 0x018310de 0x018510de 0x018810de 0x018A10de 0x018B10de 0x018C10de 0x01A010de 0x01F010de 0x020010de 0x020110de 0x020210de 0x020310de 0x025010de 0x025110de 0x025310de 0x025810de 0x025910de 0x025B10de 0x028010de 0x028110de 0x028210de 0x028610de 0x028810de 0x028910de 0x028C10de 0x002010de 0x002810de 0x002910de 0x002C10de 0x002D10de 0x00A010de 0x010010de 0x010110de 0x010310de 0x015010de 0x015110de 0x015210de 0x015310de 0x040d10de 0x05E110de 0x05E210de</string>

 

For example above, 0x040210de (10de is the Vendor ID for most nVidia cards and 0402 is the device ID for a 8600GT).....use OSx86Tools to find your graphics card device ID......

[Uscg.Matthew]

Thanks so very much!!! Will keep you updated !

 

Also here are the 2 kexts that give FULL audio for nforce boards with ALC888 ..... Works perfect. I was mistaken in my other post. I forgot to mention the modified AppleHDA works hand and hand with ALCinject to give front audio, and rear audio including optical out.

 

I will keep you updated on the 7950 deal. Thanks!

[Uscg.Matthew]

Sir. Thank you so very much ! I can confirm that the 7950 GT KO is now working! and showing 512 mb's of vram. ALSO, in the process, overclocked it even more with that flashed file!!! I AM SO HAPPY!

[verdant]

Sir. Thank you so very much ! I can confirm that the 7950 GT KO is now working! and showing 512 mb's of vram. ALSO, in the process, overclocked it even more with that flashed file!!! I AM SO HAPPY!

 

Glad to have helped......enjoy OS X.......

[changethursday]

Hey, heres where I get hung up

 

Im using iDeneb 10.5.5 currently.(I also have tried iatkos v7 but during install end up with the kernal panic that pops up over my install)

 

Using cpus=1 i can get into the installer and install fine. Ive tried a few settings, but the only thing thats "worked" has been

 

(selected at install as per this thread http://www.insanelymac.com/forum/index.php...ode=linearplus)

 

9.4.0 kernal

Jmicron

MCP67

ACPI FIX

 

When I do that, I can boot into OS X, but only in safe mode. I get only one functioning monitor, and no interwebs. USB works, Firewire works (but im not sure how well..it at least recognizes one of my devices, a behringer fca202 audio interface)

 

I have the 9600 GSO card and use two monitors, but havent gotten so far as getting natit or titan or kush or anything on there working. Id like the get the OS booting normal and internet functioning first.

 

Im booting onto a bran new WD SATA 1 GB drive partitioned in two. 750 gigs of storage, and the rest is my mac install, both are MAC Journaled format.

 

Ive gotten JaS10.4.8 working perfectly before on my old HP, but i got the screaming new quad core, and I do a lot of video work, and get really tried of windows being a suckfest for that sort of work, and want to play around with FCP and CS 3/4 for Mac.

 

Let me know if anything has any ideas for iatkos v7 or iDeneb 10.5.5! Im sure its probably some stupid BIOS setting or something..i tried following the chart listed, but didnt see all of the options in my BIOS..

 

 

thanks!

[verdant]

Hey, heres where I get hung up

 

Im using iDeneb 10.5.5 currently.(I also have tried iatkos v7 but during install end up with the kernal panic that pops up over my install)

 

Using cpus=1 i can get into the installer and install fine. Ive tried a few settings, but the only thing thats "worked" has been

 

(selected at install as per this thread http://www.insanelymac.com/forum/index.php...ode=linearplus)

 

9.4.0 kernal

Jmicron

MCP67

ACPI FIX

 

When I do that, I can boot into OS X, but only in safe mode. I get only one functioning monitor, and no interwebs. USB works, Firewire works (but im not sure how well..it at least recognizes one of my devices, a behringer fca202 audio interface)

 

I have the 9600 GSO card and use two monitors, but havent gotten so far as getting natit or titan or kush or anything on there working. Id like the get the OS booting normal and internet functioning first.

 

Im booting onto a bran new WD SATA 1 GB drive partitioned in two. 750 gigs of storage, and the rest is my mac install, both are MAC Journaled format.

 

Ive gotten JaS10.4.8 working perfectly before on my old HP, but i got the screaming new quad core, and I do a lot of video work, and get really tried of windows being a suckfest for that sort of work, and want to play around with FCP and CS 3/4 for Mac.

 

Let me know if anything has any ideas for iatkos v7 or iDeneb 10.5.5! Im sure its probably some stupid BIOS setting or something..i tried following the chart listed, but didnt see all of the options in my BIOS..

 

 

thanks!

 

If you can only boot into OS X using cpus=1 it is likely that you have a "bad" DSDT.aml being loaded by your BIOS......you need to generate a "patched" BIOS using fassl's DSDT Patcher and put it in /Extra generated by installing the Chameleon 2.0 V3 bootloader.......see post #1

 

The BIOS template in post #1 is a composite for many MOBOs with the same nForce chipset, so your BIOS may/will not have all of the parameters/options shown.....

 

When initially installing OS X do not select to install any video, network and audio options.......first focus on getting the basic OS X system running OK......these drivers can be installed later using Kext Helper b7.....

 

Recommend you use the Voodoo 9.5.0 kernel with 9.5.0 System.kext and 9.5.0 seatbelt.kext.....

[changethursday]

If you can only boot into OS X using cpus=1 it is likely that you have a "bad" DSDT.aml being loaded by your BIOS......you need to generate a "patched" BIOS using fassl's DSDT Patcher and put it in /Extra generated by installing the Chameleon 2.0 V3 bootloader.......see post #1

 

The BIOS template in post #1 is a composite for many MOBOs with the same nForce chipset, so your BIOS may/will not have all of the parameters/options shown.....

 

When initially installing OS X do not select to install any video, network and audio options.......first focus on getting the basic OS X system running OK......these drivers can be installed later using Kext Helper b7.....

 

Recommend you use the Voodoo 9.5.0 kernel with 9.5.0 System.kext and 9.5.0 seatbelt.kext.....

 

How do I go about installing chameleon, and then adding the patch? Ive seen people who are used to terminal commands talk about it, but no clear "how tos" per se. Is it something I do from the safemode boot of OS X (10.5.5) or something else? I can install Chameleon vis my iatkos disc as it is an install option, but wouldnt know how to add Fassl's bit from there..

[PumaSpeedDrift]

Hey,

 

As a user of nForce mobo's I have some basic expierence. Currently I am running OSX 10.5.7 (yea I know old but hey it works ) on the MCP67/nforce 560 mobo (in laptop), and have had NOT a single problem!! Since I will be getting a new tower and such:

TigerDirect Barebones 750i SLI ready system

 

with an Intel Core 2 Duo processor and NVidia 9500GT SLI ready Graphics Card with 1Gb of Mem.

 

I will be installing OSX of course. And I will report my goods/bads and what I did to get it up and working as per instructions found in this thread, plus my own edits and settings (as it may work for some, but not for others depending on your type of mobo+proc).

 

If anyone has any heads up before I begin, please say so, as this can really help in my trials and tribulations during Install.

 

Well I will report back (more after XMas) when i get my sys up and running. (Yes it will be dual boot with Vista or Win7 haven't decided yet).

 

Thanx for your heads up for any help you may suggest during/before the time I get up and going.

[verdant]

How do I go about installing chameleon, and then adding the patch? Ive seen people who are used to terminal commands talk about it, but no clear "how tos" per se. Is it something I do from the safemode boot of OS X (10.5.5) or something else? I can install Chameleon vis my iatkos disc as it is an install option, but wouldnt know how to add Fassl's bit from there..

 

 

1. Boot up OS X using cpus=1

 

2. Run Dr. Hurt's Chameleon 2.0 RC3 installer from here to install the Chameleon bootloader on your OS X hard drive.....

 

3. Get fassl's DSDT patcher from here (read the readme for instructions) to generate a patched dsdt.aml file that you should rename to DSDT.aml and then put the DSDT.aml file in the /Extra folder generated by the Chameleon 2.0 RC3 on the hard drive OS X volume....

[changethursday]

So, update time:

 

Im running iPC (10.5.6) right now, and its working..mostly.

 

Internet is fine (found the driver)

 

Firewire is fine (my audio is a firewire interface..didnt even need a driver)

 

USB is fine

 

DVD drive works

 

Doesnt recognize my older IDE drive (though my DVD drive is IDE?)

 

Ive got both screens working on my 9600 GSO 768. I dont have QE and CI is software right now. Also, im getting a number of random lines across my screen wherever i open a window/drop down menu.

 

Doesnt recognize my mobo/cpu etc when i look at "hardware" under about this mac. Though it does say "Jeremy Clark's MS-7380" ..so it got the info somewhere!?

 

Only recognizes 1 core of my 4 (q6600) via cpu-x

 

 

Also, i turned off my screensaver (set it to "never" in the control panel), but it keeps coming up after a certain amount of time..

 

 

Other than that everything is shiny so far..ive tried a number of video drivers via UInstaller and OSx86tools, and currently am running the NVDarwin from the iPC disc, but they all give me the same results..

 

I know im close to having this running like a champ..grrr..

[hitoku]

...i have a problem.

I have the nVidia 630i and the Setup wont go over "Validating Pakage Payload"....

 

NEED HELP ^^

 

e:/ Forgot the System Specs:

 

Intel Core2Quad Q9650x4@3.00 Ghz

2/4 GB RAM (I can Switch fast)

750 GB Samsung HDD [1.Partition WinXP | 2.Partition Win7 | 3. Partition Mac OS X]

2 Disk Drives

Nvidia 9600GT Gaphic Card

 

Actually i had installed Mac, but i did Delete it, and now i want it back ^^

[hitoku]

It worked (i dont know why), I am writing from My Hackint0sh ^^

[timothychew]

I oredi try it out

 

BUt I am using iatkos 7

 

it seem like QE still not working

 

I am using 7300gs 256mb

 

Help

[1NzAn3]

Hey Verdant,

 

as you can see my specs can you tell me if i am able to install OSX Snow leopard on it?

 

thanks

 

XFX 680i LT (Nvidia Nforce 680i Lt Chipsets)

Intel Core 2 QUAD 2.83GHZ

4GB RAM NVIDIA SLI MEMORY

1 TB SEAGATE SATA

1 SATA DVD DRIVE

BFG Nvidia GTX285 1GB

Zalman F4T4L1TY Case

26inch Samsung Monitor

[verdant]

Hey Verdant,

 

as you can see my specs can you tell me if i am able to install OSX Snow leopard on it?

 

thanks

 

XFX 680i LT (Nvidia Nforce 680i Lt Chipsets)

Intel Core 2 QUAD 2.83GHZ

4GB RAM NVIDIA SLI MEMORY

1 TB SEAGATE SATA

1 SATA DVD DRIVE

BFG Nvidia GTX285 1GB

Zalman F4T4L1TY Case

26inch Samsung Monitor

 

You should be able to if you can run Leopard on it OK......

 

I oredi try it out

 

BUt I am using iatkos 7

 

it seem like QE still not working

 

I am using 7300gs 256mb

 

Help

 

Which injector kexts have you tried......and have you PCIClassMatch "fixed" your nVidia graphics kexts?......see post #1

[chandl34]

I installed iDeneb 10.5.5 on my system a few days ago, and am trying to get QE/CI support for my eVGA 9800 GTX+.

 

My other specs:

XFX 750i SLI motherboard

Intel Core 2 Quad 2.83 GHz (Q9550)

2x2gb DDR2

IDE DVD-RW

SATA HDD

 

What I've done:

- Installed iDeneb 10.5.5 with only

- - 9.4 XNU kernel

- - AppleNForceATA

- - JMicronATA

- - ACPI Fix

- - Firewire remove

- - X11

- Upgraded with iDeneb 10.5.8 combo upgrade (now using 9.5 Voodoo kernel)

- Manually inserted EFI string from EFIStudio in com.apple.Boot.plist

- Upgraded Chameleon to v2 RC2 (for DSDT support)

- Used DSDT Patcher GUI to generate a dsdt.aml (after this, I could use 2 cores instead of 1)

- Inserted PCIClassMatch into .kext's in the OP

 

 

What else do you think I should try? Thanks for the help.

[verdant]

I installed iDeneb 10.5.5 on my system a few days ago, and am trying to get QE/CI support for my eVGA 9800 GTX+.

 

My other specs:

XFX 750i SLI motherboard

Intel Core 2 Quad 2.83 GHz (Q9550)

2x2gb DDR2

IDE DVD-RW

SATA HDD

 

What I've done:

- Installed iDeneb 10.5.5 with only

- - 9.4 XNU kernel

- - AppleNForceATA

- - JMicronATA

- - ACPI Fix

- - Firewire remove

- - X11

- Upgraded with iDeneb 10.5.8 combo upgrade (now using 9.5 Voodoo kernel)

- Manually inserted EFI string from EFIStudio in com.apple.Boot.plist

- Upgraded Chameleon to v2 RC2 (for DSDT support)

- Used DSDT Patcher GUI to generate a dsdt.aml (after this, I could use 2 cores instead of 1)

- Inserted PCIClassMatch into .kext's in the OP

 

 

What else do you think I should try? Thanks for the help.

 

Have you been here.......?

[chandl34]

Yes, I tried that too with 10.5.5 installed. I've also been trying to setup 10.5.2 with Leo Graphics updates + EFI strings, but haven't got it working yet. Kalyway 10.5.2 with the JMicron fix for IDE-DVD is crashing with ACPI panic errors before reaching the installer.

[changethursday]

Heres where Im at

 

Ive got the OS up and running

 

GRAPHICS:

I have a 9600 GSO 768, and have tried a variety of graphics solutions. I can get both monitors and full resoultion, but no CI/QE going. Right now im on the 5700FX or something driver (ive tried all the 8800 and some 9XXX drivers all with the same result)

 

Im getting lines in various places on the screen, especially drop down menus. Im including a pic.

 

CPU:

Right now im only getting 1 core recognized. Im booting with CPUS=1, because my machine will keep restarting if I dont. Ive tried a few different fixes, but it always hoses my install. When i use the various DSDT patches, i see that when i -v boot ill see it recognize all my cores, but the boot will fail somewhere else down the line.

 

Audio:

No prob, using my firewire interface, works great

 

Firewire/USB:

No problems

 

Internet:

no problems (using the .pkg installer linked from this thread)

 

 

 

I would love any help with the Grpahics/CPU issues! I have the feeling i have to get my board recognized correctly before the graphics will work right, but I could be wrong..

 

 

BTW, im using iPC 10.5.6

[verdant]

Heres where Im at

 

Ive got the OS up and running

 

GRAPHICS:

I have a 9600 GSO 768, and have tried a variety of graphics solutions. I can get both monitors and full resoultion, but no CI/QE going. Right now im on the 5700FX or something driver (ive tried all the 8800 and some 9XXX drivers all with the same result)

 

Im getting lines in various places on the screen, especially drop down menus. Im including a pic.

 

CPU:

Right now im only getting 1 core recognized. Im booting with CPUS=1, because my machine will keep restarting if I dont. Ive tried a few different fixes, but it always hoses my install. When i use the various DSDT patches, i see that when i -v boot ill see it recognize all my cores, but the boot will fail somewhere else down the line.

 

Audio:

No prob, using my firewire interface, works great

 

Firewire/USB:

No problems

 

Internet:

no problems (using the .pkg installer linked from this thread)

 

 

 

I would love any help with the Grpahics/CPU issues! I have the feeling i have to get my board recognized correctly before the graphics will work right, but I could be wrong..

 

 

BTW, im using iPC 10.5.6

 

Follow manual procedure here......your graphics hopefully will work.

 

For patched DSDT.aml file, did you run fassl's DSDT Patcher after booting with cpus=1......?

[changethursday]

When i run Fassl's patcher, i notice it recognizes my 4 cores (at startup in verbose mode) but it always hoses my installation..something else fails buring boot. Ill try it again and post what comes up in -v at the fail point, because i forgot what it is off the top of my head..

 

 

Much thanks for the other link..ive been killing myself on the baords looking, but havent seen that thread!

[changethursday]

heres what happens when I use the DSDT GUI Patcher

 

I selected Force Compile and New HPET

 

I tried it both with HPET enabled and disabled in my BIOS, but this is where it froze up each time during startup.